Philips SCD520 Kullanım kılavuzu

SCD520

2

3

1

4

SCD520

ENGLISH 6

DANSK 20

DEUTSCH 34

 49

ESPAÑOL

65

SUOMI 820

FRANÇAIS 93

ITALIANO

107

NEDERLANDS 121

NORSK 135

PORTUGUÊS 148

SVENSKA 163

TÜRKÇE

177

6

Introduction

Congratulations on your purchase and welcome to Philips AVENT! To fully benet from the support

that Philips AVENT offers, register your product at www.philips.com/welcome.

Philips AVENT is dedicated to producing caring, reliable products that give parents the reassurance

they need. This Philips AVENT baby monitor provides round-the-clock support by ensuring you can

always hear your baby clearly without any distracting noise. The DECT technology guarantees zero

interference from other wireless appliances and a crystal clear signal between the baby unit and the

parent unit. The temperature sensor enables you to monitor the temperature in your baby’s room,

and offers you personalised settings to help keep your baby’s room comfortable.

General description (Fig. 1)

A Parent unit

1 On/off button

3

2 Slot for belt clip

3 TALK button

4 MENU button

5 LINK light

6 Microphone

7 Loudspeaker

8 Menu and volume +/– buttons

9 OK button

10 Display

11 Sound level lights

12 Belt clip

13 Adapter

14 Small appliance plug

15 Charger

16 Charging light

17 Compartment for rechargeable batteries

18 Neck strap

19 Lid of compartment for rechargeable batteries

20 Rechargeable batteries (included)

21 Opening for neck strap

B Baby unit

1 On/off button

3

2 PAGE button

3 Play/stop button

E

4 Lullaby button

K

5 Battery light

T

6 Nightlight button

Q

7 Power-on light

8 Volume +/– buttons

9 Microphone

10 Adapter

11 Large appliance plug

12 Loudspeaker

13 Temperature sensor

14 Socket for large appliance plug

15 Compartment for non-rechargeable batteries

16 Lid of compartment for non-rechargeable batteries

17 Non-rechargeable batteries (not included)

ENGLISH

C Display

1

Ñ° = room temperature indication

2

R= sound alert

3

K = lullaby

4

Q = nightlight

5

T = battery symbol

For other display indications and volume/sensitivity levels, see chapters ‘Features’ and ‘Menu options’.

Important

Read this user manual carefully before you use the appliance and save it for future reference.

Danger

Never immerse any part of the baby monitor in water or any other liquid.

Warning

Check if the voltage indicated on the adapters of the baby unit and the charger corresponds to

the local mains voltage before you connect the appliance.

Only use the adapter supplied to connect the baby unit to the mains.

Only use the charger and adapter supplied to charge the parent unit.

The adapters contain a transformer. Do not cut off the adapters to replace them with other

plugs, as this causes a hazardous situation.

If the adapters are damaged, always have them replaced with one of the original type in order

to avoid a hazard. For the correct type, see chapter ‘Replacement’.

If the charger of the parent unit is damaged, always have it replaced with one of the original

type.

Never use the baby monitor in moist places or close to water.

Except for the battery compartments, do not open the housing of the baby unit and parent unit

in order to prevent electric shock.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given

supervision or instruction concerning use of the appliance by a person responsible for their

safety.

Children should be supervised to ensure that they do not play with the appliance.

Caution

Use and store the appliance at a temperature between 10°C and 40°C.

Do not expose the baby unit and parent unit to extreme cold or heat or to direct sunlight. Do

not put the baby unit and the parent unit close to a heating source.

Make sure the baby unit and the cord are always out of reach of the baby (at least 1 metre/3

feet away).

Never place the baby unit inside the baby’s bed or playpen.

Never cover the parent unit and the baby unit with anything (e.g. a towel or blanket).

Always place non-recheargeable batteries of the correct type in the baby unit.

Always place rechargeable batteries of the correct type in the parent unit.

If you place the parent unit next to a transmitter or other DECT appliance (e.g. a DECT

telephone), the connection with the baby unit may be lost.

General

This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult

supervision and should not be used as such.

The temperature sensor only measures the temperature in the baby room. It cannot be used

to control or adjust the temperature in the baby room.

-

ENGLISH 7



This Philips AVENT appliance complies with all standards regarding electromagnetic elds (EMF). If

handled properly and according to the instructions in this user manual, the appliance is safe to use

based on scientic evidence available today.

Preparing for use

Baby unit

You can use the baby unit from the mains or on non-rechargeable batteries. Even if you are going to

use the unit from the mains, we advise you to insert the non-rechargeable batteries. This guarantees

automatic back-up in case of mains failure.

Mains operation

1 Put the large appliance plug in the baby unit and put the adapter in a wall socket (Fig. 2).

The power-on light goes on.

Operation on non-rechargeable batteries

The baby unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use

Philips LR6 PowerLife batteries.

Do not use rechargeable batteries, as the baby unit does not have a charging function.

Unplug the baby unit and make sure your hands and the unit are dry when you insert the non-

rechargeable batteries.

1 Remove the lid of the compartment for non-rechargeable batteries. (Fig. 3)

2 Insert four non-rechargeable batteries (Fig. 4).

Note: Make sure the + and - poles point in the right direction.

3 Reattach the lid. (Fig. 5)

Note: When the batteries are low, the battery light on the baby unit ashes red.

Parent unit

Operation on rechargeable batteries

The parent unit comes with two rechargeable NiMH AAA 900mAh batteries.

Charge the parent unit before you use it for the rst time or when the parent unit indicates that the

batteries are low (the empty battery symbol ashes on the display and the parent unit beeps). The

parent unit starts indicating that the batteries are low 30 minutes before the batteries are

completely empty.

Note: If the batteries are completely empty, the parent unit automatically switches off and loses contact

with the baby unit.

1 Remove the lid of the compartment for the rechargeable batteries (Fig. 6).

2 Insert the rechargeable batteries (Fig. 7).

Note: Make sure the + and - poles of the batteries point in the right direction.

3 Reattach the lid (Fig. 8).

4 Insert the small appliance plug into the charger, put the adapter in a wall socket and place the

parent unit in the charger (Fig. 9).

The charging light on the charger goes on.

The display shows a charging battery symbol to indicate that the parent unit is charging.

5 Leave the parent unit in the charger until the batteries are fully charged.

During charging, the charging light on the charger lights up continuously.

,

ENGLISH8

When the batteries are fully charged, the display of the parent unit shows a full battery

symbol T.

When you charge the parent unit for the rst time or after a long period of disuse, switch it

off and let it charge continuously for at least 10 hours.

Charging normally takes 8 hours, but it takes longer when the parent unit is switched on while

charging. To keep the charging time as short as possible, switch off the parent unit during

charging.

When the batteries are fully charged, the parent unit can be used cordlessly for at least 24

hours.

Note: When the parent unit is charged for the rst time, the operating time is less than 24 hours. The

batteries only reach their full capacity after you have charged and discharged them four times.

Note: When the parent unit is not in the charger, the batteries gradually discharge, even when the parent

unit is switched off.

Using the appliance

1

Place the parent unit and the baby unit in the same room to test the connection (Fig. 10).

Make sure the baby unit is at least 1 metre/3 feet away from the parent unit.

2 Press and hold the on/off button 3 on the baby unit until the green power-on light goes

on. (Fig. 11)

Note: The power-on light always lights up green, even when there is no connection with the parent unit.

The nightlight lights up briey and then goes out again.

The battery light

T lights up briey and then goes out again. (Fig. 12)

3 Press and hold the on/off button 3 on the parent unit until the sound level lights light up

briey. (Fig. 13)

The display goes on and the battery symbol appears on the display (Fig. 14).

The LINK light ashes red and the message ‘Searching’ appears on the display. (Fig. 15)

The LINK light on the parent unit turns green and lights up continuously when a connection

has been established between the baby unit and parent unit. The message ‘Linked’ appears on

the display. (Fig. 16)

After 2 seconds the message ‘Linked’ disappears and the temperature value is shown on the

display. (Fig. 17)

If no connection is established, the LINK light on the parent unit stops ashing and lights up

red. The parent unit beeps from time to time and the message ‘Not Linked’ appears on the

display. (Fig. 18)

Positioning the baby monitor

1 Place the baby unit at least 1 metre/3 feet away from your baby (Fig. 19).

2 Place the parent unit within the operating range of the baby unit. Make sure it is at least 1

metre/3 feet away from the baby unit to avoid acoustic feedback (Fig. 20).

For more information on the operating range, see section ‘Operating range’ below.

Operating range

The operating range of the baby monitor is 330 metres/1000 feet in open air. Depending on the

surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is

up to 50 metres/150 feet.

Dry materials Material thickness Loss of range

Wood, plaster, cardboard, glass

(without metal, wires or lead)

< 30cm/12in 0-10%

,

-

,

ENGLISH 9

Dry materials Material thickness Loss of range

Brick, plywood < 30cm/12in 5-35%

Reinforced concrete < 30cm/12in 30-100%

Metal grilles or bars < 1cm /0.4in 90-100%

Metal or aluminium sheets < 1cm/0.4in 100%

For wet and moist materials, the range loss may be up to 100%.

Features

The following features are described in chapter ‘Menu options’, as they can only be operated in the

menu of the parent unit:

Adjusting microphone sensitivity

Sound alert on/off

Setting room temperature range (minimum and maximum temperature)

Temperature alert on/off

Adjusting loudspeaker volume

1 Press the volume + or – button on the baby unit until the desired loudspeaker volume for

the baby unit has been reached (Fig. 21).

Note: You can only set the loudspeaker volume on the baby unit when a lullaby is playing.

2 Press the volume + or – button on the parent unit until the desired loudspeaker volume for

the parent unit has been reached (Fig. 22).

The display gives visual feedback on the volume settings of the parent unit:

j = volume switched off/silent baby monitoring

k = minimum volume

l = maximum volume

Note: If the volume is set to a high level, the units consume more power.

Talk function

You can use the TALK button on the parent unit to talk to your baby (e.g. to comfort your baby).

1 Press and hold the TALK button and talk clearly into the microphone from a distance of 15-

30cm (Fig. 23).

The green LINK light starts ashing and the message ‘Talk’ appears on the display.

2 Release the TALK button when you have nished talking.

Sound level lights

The parent unit continuously monitors the sound level in your baby´s room and the sound level

lights let you know if there is any activity. If your baby cries, you see the sound level lights light up on

the parent unit.

As long as the baby unit does not detect a sound, all sound level lights on the parent unit are

out.

When the baby unit picks up a sound, one or more sound level lights on the parent unit go on.

The number of lights that go on is related to the loudness of the sound picked up by the baby

unit.

-

,

-

,

-

ENGLISH10

Nightlight

Note: You can also switch the nightlight on and off in the menu of the parent unit (see chapter ‘Menu

options’, section ‘Nightlight’).

1 Press the nightlight button Q on the baby unit to switch on the nightlight. (Fig. 24)

Q appears on the display of the parent unit.

2 Press the nightlight button Q again to switch off the nightlight.

The nightlight dims gradually before it goes out completely.

Q disappears from the display of the parent unit.

Tip: Switch off the nightlight when you operate the baby unit on the non-rechargeable batteries. This

saves power.

Paging the parent unit

If you have misplaced the parent unit and its volume is switched off, you can use the PAGE button

on the baby unit to locate the parent unit.

Note: The paging function only works when the parent unit is switched on.

1 Press the PAGE button on the baby unit (Fig. 25).

The message ‘Paging’ appears on the display of the parent unit.

The parent unit produces a paging alert tone.

2 To stop the paging alert tone, press the PAGE button again or press any button on the parent

unit.

Lullaby function

Note: You can also operate the lullaby function in the menu of the parent unit (see chapter ‘Menu

options’, section ‘Lullaby function’).

1 Press the play/stop button E on the baby unit to play the currently selected

lullaby. (Fig. 26)

The lullaby starts to play and repeats continuously.

2 To stop the lullaby, press the play/stop button E on the baby unit again. (Fig. 26)

3 To select another lullaby when a lullaby is playing: (Fig. 27)

Press the lullaby button K on the baby unit.

Wait 2 seconds for the next lullaby to start.

If you want another lullaby, press the lullaby button K on the baby unit again.

Out of range alert

When the parent unit is out of range of the baby unit, the parent unit beeps from time to time and

the message ‘Not linked’ appears on the display. The LINK light on the parent unit ashes red.

Note: The message ‘Not Linked’ also appears on the display of the parent unit when the baby unit is

switched off.

Menu options

Most functions can be operated on both the baby unit and the parent unit, but some functions can

only be operated in the menu of the parent unit.

Menu operation - general explanation

Note: Menu functions can only be operated when a connection has been established between the baby

unit and the parent unit.

,

-

ENGLISH 11

1 Press the MENU button to open the menu (Fig. 28).

The rst menu option appears on the display.

2 Use the – and + buttons to select the desired menu option (Fig. 29).

Note: The arrow indicates in which direction you can navigate.

3 Press the OK button to conrm (Fig. 30).

4 Use the + and - buttons to select the desired setting.

5 Press the OK button to conrm.

The new setting ashes twice and then disappears from the display.

6 Press the MENU button again to exit the menu.

Nightlight on/off

1 Select ‘Light’ with the + and - buttons.

2 Press the OK button to conrm.

3 If the nightlight is off, the display shows ‘On?’. Press the OK button to switch on the

nightlight. If the nightlight is on, the display shows ‘Off?’. Press the OK button to switch off

the nightlight.

Lullaby function

Selecting a lullaby

1 Select ‘Lullaby’ with the + and - buttons.

2 Press the OK button to conrm.

3 Press the + button once or several times to select one of the ve lullabies from the list or to

select ‘Play All’.

4 Press the OK button to conrm.

When you have selected one of the ve lullabies, it plays continuously.

Switching to another lullaby

1 Press the + button to choose another lullaby from the list.

2 Press the OK button to conrm.

Pausing a lullaby

1 Press the OK button.

The message ‘Paused’ appears on the display.

2 Press the OK button again to continue the lullaby.

If you do not continue the lullaby within 20 seconds, the lullaby function switches off automatically.

The message ‘Paused’ and the lullaby symbol disappear from the display.

Stopping a lullaby

1 Press the + button to select ‘Stop’ from the list.

2 Press the OK button to conrm.

Adjusting microphone sensitivity

Note: You can only adjust the microphone sensitivity in the menu of the parent unit.

,

ENGLISH12

You can set the microphone sensitivity of the baby unit to the desired level. You can only change the

microphone sensitivity when a connection between the baby unit and the parent unit has been

established, i.e. when the LINK light on the parent unit lights up green continuously.

1 Select ‘Sensitivity’ with the + and - buttons.

2 Press the OK button to conrm.

3 Select the desired microphone sensitivity level for the baby unit with the + and - buttons.

k = minimum sensitivity level

l = maximum sensitivity level

4 Press the OK button to conrm.

The message ‘Saved’ appears on the display.

Note: When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and

therefore transmits more often. As a result, the units consume more power.

Sound alert on/off

Note: You can only switch the sound alert on and off in the menu of the parent unit.

This feature allows you to monitor your baby silently. It enables you to switch off the volume on

your parent unit and still be alerted if your baby cries.

If the sound alert is switched on, the parent unit beeps as soon as the fourth sound level light lights

up blue while the volume is switched off. In addition, the backlight of the parent unit display goes on

and the sound alert symbol (R) ashes on the display.

1 Select ‘Sound Alert’ with the + and - buttons.

2 Press the OK button to conrm.

3 If the alert is off, the display shows ‘On?’. Press the OK button to switch on the alert. If the

alert is on, the display shows ‘Off?’. Press the OK button to switch off the alert.

If you have set the sound alert to ‘on’, the sound alert symbol ( R) appears on the display of

the parent unit.

Setting room temperature range

Note: You can only adjust the temperature range in the menu of the parent unit.

A baby will sleep comfortably in a room heated to a temperature between 16°C and 20°C. This is

important, since a baby cannot regulate its body temperature as well as an adult. A baby needs

more time to adjust to temperature changes.

If you do not set a temperature range, the baby monitor alerts you when the temperature in your

baby’s room drops below 14°C or rises above 30°C. In this case, the backlight of the parent unit

display goes on and ‘High’ or ‘Low’ appears on the display. To change the default minimum and

maximum temperature, follow the instructions below.

Note: The temperature of the baby’s room is shown on the display of the parent unit when they are

linked.

1 Select ‘Temperature’ with the + and - buttons.

2 Press the OK button to conrm.

3 Select ‘Range’ with the + and - buttons.

4 Press the OK button to conrm.

5 Set the desired minimum temperature with the + and - buttons.

6 Press the OK button to conrm.

7 Set the desired maximum temperature with the + and - buttons.

,

ENGLISH 13

8 Press the OK button to conrm.

The message ‘Saved’ appears on the display.

Note: If the temperature in the baby’s room drops below or exceeds the set temperature range, the

display of the parent unit is on continuously. This causes the unit to consume more power.

Temperature alert on/off

Note: You can only switch the temperature alert on and off in the menu of the parent unit.

Note: If the temperature alert is activated too often, reduce the set minimum temperature and/or

increase the set maximum temperature (see ‘Setting room temperature range’).

If the temperature alert is switched on, the parent unit beeps if the actual room temperature

exceeds the set maximum temperature or drops below the set minimum temperature. In addition,

the backlight of the parent unit display goes on and ‘High’ or ‘Low’ appears on the display. If no

minimum and maximum temperatures have been set, the temperature alert is given when the room

temperature drops below 14°C or rises above 30°C.

1 Select ‘Temperature’ with the + and - buttons.

2 Press the OK button to conrm.

3 Select ‘Alert’ with the + and - buttons.

4 Press the OK button to conrm.

5 If the alert is off, the display shows ‘On?’. Press the OK button to switch on the alert. If the

alert is on, the display shows ‘Off?’. Press the OK button to switch off the alert.

Reset function

This function in the menu of the parent unit allows you to reset both the parent unit and the baby

unit to the default settings at the same time. You can use this function if problems occur that you

cannot solve by following the suggestions in chapter ‘Frequently asked questions’.

1 Select ‘Reset’ with the + and - buttons.

2 Press the OK button to conrm.

The message ‘Conrm?’ appears on the display of the parent unit.

3 Press the OK button to conrm.

The parent unit switches off and then switches on again.

The units have now both been reset to the default factory settings.

Default settings

Parent unit

Loudspeaker volume: 1

Microphone sensitivity: 3

Sound alert: off

Temperature alert: off

‘Temperature low’ alert: 14°C

‘Temperature high’ alert: 30°C

Baby unit

Loudspeaker volume: 3

Nightlight: off

Lullaby: 1

,

-

ENGLISH14

Accessories

Belt clip and neck strap

If the batteries of the parent unit are sufciently charged, you can take the unit with you inside and

outside the house if you attach the unit to your belt or waistband with the belt clip or if you hang it

around your neck with the neck strap. This allows you to monitor your baby while you are moving

around.

Connecting the belt clip

1 Snap the belt clip onto the parent unit (Fig. 31).

Disconnecting the belt clip

1 Pull the belt clip off the parent unit.

Connecting the neck strap

1 Insert the end loop of the neck strap through the hole behind the strap post. Thread the

neck strap through the end loop and pull the neck strap tight (Fig. 32).

Disconnecting the neck strap

1 Pass the neck strap though the end loop and pull the end loop out of the hole behind the

strap post.

Cleaning and maintenance

Do not immerse the parent unit and the baby unit in water and do not clean them under the tap.

Do not use cleaning spray or liquid cleaners.

1 Unplug the baby unit if it is connected to the mains and take the parent unit out of the

charger.

2 Clean the parent unit and the baby unit with a damp cloth.

Make sure the parent unit is dry before you put it back into the plugged-in charger.

3 Clean the charger with a dry cloth.

4 Clean the adapters with a dry cloth.

Storage

When you are not going to use the baby monitor for some time, remove the non-rechargeable

batteries from the baby unit and the rechargeable batteries from the parent unit. Store the

parent unit, the baby unit, the charger of the parent unit and the adapters in a cool and dry

place.

Replacement

Baby unit

Batteries

Only replace the non-rechargeable batteries of the baby unit with four non-rechargeable 1.5V R6

AA batteries.

Note: We strongly advise you to use Philips non-rechargeable batteries.

Adapter

Only replace the adapter of the baby unit with an adapter of the original type.You can order a new

adapter from your dealer or a Philips service centre.

-

ENGLISH 15

UK only: BD075040D

Other countries: VD075040D

Parent unit

Batteries

Only replace the rechargeable batteries of the parent unit with two rechargeable NiMh AAA

900mAh batteries.

Note: We strongly advise you to use Philips rechargeable batteries.

Adapter

Only replace the adapter of the parent unit charger with an adapter of the original type.You can

order a new adapter from your dealer or a Philips service centre.

UK only: BD075040D

Other countries: VD075040D

Environment

Do not throw away the appliance with the normal household waste at the end of its life, but

hand it in at an ofcial collection point for recycling. By doing this, you help to preserve the

environment (Fig. 33).

Rechargeable and non-rechargeable batteries contain substances that may pollute the

environment. Do not throw away rechargeable and non-rechargeable batteries with the normal

household waste, but hand them in at an ofcial collection point. Always remove rechargeable

and non-rechargeable batteries before you discard and hand in the appliance at an ofcial

collection point.

Guarantee and service

If you need service or information or if you have a problem, please visit the Philips AVENT website

at www.philips.com/AVENT or contact the Philips Consumer Care Centre in your country (you

nd its phone number in the worldwide guarantee leaet). If there is no Consumer Care Centre in

your country, go to your local Philips dealer.

Frequently asked questions

This chapter lists the questions most frequently asked about the appliance. If you cannot nd the

answer to your question, contact the Customer Care Centre in your country.

Question Answer

Why don’t the power-on

light of the baby unit and

the LINK light of the

parent unit come on

when I press the on/off

buttons of the units?

Perhaps the batteries of the parent unit are empty and the parent

unit is not in the plugged-in charger. Insert the small appliance plug

into the charger, put the adapter of the charger in a wall socket and

place the parent unit in the charger. Then press the on/off button to

establish connection with the baby unit.

Perhaps the non-rechargeable batteries of the baby unit are empty

and the baby unit is not connected to the mains. Replace the non-

rechargeable batteries or connect the baby unit to the mains. Then

press the on/off button to establish connection with the parent unit.

The baby unit and the parent unit may be out of range of each other.

Move the parent unit closer to the baby unit, but not closer than 1

metre/3 feet.

-

ENGLISH16

Question Answer

If the LINK light on the parent unit still does not start to ash, use the

reset function to reset the units to their default settings.

Why does the LINK light

on the parent unit light

up red continuously and

why is the message

‘Not Linked’ shown on

the display?

The baby unit and the parent unit are out of range of each other.

Move the parent unit closer to the baby unit.

The baby unit may be switched off. Switch on the baby unit.

Why does the battery

light on the baby unit

ash red?

The non-rechargeable batteries of the baby unit are running low.

Replace the non-rechargeable batteries or connect the baby unit to

the mains (see chapter ‘Preparing for use’).

Why does the parent unit

beep?

If the parent unit beeps while the LINK light lights up red continuously

and the message ‘Not Linked’ is shown on the display, the connection

with the baby unit is lost. Move the parent unit closer to the baby

unit.

If the parent unit beeps and the battery symbol on the display is

empty, the rechargeable batteries of the parent unit are running low.

Recharge the batteries.

If you have switched off the volume while the sound alert is on, the

parent unit beeps whenever the fourth sound level light lights up

because the baby unit has picked up a sound.

If you have set the room temperature range on the parent unit and

the temperature alert is on, the parent unit beeps when the

temperature drops below the set level or below 14°C or when the

temperature rises above the set level or above 30°C.

The baby unit may be switched off. Switch on the baby unit.

Why does the appliance

produce a high-pitched

noise?

The units may be too close to each other. Make sure the parent unit

and the baby unit are at least 1 metre/3 feet away from each other.

The volume of the parent unit may be set too high. Decrease the

volume of the parent unit.

Why don’t I hear a

sound/Why can’t I hear

my baby cry?

The volume of the parent unit may be set too low or may be

switched off. Increase the volume of the parent unit.

The microphone sensitivity level of the baby unit may be set too low.

Set the microphone sensitivity level to a higher level in the menu of

the parent unit.

The baby unit and the parent unit may be out of range of each other.

Reduce the distance between the units.

Why does the parent unit

react too quickly to other

sounds?

The baby unit also picks up other sounds than those of your

baby. Move the baby unit closer to the baby (but observe the

minimum distance of 1 metre/3 feet).

ENGLISH 17

Question Answer

The microphone sensitivity level of the baby unit may be set too high.

Decrease the microphone sensitivity level in the menu of the parent

unit.

Why does the parent unit

react slowly to the baby’s

crying?

The microphone sensitivity level of the baby unit may be set too low.

Increase the microphone sensitivity level of in the menu of the parent

unit.

Why do the non-

rechargeable batteries of

the baby unit run low

quickly?

The microphone sensitivity level of the baby unit may be set too high,

which causes the baby unit to transmit more often. Decrease the

microphone sensitivity level in the menu of the parent unit.

The volume on the baby unit may be set too high, which causes the

baby unit to consume a lot of energy. Decrease the volume of the

baby unit.

You may have set a maximum room temperature that is lower than

the actual room temperature or a minimum room temperature that

is higher than the actual room temperature. The baby unit continues

to send data to the parent unit and therefore uses more power.This

causes the non-rechargeable batteries of the baby unit to run low

quickly.

Perhaps you have switched on the nightlight. If you want to use the

nightlight, we advise you to run the baby unit on mains power.

Why does the charging

time of the parent unit

exceed 8 hours?

The parent unit may be switched on during charging. Switch off the

parent unit during charging.

The specied operating

range of the baby

monitor is 330

metres/1000 feet. Why

does my baby monitor

manage a much smaller

distance than that?

The specied range is only valid outdoors in open air. Inside your

house, the operating range is limited by the number and type of walls

and/or ceilings in between. Inside the house, the operating range is up

to 50 metres/150 feet.

Why is the

connection lost every

now and then? Why are

there sound

interruptions?

The baby unit and the parent unit are probably close to the outer

limits of the operating range. Try a different location or decrease the

distance between the units. Please note that it takes about 30

seconds each time before a connection between the units is

established.

What happens during a

power failure?

If the parent unit is sufciently charged, it continues to operate during

a power failure, both inside and outside the charger. If there are

batteries in the baby unit, it also continues to operate during a power

failure.

Is my baby monitor

secure from

eavesdropping and

interference?

The DECT technology of this baby monitor guarantees no

interference from other equipment and no eavesdropping.

ENGLISH18

Question Answer

The operating time of the

parent unit is supposed

to be at least 24 hours.

Why is the operating

time of my parent unit

shorter?

When the parent unit has been charged for the rst time, the

operating time is less than 24 hours. The rechargeable batteries only

reach their full capacity after you have charged and discharged

them at least four times.

The volume of the parent unit may be set too high, which causes the

parent unit to consume a lot of energy. Decrease the volume of the

parent unit

The microphone sensitivity level of the baby unit may be set too high,

which causes the parent unit to consume a lot of energy. Decrease

the microphone sensitivity level in the menu of the parent unit.

Why doesn’t battery

symbol appear on the

display of the parent unit

when I start to recharge

the parent unit?

It may take a few minutes before the battery symbol appears on the

display of the parent unit when you charge the parent for the rst

time or after a long period of disuse.

ENGLISH 19

20

Introduktion

Tillykke med dit køb og velkommen til Philips AVENT! For at få fuldt udbytte af den support, Philips

AVENT tilbyder, skal du registrere dit produkt på www.philips.com/welcome.

Philips AVENT udvikler og producerer pålidelige produkter, der kan give forældre den tryghed, de

har brug for. Denne Philips AVENT-babyalarm hjælper dig døgnet rundt ved at sikre, at du altid kan

høre din baby klart og tydeligt uden forstyrrende støj. DECT-teknologien garanterer, at der ikke

forekommer interferens fra andre trådløse apparater, og den giver et klart signal mellem babyenhed

og forældreenhed. Temperatursensoren gør det muligt for dig at holde øje med temperaturen i

børneværelset, og sensorens personlige indstillinger hjælper dig med at holde børneværelset

behageligt.



A Forældreenhed

1 On/Off-knap

3

2 Åbning til bælteclips

3 TALK-tast

4 MENU-tast

5 LINK-lysindikator

6 Mikrofon

7 Højttaler

8 Menu- og lydstyrketaster +/–

9 OK-tast

10 Display

11 Lys, som indikerer lydniveau

12 Bælteclips

13 Adapter

14 Lille apparatstik

15 Oplader

16 Opladeindikator med lys

17 Rum til genopladelige batterier

18 Halsstrop

19 Låg på rum til genopladelige batterier

20 Genopladelige batterier (medfølger)

21 Åbning til halsstrop

B Babyenhed

1 On/Off-knap

3

2 PAGE-tast

3 Play/stop-tast

E

4 Vuggevise-tast

K

5 Batteriindikator

T

6 Natlystast

Q

7 Lysindikator for tændt

8 Lydstyrke +/– taster

9 Mikrofon

10 Adapter

11 Stort apparatstik

12 Højttaler

13 Temperatursensor

14 Tilslutning til stort apparatstik

15 Rum til ikke-genopladelige batterier

16 Låg på rum til ikke-genopladelige batterier

17 Ikke-genopladelige batterier (medfølger ikke)

DANSK

Sayfa yükleniyor ...

Philips SCD520 Kullanım kılavuzu

Bu kılavuz için de uygundur

Philips SCD520 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler