Simplicity 2691359-00 Kullanım kılavuzu

Not for

Reproduction

80079532

A

Not for

Reproduction

2

1

2

3

4

5

6

7

8

Not for

Reproduction

3

9

10

11

12

13

14

15

16

17

18

19

Not for

Reproduction

4

20

21

22

23

24

25

26

Not for

Reproduction

5

Products Covered by This

Manual

The following products are covered by this manual:

2691351-00, 2691351-01, 2691351-02, 2691352-00,

2691352-01, 2691352-02, 2691353-00, 2691353-01,

2691353-02, 2691353-03, 2691357-00, 2691357-01,

2691357-02, 2691359-00, 2691359-01, 2691359-02,

2691359-03, 2691391-00, 2691391-01, 2691391-02,

2691395-00, 2691395-01, 2691395-02, 2691410-00,

2691410-01, 2691410-02, 2691411-00, 2691411-01,

2691411-02, 2691412-00, 2691459-01, 2691460-01

Manual Contents:

Operator Safety..................................................................... 5

Safety Interlock Systems Checks..................................... 10

Features and Controls........................................................11

Operation............................................................................. 12

Maintenance.........................................................................16

Troubleshooting..................................................................19

Specifications......................................................................20

Save these instructions.This manual contains safety

information to make you aware of the hazards and risks

associated with the product and how to avoid them. It also

contains important instructions that should be followed

during the initial set-up, operation, and maintenance of

the product.Save these original instructions for future

reference.

Note:For instructions to install, remove, and level the mower

deck (including belt replacement), see the Mower Deck

Manual supplied with this machine.

Note:The engine information contained in this manual applies

to Briggs & Stratton

®

engines only. For information regarding

non-Briggs engines, refer to the engine manual supplied with

your unit.

The images in this document are representative, and are

meant to complement the instructional copy they accompany.

Your unit may vary from the images displayed. LEFT and

RIGHT are as seen from the operator's position.

Operator Safety

Safety Icons

Callout Description

A Alert.

B Read the manual.

C Fire hazard.

D Thrown objects.

E Amputation - hand in blade.

F Amputation - foot in blade.

G Keep children away.

H Maximum slope angle for safe operation.

I Slippery slopes.

J Amputation - rotating parts.

K Avoid turning down slopes; if possible turn up slopes.

Safety Alert Symbol and Signal Words

The safety alert symbol ( ) is used to identify safety

information about hazards that can result in personal injury. A

signal word (DANGER, WARNING, or CAUTION) is used with

the alert symbol to indicate the likelihood and the potential

severity of injury. In addition, a hazard symbol may be used to

represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates a situation that could result in damage

to the product.

Not for

Reproduction

6

Carbon Monoxide Warning

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

Safety Decals

Before operating your machine, read and understand the

safety decals. Compare Figure1with the table following.

The cautions and warnings are for your safety. To avoid a

personal injury or damage to the machine, understand and

follow all the safety decals.

Important:If any safety decals become worn or damaged,

and cannot be read, order replacement decals from your local

dealer.

A Decal, Main Safety

Part No. 5106566



B Decal, Danger, Thrown

Objects

Part No. 7106109



Safety Decal Icon Definitions

A WARNING:Read and understand the Operator's Manual before

using this machine. Know the location and function of all controls.

Do not operate this machine unless you are trained.

B DANGER - AMPUTATION AND DISMEMBERMENT HAZARD:To

avoid injury from rotating blades and moving parts, keep safety

devices (guards, shields and switches) in place and working.

C DANGER - THROWN OBJECTS AND AMPUTATION

HAZARD:To avoid injury, keep bystanders and children away.

Remove objects that can be thrown by the blades. Do not mow

without discharge chute or entire grass catcher in place.

D DANGER - LOSS OF CONTROL AND ROLL OVER

HAZARD:Operating on slopes can be hazardous and cause a

loss of control and roll-overs. Do not operate on slopes over 10*

degrees. Avoid sudden turns or rapid speed changes. Reduce

speed and use extreme caution on slopes. Avoid turning down

slopes; if possible, turn up slopes. Do not operate down slopes

towards or near water, retaining walls, or drop-offs. Give yourself a

minimum of two mower widths of clearance around these hazards.

E DANGER - AMPUTATION HAZARD:Never carry riders, especially

children, even with the blades off. Do not mow in reverse unless

absolutely necessary. Look down and behind - before and while

backing.

F DANGER: LOSS OF TRACTION, SLIDING, STEERING, AND

CONTROL ON SLOPES HAZARD:If machine stops forward

motion on a slope, stop the blades. and drive slowly off the slope.

G DANGER:Engage parking brake, remove key, and consult

technical literature before performing service or maintenance.

H DANGER - FIRE HAZARD:Remove key and wait three (3) minutes

before refueling.

I DANGER - THROWN OBJECTS HAZARD:Do not mow without

discharge chute or entire grass catcher in place.

Not for

Reproduction

7

J DANGER - THROWN OBJECTS AND AMPUTATION

HAZARD:To avoid injury from rotating blades, stay clear of deck

edge and keep others away.

*This limit was determined per International Standard ISO 5395-3:2013,

Section 4.6 and is based on the ISO 5395-3 Stability Test procedure

described in Annex A. The 10 degree “limit of stability” is equal to 60%

of the angle at which machine lift-off occurred in static tests. Actual

dynamic stability may vary depending on operating conditions.

Slope Identification Guide

How to measure the slope of a lawn surface with a

smartphone or an angle finder tool:

WARNING

Do not operate on slopes greater than degrees.

1. Use a straight edge at least two (2) feet long (A, Figure

2). A 2x4 or a straight piece of metal works well.

2. Angle finder tools.

a. Use your smartphone: Many smartphones (B,

Figure 2) have an inclinometer (angle finder) located

under the compass application (app). Or, search an

app store for an Inclinometer app.

b. Use angle finder tools: Angle finder tools (C & D,

Figure 2) are available at local hardware stores or

online (also called inclinometer, protractor, angle

meter, or angle gauge). Dial type (C) or digital type

(D) work, others may not. Follow user instructions

with the angle finder tool.

3. Place the two (2) feet long straight edge along the

steepest part of the lawn slope. Place the board up and

down the slope.

4. Lay the smartphone or angle finder tool on the straight

edge and read the angle in degrees. This is the slope of

your lawn.

Note:A paper gauge slope identification guide is included

in your product literature packet and is also available to

download from the manufacturer's website.

Safety Rules and Information

WARNING

Read these safety rules and follow them closely. Failure

to obey these rules could result in loss of control of unit,

severe personal injury or death to you, or bystanders, or

damage to property or equipment. This mowing deck is

capable of amputating hands and feet and throwing

objects. The triangle in text signifies important cautions or

warnings which must be followed.

General Operation

1. Read, understand, and follow all instructions in the

manual and on the unit before starting.

2. Do not put hands or feet near rotating parts or under

the machine. Keep clear of the discharge opening at all

times.

3. Only allow responsible adults, who are familiar with the

instructions, to operate the unit (local regulations can

restrict operator age).

4. Clear the area of objects such as rocks, toys, wire, etc.,

which could be picked up and thrown by the blade(s).

5. Be sure the area is clear of other people before mowing.

Stop the unit if anyone enters the area.

6. Never carry passengers.

7. Do not mow in reverse unless absolutely necessary.

Always look down, behind, and to the side before

changing directions.

8. Never direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction.

Material may ricochet back toward the operator. Stop the

blade(s) when crossing gravel surfaces.

9. Do not operate the machine without the entire grass

catcher, discharge guard (deflector), or other safety

devices in place.

10. Slow down before turning.

11. Never leave a running unit unattended. Always disengage

the PTO, set parking brake, stop engine, and remove

keys before dismounting.

12. Disengage blades (PTO) when not mowing. Shut off

engine and wait for all parts to come to a complete stop

before cleaning the machine, removing the grass catcher,

or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial

light.

14. Do not operate the unit while under the influence of

alcohol or drugs.

15. Watch for traffic when operating near or crossing

roadways.

16. Use extra care when loading or unloading the unit into a

trailer or truck.

17. Always wear eye protection when operating this unit.

18. Data indicates that operators, age 60 years and above,

are involved in a large percentage of power equipment-

related injuries. These operators should evaluate their

ability to operate the equipment safely enough to protect

themselves and others from injury.

19. Follow the manufacturer’s recommendations for wheel

weights or counterweights.

20. Keep in mind the operator is responsible for accidents

occurring to other people or property.

21. All drivers should seek and obtain professional and

practical instruction.

22. Always wear substantial footwear and trousers. Never

operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades and

blade hardware are present, intact, and secure. Replace

worn or damaged parts.

Not for

Reproduction

8

24. Disengage attachments before: refueling, removing an

attachment, making adjustments (unless the adjustment

can be made from the operator’s position).

25. When the machine is parked, stored, or left unattended,

lower the cutting means unless a positive mechanical lock

is used.

26. Before leaving the operator’s position for any reason,

disengage the PTO, engage the parking brake (if

equipped), stop the engine, and remove the key.

27. To reduce fire hazard, keep the unit free of grass, leaves,

& excess oil. Do not stop or park over dry leaves, grass,

or combustible materials.

28. It is a violation of California Public Resource Code

Section 4442 to use or operate the engine on or near

any forest-covered, brush-covered, or grass-covered

land unless the exhaust system is equipped with a spark

arrester meeting any applicable local or state laws. Other

states or federal areas may have similar laws.

Transporting And Storage

1. When transporting the unit on an open trailer, make sure

it is facing forward, in the direction of travel. If the unit is

facing backwards, wind lift could damage the unit.

2. Always observe safe refueling and fuel handling practices

when refueling the unit after transportation or storage.

3. Never store the unit (with fuel) in an enclosed poorly

ventilated structure. Fuel vapors can travel to an ignition

source (such as a furnace, water heater, etc.) and cause

an explosion. Fuel vapor is also toxic to humans and

animals.

4. Always follow the engine manual instructions for storage

preparations before storing the unit for both short and

long term periods.

5. Always follow the engine manual instructions for proper

start-up procedures when returning the unit to service.

6. Never store the unit or fuel container inside where there

is an open flame or pilot light, such as in a water heater.

Allow unit to cool before storing.

WARNING

Unsafe Operation Hazard

Do not load this zero-turn rider on a trailer or truck using

two separate ramps. Only use a single ramp that is at least

one foot wider than the width of the rear wheels of this rider.

This rider has a zero turning radius and the rear wheels

could fall off the ramps, or the rider could tip over injuring

the operator or bystanders.

Slope Operation

Slopes are a major factor related to loss-of-control and tip

over accidents, which can result in severe injury or death.

Operation on all slopes requires extra caution. If you feel

uneasy on a slope, do not operate on it.

Control of a zero-turn riding mower sliding on a slope will

not be regained by the application of the brake. The main

reasons for loss of control are: insufficient tire grip on the

ground, speed too fast, inadequate braking, the type of

machine is unsuitable for its task, lack of awareness of the

ground conditions, incorrect hitching and load distribution.

1. Avoid turning down slopes; if possible turn up slopes.

2. Watch for holes, ruts, or bumps. Uneven terrain could

overturn the unit. Tall grass can hide obstacles.

3. Choose a slow speed so that you will not have to stop or

change speeds while on the slope.

4. Do not mow on wet grass. Tires may lose traction.

5. Do NOT operate down slope towards or near water,

retaining walls, or drop-offs.

6. Avoid starting, stopping, or turning on a slope. If machine

stops forward motion on a slope, stop the blades and

drive slowly off the slope.

7. Keep all movement on slopes slow and gradual. Do not

make sudden changes in speed or direction, which could

cause the machine to rollover.

8. Use extra care while operating machines with grass

catchers or other attachments; they can affect the stability

of the unit. Do not use on steep slopes.

9. Do not try to stabilize the machine by putting your foot on

the ground (ride-on units).

10. Do not mow near drop-offs, ditches, or embankments.

The mower could suddenly turn over if a wheel is over

Not for

Reproduction

9

the edge of a cliff or ditch, or if an edge caves in. Give

yourself a minimum of two mower widths of clearance

around these hazards.

11. Do not use grass catchers on steep slopes.

12. Do not mow slopes you cannot back up.

13. Remove obstacles such as rocks, tree limbs, etc.

14. Use slow speed. Tires may lose traction on slopes even

through the brakes are functioning properly.

15. Do not turn on slopes unless necessary, and then, turn

slowly and gradually up slopes, if possible.

WARNING

Unsafe Operation Hazard

Never operate on slopes greater than 10 degrees, a rise of

3-1/2 feet (106 cm) vertically in a 20 feet (607 cm) length.

Select slow ground speed before driving onto slope. In

addition to front weights, use extra caution when operating

on slopes with rear-mounted grass catchers.

Avoid turning down slopes; if possible turn up slopes. Use

caution when changing directions and DO NOT START OR

STOP ON A SLOPE.

Towed Equipment (Ride-On Units)

1. Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the

hitch point.

2. Follow the manufacturer’s recommendations for weight

limit for towed equipment and towing on slopes.

3. Never allow children or others in or on towed equipment.

4. On slopes, the weight of the towed equipment may cause

loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the mowing activity. Never assume that children will

remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind and

down for small children.

4. Never carry children, even with the blade(s) off. They may

fall off and be seriously injured or interfere with safe unit

operation. Children who have been given rides in the past

may suddenly appear in the mowing area for another ride

and be run over or backed over by the machine.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

Emissions

1. Engine exhaust from this product contains chemicals

known, in certain quantities, to cause cancer, birth

defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period and Air

Index information on the engine emissions label.

Service and Maintenance

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other sources

of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where there is

an open flame, spark, or pilot light such as near a water

heater or other appliance.

6. Never fill containers inside a vehicle or on a truck bed

with a plastic bed liner. Always place containers on the

ground away from your vehicle before filling.

7. Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing immediately.

10. Never over-fill the fuel tank. Replace gas cap and tighten

securely.

11. Use extra care in handling gasoline and other fuels. They

are flammable and vapors are explosive.

12. If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

13. Replace all fuel tank caps and fuel container caps

securely.

Service & Maintenance

1. Never run the unit in an enclosed area where carbon

monoxide fumes may collect.

2. Keep nuts and bolts, especially blade attachment bolts,

tight and keep equipment in good condition.

3. Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if they

are not functioning properly.

4. Keep unit free of grass, leaves, or other debris buildup.

Clean up oil or fuel spillage. and remove any fuel-soaked

debris. Allow machine to cool before storage.

5. If you strike an object, stop and inspect the machine.

Repair, if necessary, before restarting.

Not for

Reproduction

10

6. Never make adjustments or repairs with the engine

running.

7. Check grass catcher components and the discharge

guard frequently and replace with manufacturer’s

recommended parts, when necessary.

8. Mower blades are sharp. Wrap the blade or wear gloves,

and use extra caution when servicing them.

9. Check brake operation frequently. Adjust and service as

required.

10. Maintain or replace safety and instructions labels, as

necessary.

11. Do not remove the fuel filter when the engine is hot

as spilled gasoline may ignite. Do not spread fuel line

clamps further than necessary. Ensure clamps grip hoses

firmly over the filter after installation.

12. Do not use gasoline containing METHANOL, gasohol

containing more than 10% ETHANOL, gasoline additives,

or white gas because engine/fuel system damage could

result.

13. If the fuel tank must be drained, it should be drained

outdoors.

14. Replace faulty silencers/mufflers.

15. Use only factory authorized replacement parts when

making repairs.

16. Always comply with factory specifications on all settings

and adjustments.

17. Only authorized service locations should be utilized for

major service and repair requirements.

18. Never attempt to make major repairs on this unit unless

you have been properly trained. Improper service

procedures can result in hazardous operation, equipment

damage and voiding of manufacturer’s warranty.

19. On multiple blade mowers, take care as rotating one

blade can cause other blades to rotate.

20. Do not change engine governor settings or over-speed

the engine. Operating the engine at excessive speed can

increase the hazard of personal injury.

21. Disengage drive attachments, stop the engine, remove

the key, and disconnect the spark plug wire(s) before:

clearing attachment blockages and chutes, performing

service work, striking an object, or if the unit vibrates

abnormally. After striking an object, inspect the machine

for damage and make repairs before restarting and

operating the equipment.

22. Never place hands near the moving parts, such as a

hydro pump cooling fan, when the tractor is running.

(Hydro pump cooling fans are typically located on top of

the transaxle).

23. Units with hydraulic pumps, hoses, or motors: WARNING:

Hydraulic fluid escaping under pressure may have

sufficient force to penetrate skin and cause serious injury.

If foreign fluid is injected into the skin it must be surgically

removed within a few hours by a doctor familiar with this

form of injury or gangrene may result. Keep body and

hands away from pin holes or nozzles that eject hydraulic

fluid under high pressure. Use paper or cardboard, and

not hands, to search for leaks. Make sure all hydraulic

fluid connections are tight and all hydraulic hoses and

lines are in good condition before applying pressure

to the system. If leaks occur, have the unit serviced

immediately by your authorized dealer.

24. WARNING: Stored energy device. Improper release of

springs can result in serious personal injury. Springs

should be removed by an authorized technician.

25. Models equipped with an engine radiator: WARNING:

Stored energy device. To prevent serious bodily injury

from hot coolant or steam blow-out, never attempt to

remove the radiator cap while the engine is running.

Stop the engine and wait until it is cool. Even then, use

extreme care when removing the cap.

Safety Interlock Systems

Checks

WARNING

DO NOT operate machine if any safety interlock or safety

device is not in place and functioning properly. Contact

your dealer immediately for assistance. DO NOT attempt to

defeat, modify or remove any safety device.

Models with Automatic Parking Brake

TEST 1 - Engine must not crank if:

• PTO switch is engaged, OR,

• Ground speed levers are not locked in their START /

PARK positions.

TEST 2 - Engine should crank if:

• PTO switch is NOT engaged, AND,

• Ground speed levers are locked in their START / PARK

positions.

TEST 3 - Engine must shut off if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with ground speed levers not

locked in their START / PARK positions.

TEST 4 - Check mower blade stopping time

The mower blades and mower drive belt should come to

a complete stop within five seconds after the electric PTO

switch is turned off. If mower drive belt does not stop within

five seconds, see your dealer.

Once the engine has stopped, the PTO switch must be turned

off, and the ground speed levers must be locked in their

START/PARK positions in order to start the engine.

Models with Manual Parking Brake

TEST 1 - Engine must not crank if:

• PTO switch is engaged, OR,

• Ground speed levers are not locked in their START /

PARK positions, OR,

• Parking brake is not engaged.

TEST 2 - Engine should crank if:

Not for

Reproduction

11

• PTO switch is NOT engaged, AND,

• Ground speed levers are locked in their START / PARK

positions, AND,

• Parking brake is engaged.

TEST 3 - Engine must shut off if:

• Operator rises off seat with PTO engaged, OR

• Operator rises off seat with ground speed levers not

locked in their START / PARK positions, OR,

• Operator rises off seat with parking brake not engaged.

TEST 4 - Check mower blade stopping time

The mower blades and mower drive belt should come to

a complete stop within five seconds after the electric PTO

switch is turned off. If mower drive belt does not stop within

five seconds, see your dealer.

Once the engine has stopped, the PTO switch must be turned

off, the parking brake must be engaged, and the ground

speed levers must be locked in their START/PARK positions

in order to start the engine.

Features and Controls

Compare the features and controls in Figure3with the table

following.

Ref. Description / Function Icon(s) Definition /

Operation



A Deck Lift Pedal, Cutting Height

Adjustment Pin and Deck Lift Lock

Lever - adjusts cutting height



SeeCutting Height

Adjustment



Forward ground

speed increase - push

lever forward

Neutral - release

lever

Engine start - move

lever out

Reverse ground

speed increase - pull

lever back

B Right Ground Speed Lever -

controls speed and direction of right

drive wheel; also engages parking

brake



Parking brake engage

- move lever out

C Ignition Switch - starts engine  Engine off



Engine on (run)



Engine start



Choke on (closed) -

Briggs engines only



Engine speed fast

D Engine Speed Control - controls

engine speed



Engine speed slow

E PTO Switch - engages and

disengages mower blade clutch



PTO engage - pull up

on switch

F Hour Meter 



Indicates total hours

of engine operation

G Transmission Release Levers -

release transmissions so unit can

roll freely



SeePushing the

Unit by Hand

H Fuel Tank Cap 



Turn cap

counterclockwise to

remove

I Operator's Seat Adjust 



SeeSeat

Adjustments

J Left Ground Speed Lever - controls

speed and direction of left drive

wheel

 Forward ground

speed increase - push

lever forward

Neutral - release

lever

Engine start - move

lever out

Reverse ground

speed increase - pull

lever back

Not for

Reproduction

12

Operation

Oil Recommendations

Oil Capacity: See the Specifications section.

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard

starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause

increased oil consumption. Check oil level more frequently.

C Synthetic 5W-30

D 5W-30

Check Oil Level

See Figure: 4

Before adding or checking the oil

• Make sure the engine is level.

• Clean the oil fill area of any debris.

1. Remove the dipstick (A, Figure 4) and wipe with a clean

cloth.

2. Install and tighten the dipstick (A, Figure 4).

3. Remove the dipstick and check the oil level. Correct oil

level is at the top of the full indicator (B, Figure 4) on the

dipstick.

4. If oil level is low, slowly add oil into the engine oil fill

(C, Figure 4). Do not overfill. After adding oil, wait one

minute and then recheck the oil level.

Note:Do not add oil at the quick oil drain , if equipped. For

location, see Features and Controls.

5. Reinstall and tighten the dipstick (A, Figure 4).

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped)

will either stop the engine or activate a warning device on the

equipment. If this occurs, stop the engine and check the oil

level with the dipstick.

If the oil level is below the ADD mark, add oil until it touches

the FULL mark. Start the engine and check for the correct oil

pressure before you continue to operate the machine.

If the oil level is between the ADD and FULL marks,DO NOT

start the engine. Contact an authorized service dealer to

correct the oil pressure problem.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane / 87 AKI (91 RON). For high

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will cause

damage to engine components, which will not be covered

under warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See Storage. All fuel is not the

same. If starting or performance problems occur, change

fuel providers or change brands. This engine is certified to

operate on gasoline. The emissions control system for this

engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable.

For carbureted engines, high altitude adjustment is

required to maintain performance. Operation without this

adjustment will cause decreased performance, increased

fuel consumption, and increased emissions. Contact

a Briggs & Stratton Authorized Service Dealer for high

altitude adjustment information. Operation of the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude

adjustment is necessary.

Not for

Reproduction

13

Adding Fuel

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 3 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, cigarettes, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting

engine.

1. Clean the fuel cap area of dirt and debris. Remove the

fuel cap (A, Figure5).

2. Fill the fuel tank with fuel. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck (B).

3. Reinstall the fuel cap.

Starting the Engine

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air

cleaner (if equipped) are in place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN / RUN

position, move throttle (if equipped) to FAST position

and crank until engine starts.

WARNING

Running engine gives off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea, fainting or

death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes, or other

openings.

WARNING

• If you do not understand how a specific control

functions, or have not yet thoroughly read the Features

& Controls section, do so now.

• Do NOT attempt to operate the tractor without first

becoming familiar with the location and function of all

controls.

1. While sitting in the operator's seat:

• Models with automatic parking brake: Make

sure the PTO switch is disengaged and the ground

speed control levers are locked in the START/PARK

position. (The parking brake is automatically engaged

when the ground speed levers are locked in the

START/PARK position.)

• Models with manual parking brake: Make sure

the PTO switch is disengaged, the parking brake is

engaged, and the ground speed control levers are

locked in the START/PARK position.

2. Set the engine speed control past the FAST position to

the CHOKE position.

A warm engine does not require choking.

Some engines are equipped with a separate choke

control.

Some engines are equipped with a ReadyStart

®

feature,

and do not feature a choke.

3. Insert the key into the ignition switch and turn it to

START.

4. After the engine starts, turn off the choke (if equipped),

and warm up the engine by running it for at least a minute

before engaging the PTO switch or driving the rider.

5. After warming the engine, always operate the unit at full

engine speed when mowing.

In the event of an emergency the engine can be stopped

by simply turning the ignition switch to STOP. Use this

method only in emergency situations. For normal engine shut

down follow the procedure given in Stopping The Rider And

Engine .

Stopping the Rider

1. Return the ground speed levers to the middle (or neutral

‘N’) position to stop rider movement. Pivot the levers

outward to lock them in the START/PARK position.

Note:Moving the ground speed levers to the START/ PARK

position automatically engages the parking brake.

2. Disengage the PTO by pushing down on the PTO switch.

3. Move the engine speed control to the SLOW position and

turn the ignition switch to OFF. Remove the key.

Not for

Reproduction

14

Mowing

1. Make sure the PTO switch is disengaged, the ground

speed control levers are locked in their START/PARK

positions, and the operator is in the seat.

2. Start the engine. See Starting the Engine .

3. Set the mower cutting height. See Cutting Height

Adjustment .

4. Set the engine speed control to FAST.

5. Engage the PTO by pulling up on the PTO switch.

6. Pivot the ground speed levers in from the START/PARK

position to the neutral ‘N’ position.

7. Begin mowing. See Operator Safety for tips on safe

mowing practices.

8. When finished, shut off the PTO.

9. Stop the engine. See Stopping The Rider And Engine .

Pushing the Rider By Hand

WARNING

Unsafe Operation Hazard.

DO NOT disengage the transmissions and coast down

slopes. DO NOT use Roll Release to disengage the

transmissions unless machine motion can be controlled and

engine is off.

NOTICE

Do not tow rider.Towing the unit will cause transmission

damage. Do not use another vehicle to push or pull this

unit.

1. Disengage the PTO, lock the ground speed levers into

their START/PARK positions, turn the ignition OFF,

remove the key, and wait for all moving parts to stop.

2. To disengage the transmissions, move the roll release

levers (A or B, Figure6, depending on model), into the

PUSH position as shown.

3. Pivot the ground speed levers in from the START/ PARK

position to the neutral ‘N’ position to disengage the

parking brake. The rider can now be pushed by hand.

4. After moving the rider, re-engage the transmissions

by moving the roll release levers back to the DRIVE

position.

Driving

Zero Turn Driving Practice

Before attempting to drive the zero-turn riding mower make

sure you have read the Features and Controls section

and understand the location and function of all of the unit’s

controls.

The ground speed control levers of this zero-turn riding

mower are responsive, and learning to gain a smooth and

efficient control of the unit’s forward, reverse, and turning

movements will take some practice.

Spending some time going through the maneuvers shown

and becoming familiar with how the unit accelerates, travels,

and steers, before you begin mowing, is absolutely

essential to getting the most out of the zero-turn riding

mower.

Locate a smooth, flat area of your lawn, one with plenty of

room to maneuver. Clear the area of objects, people, and

animals before you begin. Operate the unit at mid-throttle

during this practice session (ALWAYS operate at full throttle

when mowing), and turn slowly to prevent tire slippage and

damage to your lawn.

We suggest you begin with the Smooth Travel procedure,

and then advance through the forward, reverse, and turning

maneuvers.

Smooth Travel

The lever controls of the Zero Turn rider are responsive.

The BEST method of handling the ground speed control

levers is in three steps — as shown in Figure 7.

FIRST place your hands onto the levers as shown.

SECOND, to go forward gradually push the levers forward

with your palms.

THIRD, to speed up move the levers farther forward. To slow

down smoothly, slowly move the levers toward neutral.

Basic Driving

Forward Travel Practice

Gradually move both ground speed control levers — evenly

FORWARD from neutral. Slow down and repeat.

NOTE: Straight forward travel takes practice. If necessary, top

speed can be balance-adjusted — see the Speed Balancing

Adjustment in the Adjustments section near the back of this

manual.

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both ground

speed control levers evenly BACK from neutral. Slow down

and repeat.

NOTE: Practice backing up for several minutes before

attempting to do so near objects. The rider turns sharply in

reverse as well as forward, and backing up straight takes

practice.

Practice Turning Around A Corner

While traveling forward allow one handle to gradually return

back toward neutral. Repeat several times.

NOTE: To prevent pivoting directly on the tire tread, it is best

to keep both wheels going at least slightly forward.

Practice Turning in Place

To turn in place, “Zero Turn,” gradually move one ground

speed control lever forward from neutral and one lever back

from neutral simultaneously. Repeat several times.

Not for

Reproduction

15

NOTE: Changing the amount each lever is pulled—forward or

back, changes the “pivot point” you turn on.

Advanced Driving

Executing an End-Of-Row Zero Turn

Your Zero Turn Rider’s unique ability to turn in place allows

you to turn around at the end of a cutting row rather than

having to stop and Y-turn before starting a new row.

For example, to execute a left end-of row zero turn:

1. Slow down at the end of the row.

2. Move the RIGHT ground speed control lever forward

slightly while moving the LEFT ground speed control lever

back to center and then slightly back from center.

3. Begin mowing forward again.

This technique turns the rider LEFT and slightly overlaps

the row just cut —eliminating the need to back up and re-cut

missed grass.

As you become more familiar and experienced with operating

the Zero Turn rider, you will learn more maneuvers that will

make your mowing time easier and more enjoyable.

Remember, the more you practice, the better your control

of the Zero Turn will be!

Towed Equipment

Secure the trailer with an appropriately sized clevis pin (A,

Figure13) and clip (B). SeeOperator Safetyfor additional

safety information regarding trailers and towing.

WARNING

Towing Hazard

Towed loads can be hazardous and cause loss of control

on slopes.

• The max gross (trailer & load) weight of trailer is 200 lbs

(91kg).

• Do not operate on slope exceeding 5 degrees.

• Reduce speed and use extreme caution on slopes.

Cutting Height Adjustment

The cutting height adjust pedal adjusts the mower cutting

height. SeeSpecificationsfor cutting height adjustment

range.

To adjust cutting height:

1. Fully depress the cutting height adjust pedal (A,

Figure14) until the transport release rod (B) locks the

deck into the highest position (transport position).

2. Remove the pin (C, Figure14) from the adjustment

bracket, and insert it in the desired hole.

Note:Make sure the pin is inserted into the holes in both

upper and lower plates of the adjustment bracket.

3. Depress the cutting height adjust pedal, move the

transport release rod outward, and slowly release the

pedal until it rests against the pin.

Mower Removal And Installation

Refer to the Mower Deck Manual for instructions on removing

and installing the mower deck.

Mower Deck Leveling

Refer to the Mower Deck Manual for instructions on leveling

the mower deck.

Cargo Bed (select models)

The cargo bed is designed to carry up to 50 lbs (22,7 kg).

Slots in the rear of the bed will accommodate a 2 x 4 or 2 x 6

to help secure loads during transport.

WARNING

Amputation Hazard

Rotating blades cut off arms and legs. Do not carry riders

(especially children) even with the blades off. They may fall

off or return for another ride when you are not expecting it.

WARNING

Loss of Control and Roll-Over Hazard

Operating with loads in the cargo bed greater than 50 lbs

can be hazardous and cause loss of control and roll-overs.

The cargo bed can be raised to access the engine

compartment without removing it.

To raise the cargo bed

1. Raise the seat (A, Figure15).

2. Pull up firmly on the rear of the bed (B, Figure15).

3. When lowering the bed, press down firmly to secure the

rear of the bed in place with the locking clips (D).

To remove the cargo bed

1. Remove the pins (C, Figure15) securing the front of the

bed to the rider frame.

2. Pull up firmly on the rear of the bed to release the locking

clips (D, Figure15).

3. Lift and remove the cargo bed from the rider.



CAUTION

To avoid injury, assistance is required when removing or

installing the cargo bed.

To install the cargo bed

1. Position the bed over the engine compartment, aligning

the holes in the front of the bed with the holes in the

frame brackets.

Not for

Reproduction

16

2. Install the pins (C, Figure15) into the holes.

3. Lower the rear of the bed, pressing down firmly to secure

with the locking clips (D, Figure15).

CAUTION

To avoid injury, assistance is required when removing or

installing the cargo bed.

Suspension Adjustment (if equipped)

The shock assemblies (A, Figure16- front shown, rear

similar) can be adjusted to vary the amount of pre-load

applied to the springs. This allows the operator to customize

the ride according to operator’s weight and operating

conditions.

Less Pre-Load:

• Light operator weight

• Softer, more cushioned ride

• Best for relatively flat terrain

More Pre-Load:

• Heavy operator weight

• Stiffer, more rigid ride

• Better handling and greater stability on hilly terrain

To Adjust the Spring Pre-Load:

1. Park machine on a flat, level surface. Disengage the

PTO, pivot the ground speed levers out to the START/

PARK position, and stop the engine.

2. Turn the pre-load adjustment collar (B, Figure16) to a

higher notch (-) to decrease the pre-load, or to a lower

notch (+) to increase the pre-load. Make sure all shocks

are set to the same amount of pre-load.

Maintenance

Maintenance Schedule

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from

the spark plug.

• Disconnect battery at negative terminal (only engines

with electric start).

• Use only correct tools.

• Do not tamper with governor spring, links, or other parts

to increase engine speed.

• Replacement parts must be of the same design and

installed in the same position as the original parts.

Other parts may not perform as well, may damage the

unit, and may result in injury.

• Do not strike the flywheel with a hammer or hard object

because the flywheel may shatter during operation.

TRACTOR AND MOWER

Every 8 Hours or Daily

Check safety interlock system

Clean debris off tractor and mower deck

Clean debris from engine compartment

Every 25 Hours or Annually *

Check mower blade stopping time

Check tractor and mower for loose hardware

Check tire pressure

Every 50 Hours or Annually *

Check tractor brakes

Clean battery and cables

See Dealer Annually to

Lubricate tractor and mower

Check mower blades **

* Whichever comes first

** Check blades more often in regions with sandy soils or high

dust conditions.

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually *

Clean engine air filter and pre-cleaner **

Every 50 Hours or Annually *

Change engine oil

Replace oil filter

Annually

Replace air filter

Replace pre-cleaner

Not for

Reproduction

17

ENGINE

See Dealer Annually to

Inspect muffler and spark arrester

Replace spark plug

Replace fuel filter

Clean engine air cooling system

* Whichever comes first

** Clean more often in dusty conditions or when airborne

debris is present.

Checking Tire Pressures

Tire pressure should be checked periodically (see Figure 17),

and maintained at the levels shown in the Specifications

chart. Note that these pressures may differ slightly from the

"Max Inflation" stamped on the side-wall of the tires. The

pressures shown provide proper traction and extend tire life.

Check Mower Blade Stopping Time

Mower blades and mower drive belt should come to a

complete stop within five seconds after the electric PTO

switch is turned off.

WARNING

Unsafe Operation Hazard

If the mower blade does not come to a complete stop within

5 seconds, the blade must be adjusted. Do not operate the

machine until the proper adjustment has been performed by

an authorized dealer.

Check the mower blade for proper function. See Safety

Interlock System Tests. The blade should stop rotating in 5

seconds or less after moving the blade control to the OFF

position.

Battery Maintenance

WARNING

Explosion and Fire Hazard

When removing or installing battery cables, disconnect the

negative cable FIRST and reconnect it LAST. If not done in

this order, the positive terminal can be shorted to the frame

by a tool.

Cleaning the Battery and Cables

1. Disconnect the cables from the battery, negative cable

first (B, Figure18).

2. Clean the battery terminals and cable ends with a wire

brush until shiny.

3. Reinstall the battery and reattach the battery cables,

positive cable first (A, Figure18).

4. Coat the cable ends and battery terminals with petroleum

jelly or non-conducting grease.

5. Be sure to replace the terminal cover over the positive

battery terminal (A, Figure18).

Charging The Battery

WARNING

Explosion and Fire Hazard

Keep open flames and sparks away from the battery; the

gasses coming from it are highly explosive. Ventilate the

battery well during charging.

A dead battery or one too weak to start the engine may be

the result of a defect in the charging system or other electrical

component. If there is any doubt about the cause of the

problem, see your dealer.

To charge the battery, follow the instructions provided by the

battery charger manufacturer as well as all warnings included

in the Operator Safety section of this manual. Charge the

battery until fully charged. Do not charge at a rate higher than

10 amps.

Seat And Ground Speed Lever

Adjustments

The seat and ground speed levers should be adjusted so

that the ground speed levers can be moved through their full

range of motion without contacting the operator’s legs.

Seat Adjustment

1. Raise the seat.

2. Loosen the adjustment hardware (A or B, Figure19,

depending on seat type) under the seat base.

3. Slide the seat forward or backward to the desired

position.

4. Tighten the hardware to 80 lb-in (9 Nm).

Ground Speed Lever Adjustment

1. Loosen the ground speed lever mounting hardware (A,

Figure20) to adjust the levers forward and backward.

2. Remove the hardware to raise or lower the levers.

3. Always be sure to adjust both levers so that they are

aligned (B, Figure20).

4. After adjustment is complete, tighten the hardware to 13

lb-ft (18 Nm).

Speed Balancing (Tracking) Adjustment

If the rider drifts to the right or left when the ground speed

levers are in the maximum forward position, the top speed of

each of these levers can be balanced. Only adjust the speed

of the wheel that is traveling faster.

1. Tighten the knob (A, Figure21) of the faster wheel by 1/2-

turn (clockwise) increments until the rider travels (tracks)

straight.

WARNING

Unsafe Operation Hazard

Not for

Reproduction

18

DO NOT adjust the rider for a faster overall speed

forward or reverse than it was designed.

Changing The Oil

Used oil is a hazardous waste product and must be disposed

of properly. Do not discard with household waste. Check

with your local authorities, service center, or dealer for safe

disposal/recycling facilities.

Draining The Oil

1. With engine off but still warm, disconnect the spark plug

wire (A, Figure22) and keep it away from the spark plug.

2. Remove the dipstick (B, Figure22).

Standard Oil Drain Plug

1. Remove the oil drain plug (C, Figure22). Drain the oil into

an approved container.

2. After the oil has drained, install and tighten the oil drain

plug.

Optional Quick Oil Drain

1. Disconnect the oil drain hose (H, Figure23) from the side

of the engine.

2. Turn and remove the oil drain cap (I, Figure23). Carefully

lower the quick oil drain (H) into an approved container

(J).

3. After the oil has drained, install the oil drain cap. Attach

the oil drain hose to the side of the engine.

Changing The Oil Filter

For replacement intervals, see Maintenance Schedule.

1. Drain the oil from the engine. See Draining The Oil .

2. Remove the oil filter (K, Figure 24) and dispose of

properly.

3. Before installing the new oil filter, lightly lubricate the oil

filter gasket with fresh, clean oil.

4. Install the oil filter by hand until the gasket contacts the oil

filter adapter, then tighten the oil filter 1/2 to 3/4 turns.

5. Add oil. See Operation - Check Oil Level .

6. Start and run the engine. As the engine warms up, check

for oil leaks.

7. Stop the engine and check the oil level.

Servicing The Air Filter

WARNING

Fire and Explosion Hazard

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

• Never start or run the engine with the air cleaner

assembly or air filter removed.

NOTICE

Do not use pressurized air or solvents to clean the filter.

Pressurized air can damage the filter and solvents will

dissolve the filter.

1. Loosen the fasteners (A, Figure25) and remove the

cover (B).

2. To remove the filter (C, Figure25), lift the end of the

filter.

3. Remove the pre-cleaner (D, Figure25), if equipped, from

the filter.

4. To loosen debris, gently tap the filter on a hard surface. If

the filter is excessively dirty, replace with a new filter.

5. Wash the pre-cleaner in liquid detergent and water. Then

allow it to thoroughly air dry. Do not oil the precleaner.

6. Assemble the dry pre-cleaner to the filter.

7. Install the filter into the engine base (E, Figure25) and

push down until the filter snaps in place.

8. Install the cover.

Cleaning

1. Clean dirt and debris from the rider and mower deck.

Note:Some mower decks feature a washout port. See

Washing The Mower Deck .

2. Clean any debris buildup in the engine compartment and

from on or around the engine.

WARNING

Fire Hazard

Yard debris is combustible.

• Clean dirt and debris from the rider and mower deck.

• Clean build-up from around the engine.

Washing The Mower Deck

The washout port allows you to connect a typical garden hose

to the left-hand side of the mower deck to remove grass and

debris from the underside.

WARNING

Amputation and Thrown Object Hazard

Contact with the mower blades, or with objects thrown by

the mower blades, could result in death or serious injury.

• Before running the mower, make sure the hose is

properly connected and does not come into contact with

the blades.

• When the mower is running and the blades are

engaged, the person cleaning the mower deck must be

in the operator position, with no bystanders in the area.

1. Place the unit on a smooth level surface.

2. Attach the quick disconnect (C, Figure26) to garden hose

(B) and connect to the washout port (A) on the mower

deck.

Not for

Reproduction

19

3. Run water to remove grass and debris from the underside

of the mower deck.

4. Turn the mower on and place in the highest cutting

position.

5. Turn the mower off.

6. Remove the garden hose and quick disconnect from the

washout port when completed.

Storage

WARNING

Fire and Explosion Hazard

Never store the unit (with fuel) in an enclosed, unventilated

structure. Fuel vapors can travel to an ignition source (such

as a furnace, water heater, etc.) and cause an explosion.

Fuel vapor is also toxic to humans and animals.

When Storing Fuel Or Equipment With Fuel in Tank

• Store away from furnaces, stoves, water heaters, or

other appliances that have pilot lights or other ignition

sources because they can ignite fuel vapors.

Equipment

Disengage the PTO, lock the ground speed levers in the

START/PARK position, and remove the key.

Battery life will be increased if it is removed. Put in a cool, dry

place and keep fully charged during storage. If the battery is

left in the unit, disconnect the negative cable.

Fuel System

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system

or on essential carburetor parts. To keep fuel fresh, use

Briggs & Stratton® Advanced Formula Fuel Treatment

& Stabilizer, available wherever Briggs & Stratton genuine

service parts are sold.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system. The engine and fuel can then be stored up to 24

months.

If gasoline in the tank has not been treated with a fuel

stabilizer, it must be drained into an approved container.

Run the engine until it stops from lack of fuel. The use of a

fuel stabilizer in the storage container is recommended to

maintain freshness.

Engine Oil

While the engine is still warm, change the engine oil.

Before starting the unit after it has been stored:

• Check all fluid levels. Check all maintenance items.

• Perform all recommended checks and procedures found

in this manual.

• Allow the engine to warm up for several minutes before

use.

Troubleshooting

Troubleshooting The Rider

PROBLEM LOOK FOR REMEDY

Ground speed levers

not in START/PARK

positions.

Lock ground speed

levers in START/ PARK

positions.

PTO (electric clutch)

switch in ON position.

Place in OFF position.

Out of fuel. If engine is hot, allow

it to cool, then refill the

fuel tank.

Fuel valve closed (if

equipped).

Open fuel valve.

Engine flooded. Open the choke (if

equipped).

Gas is old or stale. Drain fuel and replace

with fresh fuel.

Battery terminals

require cleaning.

Clean the battery

terminals.

Battery discharged or

dead.

Recharge or replace.

Spark plug(s) faulty,

fouled or incorrectly

gapped.

Clean and gap or

replace.

Engine will not turnover

or start.

Water in fuel. Drain fuel and refill with

fresh fuel.

Fuel mixture too rich. Clean air filter. Check

the choke (if equipped).

Spark plug faulty,

fouled, or incorrectly

gapped.

Clean and gap or

replace.

Engine starts hard or

runs poorly.

Fuel filter dirty. Replace fuel filter.

Low oil level. Check/add oil as

required.

Engine knocks.

Using wrong grade oil. See Oil

Recommendations .

Engine running too hot. Check engine fins,

blower screen, and air

cleaner.

Using wrong grade oil. See Oil

Recommendations .

Excessive oil

consumption.

Too much oil in

crankcase.

Drain excess oil.

Dirty air filter. Replace air filter.Engine exhaust is black.

Engine choke control is

in closed position.

Open choke control (if

equipped).

Engine runs, but rider

will not drive.

Transmission(s)

disengaged.

Unlock roll release

lever(s).

Rider drive belt slips. Pulleys or belt greasy or

oily.

Clean as required.

Rider steers or handles

poorly.

Steering linkage is

loose.

Check and tighten any

loose connections.

For all other issues, see authorized dealer.

Troubleshooting The Mower

PROBLEM LOOK FOR REMEDY

Mower will not raise. Mower deck not

properly installed.

SeeMower Removal

And Installation.

Not for

Reproduction

20

PROBLEM LOOK FOR REMEDY

Mower not leveled

properly.

SeeMower Deck

Leveling.

Mower cut is uneven.

Rider tires not inflated

equally or properly.

SeeMaintenancesection.

Engine speed too slow. Set engine speed

control to FAST.

Mower cut is rough

looking.

Ground speed too fast. Decrease ground

speed.

Engine speed too slow. Set engine speed

control to FAST.

Ground speed too fast. Decrease ground

speed.

Cutting height set too

low.

Cut tall grass at

maximum cutting height

during first pass.

Engine stalls easily with

mower engaged.

Discharge chute

jamming with cut grass.

Cut grass with

discharge pointing

toward previously cut

area.

Excessive mower

vibration.

Blade mounting

hardware is loose.

Tighten to 50-60 ft-lbs

(68-81 Nm).

For all other issues, see authorized dealer.

Specifications

ENGINE

Briggs & Stratton

Intek™ Series

Displacement 44.18 cu in. (724 cc)

Professional Series™

Displacement 44.18 cu in. (724 cc)

All Engines

Oil Capacity 64 oz (1,9 L)

Spark Plug Gap 0.030 in. (0,76 mm)

Spark Plug Torque 180 in-lbs (20 Nm)

CHASSIS

Fuel Tank Capacity 3 gal (11,4 L)

Inflation Pressure

- Front Wheels 22 psi (1,52 bar)

- Rear Wheels 12 psi (0,83 bar)

TRANSMISSION

Hydro-Gear® EZT®Type

Hydro-Gear® ZT-2800®

MOWER

42” (107 cm)

44” (112 cm)

46” (117 cm)

48” (122 cm)

Width of Cut

52” (132 cm)

1.5” - 3.75” (3,8 - 9,5 cm)Cutting Height

1.5” - 4.5” (3,8 - 11,7 cm)

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive

Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque

values are derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower

values are derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power

values are taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments.

Actual gross engine power will be higher than net engine power and is affected by, among other things, ambient operating

conditions and engine-to-engine variability. Given the wide array of products on which engines are placed, the gasoline engine

may not develop the rated gross power when used in a given piece of power equipment. This difference is due to a variety

of factors including, but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor,

fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine

variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for

this engine.

Note:The engine information contained in this manual applies

to Briggs & Stratton engines only. For information regarding

non-Briggs engines, refer to the engine manual supplied with

your unit.

Parts And Accessories

See an Authorized Service Dealer.

Sayfa yükleniyor...

Simplicity 2691359-00 Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Simplicity 2691359-00 Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler