Lenovo ThinkPad 43R2018 Kullanım kılavuzu

Th inkPad USB Portable Se cure

Hard Drive User Guide

Note

Before installing the product, be sure to read the information in Lenovo Limited

Warranty on page B-1 and Before you begin the installation on page 3.

First Edition (November 2008)

LENOVO products, data, computer software, and services have been developed

exclusively at private expense and are sold to governmental entities as commercial items

as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and

disclosure.

LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or

services are delivered pursuant a General Services Administration ″GSA″ contract, use,

reproduction, or disclosure is subject to restrictions set forth in Contract No.

GS-35F-05925.

Contents

About the ThinkPad USB Portable Secure Hard Drive . . . . . . . 1

Product description . . . . . . . . . . . . . . . . . . . 1

Secure Hard Drive button panel . . . . . . . . . . . . . . . 2

Installing the Secure Hard Drive . . . . . . . . . . . . . . 3

Before you begin the installation . . . . . . . . . . . . . . . 3

Installing the Secure Hard Drive . . . . . . . . . . . . . . . 3

Using the Secure Hard Drive . . . . . . . . . . . . . . . . 5

Entering and exiting the Standby Mode, Admin Mode, and User Mode 5

Entering the Standby Mode . . . . . . . . . . . . . . . . 5

Entering the Admin Mode . . . . . . . . . . . . . . . . 5

Exiting the Admin Mode . . . . . . . . . . . . . . . . . 6

Entering the User Mode . . . . . . . . . . . . . . . . . 6

Exiting the User Mode . . . . . . . . . . . . . . . . . 6

Password

Management . . . . . . . . . . . . . . . . . . 6

Changing the Admin Password . . . . . . . . . . . . . . 6

Adding a new User Password . . . . . . . . . . . . . . . 7

Deleting the User Passwords . . . . . . . . . . . . . . . 8

Changing

the User Password . . . . . . . . . . . . . . . 8

Completely resetting the Secure Hard Drive . . . . . . . . . . . 9

Initializing and formatting the Secure Hard Drive after a complete reset 9

Using the ThinkVantage Rescue and Recovery program with the Secure

Hard Drive . . . . . . . . . . . . . . . . . . . . . 10

Hibernating,

Suspending, or Logging off from the operating system . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . . . . 12

Appendix A. Service and Support . . . . . . . . . . . . . . A-1

Registering your option . . . . . . . . . . . . . . . . . . A-1

Online technical support . . . . . . . . . . . . . . . . . A-1

Telephone technical support . . . . . . . . . . . . . . . . A-1

Appendix B. Lenovo Limited Warranty . . . . . . . . . . . . B-1

Warranty Information . . . . . . . . . . . . . . . . . . B-5

Suplemento de Garantía para México . . . . . . . . . . . . . B-7

Appendix C. Notices . . . . . . . . . . . . . . . . . . C-1

Recycling information . . . . . . . . . . . . . . . . . . C-2

Trademarks . . . . . . . . . . . . . . . . . . . . . . C-3

Appendix D. Electronic emission notices . . . . . . . . . . . D-1

Federal Communications Commission (FCC) Declaration of Conformity D-1

Appendix E. Important information for the European Directive

2002/96/EC . . . . . . . . . . . . . . . . . . . . . E-1

Appendix F. China RoHS . . . . . . . . . . . . . . . . . F-1

iv ThinkPad USB Portable Secure Hard Drive User Guide

About the ThinkPad USB Portable Secure Hard Drive

This manual provides information about the ThinkPad

®

USB Portable Secure

Hard Drive.

The appendices of this guide contain warranty information and legal notices.

Note: Before you install and use the option, be sure to read Before you begin

the installation on page 3.

This option package includes:

v ThinkPad USB Portable Secure Hard Drive with a primary USB data cable

v Auxiliary power cable

v USB data extension cable

v Carrying case

v ThinkPad USB Portable Secure Hard Drive Setup Poster

Product description

The ThinkPad USB Portable Secure Hard Drive (hereafter called the Secure

Hard Drive) is a portable, light-weight, high-speed USB 2.0 standard option

that offers high level data security. In addition to all the regular USB hard disk

drive functions, it also provides you with an easy-to-use full disk encryption

solution. All the functions are integrated into the Secure Hard Drive, therefore,

you can manage passwords and access the Secure Hard Drive without using

other software applications.

The Secure Hard Drive has three working modes:

v Standby Mode (In this mode, the Secure Hard Drive is locked.)

v User Mode (In this mode, the Secure Hard Drive is unlocked.)

v Admin Mode (In this mode, the Secure Hard Drive is locked.)

Note:

Passwords are required for the Admin Mode and User Mode.

Accordingly, they are called Admin Password and User Password.

Secure Hard Drive button panel

The Secure Hard Drive button panel is shown as follows:

OK

1

button

2

button

3 Indicator light

The

button can be used to:

v Cancel current operation

v Return to the previous step when you knowingly entered a wrong password

v Exit the Admin Mode

The

button can be used to access the Secure Hard Drive and it can also be

used as an OK acknowledgement in the following operations:

v Entering a password

v Confirming a new password

The

indicator light displays the following colors to indicate the various modes

of operation:

v Red: Standby Mode

v Blue: Admin Mode

v Green: User Mode

The

indicator light has other display methods to indicate different status of the

Secure Hard Drive. Details are provided later in this chapter.

2 ThinkPad USB Portable Secure Hard Drive User Guide

Installing the Secure Hard Drive

This chapter provides information about installing the Secure Hard Drive.

Before you begin the installation

Be sure to review the following information before you begin to install and use

the Secure Hard Drive.

Attention: Use only the cables that come with this option. You might damage

the drive if you use a cable not included with the option package. The option

is designed for portable use without an AC power adapter. Do not attach an

AC power adapter to this drive.

v To avoid damaging your Secure Hard Drive, handle with care. When

transporting the drive or when it is not in use, place it in the carrying case

that comes with the option.

v For reliable performance of the Secure Hard Drive, make sure that both USB

cables are attached directly from the drive to the computer USB connectors

or to an AC-powered USB hub. Do not connect the USB cables to a

non-powered USB hub.

Installing the Secure Hard Drive

To install the Secure Hard Drive, do the following:

1. Attach one end of the auxiliary power cable to the Secure Hard Drive, and

then attach the other end to an available USB port on your computer, as

shown:

OK

]

Using the Secure Hard Drive 3

2. Depending on the distance between the Secure Hard Drive and your

computer, attach either the primary USB data cable or the USB data

extension cable to an available USB port. The indicator light turns red, as

shown:

OK

4 ThinkPad USB Portable Secure Hard Drive User Guide

Using the Secure Hard Drive

This chapter provides information about using the Secure Hard Drive.

Entering and exiting the Standby Mode, Admin Mode, and

User Mode

This section provides information about how to enter and exit the Standby

Mode, Admin Mode, and User Mode of your Secure Hard Drive.

Entering the Standby Mode

The Standby Mode is the default working mode of the Secure Hard Drive and

is the gateway to other working modes.

To enter the Standby Mode, attach the Secure Hard Drive to your computer.

The drive automatically goes into Standby Mode and the indicator light turns

red. In this mode, the Secure Hard Drive is locked. It cannot be recognized by

the operating system and it does not provide either the regular functions or the

encryption function. However, it enables you to enter and switch between the

Admin Mode and the User Mode.

Note: To switch between the Admin Mode and the User Mode, you are

required to switch to the Standby Mode first, and then you can enter the

mode of your choice.

Entering the Admin Mode

Note: The Secure Hard Drive cannot be recognized by the operating system in

the Admin Mode.

To enter the Admin Mode, do the following:

1. Attach the USB cable to an available USB port on your computer. The

Secure Hard Drive goes into the Standby Mode, and the indicator light

turns red.

2. Press and hold

+ 0 for five seconds until the indicator light flashes red.

This indicates that you can enter the Admin Password.

3. Enter the Admin Password and press

. The default Admin Password is

123456. The Secure Hard Drive is in Admin Mode when the indicator light

has changed to blue.

Using the Secure Hard Drive 5

Note: If the indicator light flashes red for a few seconds, indicating the Secure

Hard Drive has returned to the Standby Mode, go back to Step 2. This is

due to one of the following conditions:

v You entered an incorrect Admin Password in Step 3.

v No activity was detected within two minutes in the Admin Mode.

Exiting the Admin Mode

To exit the Admin Mode, press the

button in the Admin Mode until the

indicator light turns red. This indicates that you are in the Standby Mode.

Entering the User Mode

To enter the User Mode, do the following:

1. Attach the Secure Hard Drive to your computer. It enters the Standby

Mode.

2. Enter the User Password or the Admin Password and press

. The

indicator light turns green indicating that the drive is in the User Mode. If

the indicator light flashes red, you need to re-enter the correct password.

Exiting the User Mode

To exit the User Mode, double-click the Safely Remove Hardware icon from

the Microsoft

®

Windows

®

desktop, and then remove the Secure Hard Drive

from your computer. Attach the Secure Hard Drive to your computer again

and the indicator light turns red. This indicates that you are in the Standby

Mode.

Password Management

This section provides information about managing your password in the

Admin Mode and User Mode.

Changing the Admin Password

You can change the Admin Password by doing the following:

1. Enter Admin Mode.

2. Press and hold

+ 9 until the indicator light flashes blue.

3. Enter the new password (a minimum of 6 digits and a maximum of 16

digits) and press

. The indicator light flashes green three times.

Note:

If the indicator light flashes red three times, this indicates that the

password is less than 6 digits or more than 16 digits. Enter a

password that contains 6 – 16 digits after the indicator light flashes

blue intermittently.

6 ThinkPad USB Portable Secure Hard Drive User Guide

4. Re-enter the new Admin Password and press

. The indicator light stays

solid green for three seconds and the Admin Password is changed

successfully.

Notes:

a. If the indicator light flashes red intermittently and then blue

intermittently, go back to step 3. This is due to one of the following

conditions:

v You waited longer than 10 seconds before entering a password.

v The new password was entered incorrectly.

b.

If no activity is detected within two minutes in the Admin Mode, the

Secure Hard Drive will return to the Standby Mode.

Adding a new User Password

You can add a new User Password by doing the following:

1. Enter the Admin Mode.

2. Press and hold

+ 1 until the indicator light flashes blue intermittently.

3. Enter a User Password (a minimum of 6 digits and a maximum of 16

digits) and press

. The indicator light flashes green three times.

Note:

If the indicator light flashes red three times, this indicates that the

password is less than 6 digits or more than 16 digits. Enter a

password that contains 6 – 16 digits after the indicator light flashes

blue intermittently.

4. Re-enter the new User Password and press

. If the indicator light stays

solid green for three seconds, the User Password was added successfully.

Note:

If the indicator light flashes red intermittently and then blue

intermittently, go back to step 3. This is due to one of the following

conditions:

v You waited longer than 10 seconds before entering a password.

v The new password was entered incorrectly.

Notes:

1. The Secure Hard Drive enables you to have up to 10 User Passwords in

Admin Mode. When the indicator light flashes red three times and then

returns to solid blue, this indicates that the limit has been reached, and no

additional User Passwords can be added.

2. If no activity is detected within two minutes in the Admin Mode, it will

return to the Standby Mode.

Using the Secure Hard Drive 7

Deleting the User Passwords

You can delete all User Passwords by doing the following:

1. Enter the Admin Mode.

2. Press and hold 7 + 8 +

for five seconds until the indicator light flashes

blue intermittently. After the indicator light flashes green three times and

then blue intermittently.

3. Press and hold 7 + 8 +

a second time for five seconds until the indicator

light goes on solid green for three seconds and then back to solid blue, this

indicates that the User Passwords were deleted successfully.

Changing the User Password

You can change the User Password by doing the following:

1. Enter the User Mode.

2. Press and hold

+ 1 for five seconds until the indicator light flashes red.

3. Enter the current User Password and press

. The indicator light turns

green for three seconds, and then it will flash blue intermittently.

Note:

If the indicator light flashes red intermittently, go back to Step 2.

This is due to one of the following conditions:

v You waited longer than 10 seconds before entering a password.

v The new password was entered incorrectly.

4.

Enter the new password (a minimum of 6 digits and a maximum of 16

digits) and press

. The indicator light flashes green three times and then

blue intermittently.

Note:

If the indicator light flashes red three times, this indicates that the

password is less than 6 digits or more than 16 digits. Enter a

password that contains 6 – 16 digits after the indicator light flashes

blue intermittently.

5. Re-enter the new password and press

. When the indicator light stays

solid green, this indicates that the User Password was changed successfully.

Note:

If the indicator light flashes red three times and then blue

intermittently, go back to Step 4. This is due to one of the following

conditions:

v You waited longer than 10 seconds before entering a password.

v The new password was entered incorrectly.

8 ThinkPad USB Portable Secure Hard Drive User Guide

Completely resetting the Secure Hard Drive

If you forget all the User Passwords or Admin Passwords, you can perform a

complete reset to remove all the User Passwords, and restore the Admin

Password to the default 123456.

Attention: Completely resetting the Secure Hard Drive will erase all the data

on the drive. You will need to partition and format the Secure Hard Drive with

disk management applications.

To perform a complete reset of the drive, do the following:

1. Press and hold the

button while you attach the Secure Hard Drive to

an available USB port on your computer. The indicator light will flash blue

and red alternately.

Note:

If no activity is detected for 30 seconds in this step, the Secure Hard

Drive will go into the Standby Mode.

2. Press and hold

+

+ 2 for 10 seconds until the indicator light turns

solid green for three seconds. You have successfully reset the Secure Hard

Drive.

Initializing and formatting the Secure Hard Drive after a

complete reset

A complete reset of the Secure Hard Drive will erase all information and

partition settings. You will need to initialize and format the Secure Hard Drive.

To initialize your Secure Hard Drive, do the following:

1. After a complete reset, attach the Secure Hard Drive to the computer.

2. Enter the default User Password 123456 and press

to enter the User

Mode.

3. Wait until the operating system successfully installs all the USB device

drivers for the Secure Hard Drive.

4. Right-click My computer, and then click Manage from the Windows

desktop.

5. In the Computer Manage window, click Disk Management. In the Disk

Management window, the Secure Hard Drive is recognized as an

unknown device that is uninitialized and unallocated.

6. Do one of the following to make the drive recognized as a basic drive.

v If the Initialize and Convert Disk Wizard window opens, click Next →

Next → Finish.

v If the Initialize and Convert Disk Wizard window does not open:

a. Right-click Unknown Disk, and then select Initialize Disk.

b. In the Initialize Disk window, click OK.

Using the Secure Hard Drive 9 9

7. Right-click in the blank area under the Unallocated section, and then

select New Partition. The Welcome to the New Partition Wizard window

opens.

8. Click Next.

9. Select Primary partition and click Next.

10. If you need only one partition, accept the default partition size and click

Next.

11. Click Next.

12. Create a volume label, select Perform a quick format, and then click Next.

13. Click Finish.

14. Wait until the format process is complete. The Secure Hard Drive will be

recognized and it is available for use.

Using the ThinkVantage Rescue and Recovery program with

the Secure Hard Drive

If the ThinkVantage

®

Rescue and Recovery

®

program is available on your

computer, you can use the Secure Hard Drive as a storage device. To use the

ThinkVantage Rescue and Recovery program with the Secure Hard Drive, do

the following:

1. Attach the Secure Hard Drive to an available USB port on your computer.

2. Enter your User Password or Admin Password and press

to enter the

User mode.

3. Wait until the operating system recognizes the Secure Hard Drive.

4. Create backups and store them on the Secure Hard Drive using Rescue

and Recovery program.

5. Turn off your computer.

6. Restart your computer with the Secure Hard Drive attached to the

computer.

7. Press F12 to pause the start process, as the Secure Hard Drive needs

several seconds to unlock itself after entering the User Mode.

8. When the Secure Hard Drive is powered on and available, the indicator

light turns solid red. Enter your User password and press

to enter the

User Mode.

9. If the Secure Hard Drive is not displayed in the boot list, restart the

computer by pressing Ctrl + Alt + Del while the Secure Hard Drive

remains attached to the computer.

10. Press F12 and select the Secure Hard Drive from the boot list. Your

computer will start from the Rescue and Recovery workspace on the

Secure Hard Drive.

10 ThinkPad USB Portable Secure Hard Drive User Guide

Note: For more information about the Rescue and Recovery program, go to

http://www.lenovo.com

Hibernating, Suspending, or Logging off from the operating

system

Be sure to save and close all the files on your Secure Hard Drive before

hibernating, suspending, or logging off from the Windows operating system. It

is recommended that you log off the Secure Hard Drive manually before

hibernating, suspending, or logging off from your system. To log off the Secure

Hard Drive, double-click Safely Remove Hardware on the Windows desktop

and remove the Secure Hard Drive from your computer.

Attention: To ensure the data integrity of your Secure Hard Drive, be sure to

lock or log off your Secure Hard Drive if you are:

v away from your computer

v using the switching user function by sharing a computer with others

Using the Secure Hard Drive 11

Troubleshooting

This section contains troubleshooting information for the Secure Hard Drive. If

you encounter any of the following problems when using the Secure Hard

Drive, refer to the corresponding answers.

Q: How do I use the Secure Hard Drive the first time?

A: You can use it in one of the following ways:

v Enter the Admin Mode with 123456 (default administrator password), and

then you are able to change the Admin Password or create a User Password

v Directly enter the Secure User Mode with 123456 (default Admin Password)

to use the Secure Hard Drive

Q:

What can I do if I forget the User Password?

A: Use your Admin Password to enter Admin Mode, and then create another

User Password in Admin Mode.

Q: What can I do if I forget the Admin Password?

A: There is no other way to retrieve the Admin Password except a complete

reset of the Secure Hard Drive. After a complete reset, all data will be lost and

you will need to initialize, allocate and format the Secure Hard Drive

manually. Then you will be able to use the default Admin Password 123456.

Q: Why did the operating system not recognize the Secure Hard Drive after I

enter the User Mode and completely reset the computer?

A: You need to initialize, allocate and format the Secure Hard Drive manually.

For more information, refer to Initializing and formatting the Hard Drive after

a complete reset.

Q: Can I initialize and format the Secure Hard Drive with Windows user

account?

A: No, this is a Windows limitation, you must use the Admin account to

initialize and format the Secure Hard Drive.

Q: How do I use the Secure Hard Drive without a password?

A: As a full disk encryption product, the Secure Hard Drive can never be used

without a password.

12 ThinkPad USB Portable Secure Hard Drive User Guide

Q: What encryption algorithm is used in this product?

A: AES 128 bits algorithm.

Q: Why could I not change my User Password which has the same digits as

the Admin password?

A: You can change it only in the Admin Mode. In the User Mode, the User

Password which has the same digits is created in the Admin Mode cannot be

changed or deleted

Q: Why could I not create recovery media using the ThinkVantage Rescue and

Recovery software?

A: Ensure that your Secure Hard Drive could be accessed correctly. If you still

cannot create recovery media, format the Secure Hard Drive with NTFS file

system of your computer and try again.

Q: Why could I not initialize, partition or format the Secure Hard Drive?

A: Ensure that you have administrator privileges. You can use only the

administrator account to initialize, partition or format the Secure Hard Drive in

the Admin Mode.

Q: Why could the system not boot from the Secure Hard Drive after I entered

the User Password?

A: The Secure Hard Drive is a full disk encryption device that requires several

seconds to unlock after you enter the correct User Password.

1. Press F1 or F12 to pause the boot process to enable the Secure Hard Drive

several seconds to unlock itself.

2. Enter the correct User Password and the indicator light turns green.

3. Press Ctrl + Alt + Del and the Secure Hard Drive will remain in the User

Mode during the reset process and you can then boot from the drive.

Q:

Why could the system not boot from the Secure Hard Drive when it is

attached in a dock?

A: As the dock will shut down the power of USB port during warm boot, the

Secure Hard Drive could not unlock itself in limited time. An easy solution is

to attach the Secure Hard Drive directly to computer (not the dock), and this

will enable the computer to boot from the Secure Hard Drive during a

recovery process.

Troubleshooting 13

ThinkPad USB Portable Secure Hard Drive -

Présentation

Le présent document fournit des informations sur l’unité de disque dur

ThinkPad USB Portable Secure Hard Drive.

Les annexes contiennent les informations relatives à la garantie ainsi que des

mentions légales.

Remarque : Avant d’installer et d’utiliser l’option, veuillez prendre

connaissance des informations figurant à la section Avant de

commencer l’installation, à la page 16.

L’option comprend les éléments suivants :

v Unité de disque dur ThinkPad USB Portable Secure Hard Drive avec un

câble de transmission de données USB principal

v Cordon d’alimentation auxiliaire

v Rallonge pour câble de transmission de données USB

v Mallette de transport

v Livret d’installation ThinkPad USB Portable Secure Hard Drive Setup Poster

Description du produit

L’unité ThinkPad USB Portable Secure Hard Drive (ci-après appelée unité de

disque dur sécurisée) est une unité portable, légère et répondant aux standards

USB 2.0 qui offre un niveau de sécurité des données très élevé. En plus de

toutes les fonctions habituelles d’une unité de disque dur USB, elle fournit une

solution de chiffrement complet du disque facile à utiliser. Toutes les fonctions

sont intégrées à l’unité ; vous pouvez donc gérer les mots de passe et accéder à

l’unité de disque dur sécurisée sans avoir besoin d’autres logiciels.

Trois modes de fonctionnement sont possibles pour l’unité de disque dur

sécurisée :

v Mode Veille (l’unité est alors verrouillée)

v Mode Utilisateur (l’unité est déverrouillée)

v Mode Administrateur (l’unité est verrouillée)

Remarque : Des mots de passe sont requis pour les modes Administrateur et

Utilisateur. Ils sont appelés mot de passe administrateur et mot de

passe utilisateur.

14 ThinkPad USB Portable Secure Hard Drive User Guide

Boutons et voyant de l’unité de disque dur sécurisée

L’unité comporte les boutons et voyant suivants :

OK

1 Bouton

2 Bouton

3 Voyant

Le bouton

peut être utilisé pour :

v Annuler l’opération en cours

v Revenir à l’étape précédente lorsque vous avez entré un mot de passe erroné

v Quitter le mode Administrateur

Le bouton

peut être utilisé pour accéder à l’unité de disque sécurisée et

pour valider les opérations suivantes (il joue alors le rôle d’un bouton OK) :

v Saisie d’un mot de passe

v Confirmation d’un nouveau mot de passe

La couleur du voyant change pour indiquer les différents modes de

fonctionnement :

v Rouge : mode Veille

v Bleu : mode Administrateur

v Vert : mode Utilisateur

Le voyant peut également signaler différents états de l’unité de disque dur

sécurisée. Plus de détails sont fournis dans d’autres chapitres du présent

document.

ThinkPadUSBPortableSecureHardDrive-Présentation 15

Installation de l’unité de disque dur sécurisée

Le présent chapitre fournit des informations sur l’installation de l’unité de

disque dur sécurisée.

Avant de démarrer l’installation

Veuillez lire attentivement les informations suivantes avant d’installer et

d’utiliser l’unité de disque dur sécurisée.

Avertissement : Utilisez uniquement les câbles fournis avec cette option. Vous

risquez d’endommager l’unité si vous utilisez un câble qui n’est pas inclus

dans le coffret de l’option. L’unité de disque dur sécurisée est conçue pour être

utilisée sans boîtier d’alimentation. Ne branchez pas de boîtier d’alimentation

sur l’option.

v Pour éviter d’endommager votre unité de disque dur sécurisée, manipulez-la

avec précaution. Lorsque vous transportez l’unité ou lorsque vous ne

l’utilisez pas, placez-la dans la mallette de transport qui est fournie.

v Pour obtenir des performances fiables, assurez-vous de brancher les deux

câbles USB de l’unité directement sur les ports USB de l’ordinateur ou sur

un concentrateur USB alimenté. Ne connectez pas les câbles USB à un

concentrateur USB qui n’est pas équipé d’un dispositif d’alimentation.

Installation de l’unité de disque dur sécurisée

Pour installer l’unité, procédez comme suit :

1. Branchez une des extrémités du cordon d’alimentation auxiliaire à l’unité

de disque dur sécurisée, puis l’autre à un port USB disponible de

l’ordinateur, comme illustré ci-après.

OK

16 ThinkPad USB Portable Secure Hard Drive User Guide

Sayfa yükleniyor...

Lenovo ThinkPad 43R2018 Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Lenovo ThinkPad 43R2018 Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler