imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Digital Home
Entertainment System
user manual
HT-F450
HT-F453
HT-F455
HT-F450-XU-11-26.indd 1HT-F450-XU-11-26.indd 1 2013-3-12 8:49:212013-3-12 8:49:21
|
2 English
Safety Information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous
voltage” inside the product that
presents a risk of electric shock or
personal injury.
CAUTION: TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY
INSERT.
This symbol indicates important
instructions accompanying the
product.
Wiring the Main Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is
indicated on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be
used. Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must
be of the same colour as the fuse fitted in the plug. Replacement covers are available from your dealer. If the fitted plug
is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should
obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative
to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains socket
as there is a risk of shock hazard from the bared flexible cord. Never attempt to insert bare wires directly into a mains
socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as
follows:–The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or
BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or
RED.
WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH LETTER
E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
WARNING
• To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
CAUTION
• Apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
• The Mains plug is used as a disconnect device and
shall stay readily operable at any time.
• This apparatus shall always be connected to an AC
outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug
must be pulled out from the mains socket, therefore
the mains plug shall be readily operable.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
CAUTION
• INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO
BEAM.
HT-F450-XU-11-26.indd 2HT-F450-XU-11-26.indd 2 2013-3-12 8:50:392013-3-12 8:50:39
English 3
|
01 Safety Information
Disc Storage & Management
• Holding Discs
- Fingerprints or scratches on
a disc may reduce sound and
picture quality or cause skipping.
- Avoid touching the surface of a disc where data has
been recorded.
- Hold the disc by the edges so that fingerprints will
not get on the surface.
- Do not stick paper or tape on the
disc.
• Cleaning Discs
- If you get fingerprints or dirt on a disc,
clean it with a mild detergent diluted
in water and wipe with a soft cloth.
- When cleaning, wipe gently from the inside to the
outside of the disc.
- Disc Storage
Do not keep in direct sunlight.
Keep in a cool ventilated area.
Keep in a clean protection jacket and store
vertically.
Licence
• ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX,LLC,a subsidiary of Rovi Corporation.
This is an official DivX Certified® device that plays DivX
video. Visit divx.com for more information and software
tools to convert your files into DivX videos.
• ABOUT DIVX VIDEO-ON-DEMAND: This DivX
Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies. To
obtain your registration code, locate the DivX VOD
section in your device setup menu. Go to vod.divx.
com for more information on how to complete your
registration.
• DivX Certified® to play DivX® video, including premium
content.
• DivX®, DivX Certified® and associated logos are
trademarks of Rovi Corporation or its subsidiaries and
are used under license.
• Covered by one or more of the following U.S. patents :
7,295,673; 7,460,668; 7,515,710; 7,519,274.
• Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
• HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other
countries.
• This item incorporates copy protection technology
that is protected by U.S. patents and other intellectual
property rights of Rovi Corporation. Reverse
engineering and disassembly are prohibited.
• This product uses some software programs which are
distributed under the Independent JPEG Group.
• This product uses some software programs which are
distributed under the OpenSSL Project.
Copyright
© 2013 Samsung Electronics Co., Ltd. All rights reserved.
Copy Protection
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your product
directly to your TV, not to a VCR. Connecting to a VCR
results in a distorted picture from copy-protected DVD
discs.
HT-F450-XU-11-26.indd 3HT-F450-XU-11-26.indd 3 2013-3-12 8:50:422013-3-12 8:50:42
|
4 English
Contents
SAFETY INFORMATION
2 Safety Warnings
3 Disc Storage & Management
3 Licence
3 Copyright
3 Copy Protection
GETTING STARTED
5 Disk and Format Compatibility
6 Notes on the USB connection
6 Accessories
7 Front Panel
7 Rear Panel
8 Remote control
CONNECTIONS
10 Connecting the Speakers
12 Connecting to a TV
13 Connecting to External Devices
SETTINGS
14 The Initial Settings Procedure
14 Accessing the Settings Screen
14 Display
14 TV Aspect
14 BD Wise
15 Resolution
15 HDMI Format
15 Video Out Signal
15 Audio
15 Simple Setup
15 Speaker Setting
15 DRC (Dynamic Range Compression)
15 AUDIO SYNC
15 Speaker Selection
16 User EQ
16 Audio Return Ch.
16 System
16 Initial Settings
16 DivX(R) Registration
16 DivX(R) Deactivation
16 Language
16 Security
16 Parental Rating
16 Change Password
16 Support
16 Product Information
BASIC FUNCTIONS
17 Disc Playback
17 Audio CD(CD-DA)/MP3/WMA Playback
17 JPEG File Playback
17 Using the Playback Function
19 Using the Special Remote Control
Buttons
20 Listening to Radio
21 USB Function
21 USB Recording
OTHER INFORMATION
22 Troubleshooting
23 Specifications
25 OpenSSL License
Figures and illustrations in this User Manual
are provided for reference only and may differ
from actual product appearance.
An administration fee may be charged if either
a. an engineer is called out at your request and
there is no defect in the product (i.e. where
you have failed to read this user manual)
b. you bring the unit to a repair centre and
there is no defect in the product (i.e. where
you have failed to read this user manual).
The amount of such administration charge will
be advised to you before any work or home
visit is carried out.
HT-F450-XU-11-26.indd 4HT-F450-XU-11-26.indd 4 2013-3-12 8:50:452013-3-12 8:50:45
English 5
|
02 Getting Started
Getting Started
Disk and Format Compatibility
Disc types and contents your product
can play
Media Term Disc Type
VIDEO
DVD
DVD-Video or DVD±R/±RW
discs
CD
Data CD (CD DA, CD-R/-
RW)
DivX DVD±R/±RW, CD-R/-RW
MUSIC MP3 CD-R/-RW
PHOTO JPEG CD-R/-RW
Disc types your product cannot play
• LD, CD-G/-I/-ROM, DVD-ROM/-RAM
| NOTE |
DVD discs purchased abroad may not play on this
product.
This product may not respond to all operating
commands because some DVD, and CD discs allow
specific or limited operation and provide only certain
features during playback. Please note that this is not a
defect in the product.
Samsung cannot guarantee that this product will play
every disc bearing the DVD or CD logo because disc
formats evolve, and problems and errors may occur
during the creation of DVD, and CD software and/or
the manufacture of discs.
Please contact the SAMSUNG Customer Care Centre,
if you have questions or encounter difficulty when
playing DVD, or CD discs in this product. Also, refer to
rest of this user manual for additional information on
playback restrictions.
Some commercial discs and DVD discs purchased
outside your region may not play on this product.
This product does not support DTS sound.
Supported Formats
Video File Support
Format Supported Versions
AVI
DivX3.11~DivX6.8
WMV
V1/V2/V3/V7
Music File Support
Format Bit Rate
Sampling
Frequency
MP3
80~320kbps
44.1khz
WMA
56~128kbps
AC3
128~384kbps 44.1/48khz
• Aspect Rtio : This product supports up to 720x576
pixels. TV screen resolutions higher than 800 will not
be supported.
• When you play a disc whose sampling frequency is
higher than 48khz or 320kbps, you may experience
shaking on the screen during playback.
• Sections with a high frame rate might not be played
while playing a DivX file.
• Since this product only provides encoding formats
authorized by DivX Networks, Inc., a DivX file created
by the user might not play.
Logos of Discs the product can play
DVD-VIDEO AUDIO-CD DivX
Region Code
Both products and discs are coded by region. These
regional codes must match for a disc to play. If the codes
do not match, the disc will not play. The Region Number
for this product is displayed on the rear panel of the
product.
HT-F450-XU-11-26.indd 5HT-F450-XU-11-26.indd 5 2013-3-12 8:50:472013-3-12 8:50:47
|
6 English
Getting Started
Disc Type
Region
Code
Area
DVD-VIDEO
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle
East, Egypt, Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
5
Russia, Eastern Europe, India,
North Korea, Mongolia
6
China
| NOTE |
If the Region number of a DVDs does not correspond
to the Region number of this product, the product
cannot play the disc.
Notes on the USB connection
• Supported devices: USB storage media, MP3 player,
digital camera
• If a folder or file name is longer than 10 characters, it
may not properly display or operate.
• A subtitle file bigger than 300KB may not be properly
displayed.
• A certain USB/digital camera device, USB card reader
is not supported.
• FAT16 and FAT32 file systems are supported.
• Connect directly to the product's USB port.
Connecting through another cable may raise problems
with USB compatibility.
• Inserting more than one memory device to a multi-card
reader may not operate properly.
• PTP protocol for digital camera is not supported.
• Do not disconnect USB device during a "Reading"
process.
• Bigger the image resolution, the longer the delay to
displaying.
• DRM applied MP3/WMA or video files downloaded
from a commercial site are not played back.
• External HDD device is not supported.
• The maximum current supported by the USB port for
an external device is 500 mA (at 5V DC).
• Supported file formats
Format
Still
Picture
Music Movie
File name
JPG MP3 WMA WMV DivX
File
extension
JPG .JPEG .MP3 .WMA .WMV .AVI
Bit rate
–
80~320
kbps
56~128
kbps
4Mbps 4Mbps
Version
––V8
V1,V2,
V3,V7
DivX3.11~
DivX6.8
Pixel
640x480 – – 720x576
Sampling
Frequency
– 44.1kHz 44.1kHz 44.1KHz~ 48KHz
| NOTE |
Playing back a JPEG file whose image resolution is
higher than that of DVD may result in degraded image
quality when displayed.
Accessories
Check for the supplied accessories below.
Video Cable FM Cable
FUNCTION
MUTE
TOOLS
RETURN
EXIT
INFO
MO/ST
REPEATSLEEP
S.VOL P.BASS
USB REC
S/W LEVEL
1
2
3
4
56
7
8
0
9
RECEIVER
FOOTBALL
DSP/EQV-SURROUND
DVD TV
TUNER
MEMORY
DIMMER
ABCD
VOL
TUNING
/ CH
TV
SOURCE
HOME
TITLE MENU
DISC MENU
TV SOUND
GIGA
User manual
Remote Control/Batteries
(AAA size)
HT-F450-XU-11-26.indd 6HT-F450-XU-11-26.indd 6 2013-3-12 8:50:502013-3-12 8:50:50
English 7
|
02 Getting Started
Front Panel
AUX IN 1
5V 500mA
DISC TRAY DISPLAY
OPEN/CLOSE (
)
VOLUME CONTROL (
, )
REMOTE CONTROL
SENSOR
FUNCTION (
)
USB HOST
STOP (
)
PLAY/PAUSE ( )
POWER ( )
* AUX IN 1
CONNECTOR
* Connecting Audio from External Components
Connect an Audio cable (not supplied) from the AUX IN 1 jack on the front of the product to the Audio Out jack on
your MP3 player.
Select the AUX 1 mode.
Rear Panel
AUX IN 2
HDMI OUT
EXTERNAL DIGITAL
AUDIO IN (OPTICAL)
* FM ANTENNA
SPEAKER OUTPUT
CONNECTORS
COOLING FAN
FA NET
(Only for Service)
VIDEO OUT
FM ANT
DIGITAL
AUDIO IN
OPTICAL
SURROUND SUBWOOFER SURROUND
SPEAKERS OUT
HDMI OUT
AUX IN 2
VIDEO
OUT
FA NET
(Only For Service)
* Connecting the FM Antenna
1 .
Connect the FM antenna supplied to the FM ANTENNA Jack.
2 .
Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or
other rigid surface.
| NOTE |
Ensure a minimum of 10 cm of clear space on all sides of the home cinema to ensure adequate ventilation. Do not
obstruct the cooling fan or ventilation holes.
This product does not receive AM broadcasts.
HT-F450-XU-11-26.indd 7HT-F450-XU-11-26.indd 7 2013-3-12 8:51:012013-3-12 8:51:01
|
8 English
Getting Started
Remote Control
Tour of the Remote Control
FUNCTION
MUTE
TOOLS
RETURN
EXIT
INFO
MO/ST
REPEATSLEEP
S.VOL P.BASS
USB REC
S/W LEVEL
1
2
3
4
56
7
8
0
9
RECEIVER
FOOTBALL
DSP/EQV-SURROUND
DVD TV
TUNER
MEMORY
DIMMER
ABCD
VOL
TUNING
/ CH
TV
SOURCE
HOME
TITLE MENU
DISC MENU
TV SOUND
GIGA
To open and close the disc tray.
Turn the product on and off.
If you want to change to Home
Theater, press the DVD button.
Press numeric buttons to operate
options.
To select the football mode.
This is mode selection button.
or
Press to select TV's video mode.
Select MONO or STEREO for radio
broadcasting.
Press to skip backwards or
forwards.
Press to search backwards or
forwards.
Press to pause a disc.
Adjust the volume.
Search for active FM stations and
change channels.
Cut off the sound temporarily.
Audio signal can output to Home
Theater Speaker or TV Speaker.
Allows you to repeat a title, chapter,
track or disc.
Press to check the disc menu.
Brings up the product's setup menu.
Return to the previous menu.
Press this to exit the menu.
Display current disc(file) status.
Allow access to common functions
of the DVD Home Theater such as
navigating the Photo List.
Use this to enter the Title menu.
Press Virtual Surround to select On/
Off.
Used to change the audio/subtitle
language, angle etc.
Adjust the brightness of Display.
Pr
ess to preset FM stations.
If you want to change to TV mode,
press the TV button.
Press to stop/play a disc.
Select the desired P.BASS.
Used to adjust the level of the
subwoofer.
Used to start USB recording.
Select the desired DSP/EQ audio
mode.
Select on-screen menu items and
change menu value.
Used to turn on/off GIGA Sound
function.
Regulate and stabilize the volume
level against a drastic volume change.
Set a Sleep time to shut off the
Product.
HT-F450-XU-11-26.indd 8HT-F450-XU-11-26.indd 8 2013-3-12 8:51:052013-3-12 8:51:05
English 9
|
02 Getting Started
Installing batteries in the Remote
Control
Battery size: AAA
| NOTE |
Make sure to match the “+” and “–” ends of the
batteries with the diagram inside the compartment.
Assuming typical TV usage, the batteries last for about
one year.
The remote control can be used up to approximately
7 meters from the product in a straight line.
Setting the Remote Control
You can control certain functions of your TV with this
remote control.
When operating a TV with the remote control
1 .
Press the TV button to set the remote control to TV
mode.
2 .
Press the POWER button to turn on the TV.
3 .
While holding down the POWER button, enter the
code corresponding to your brand of TV.
• If there is more than one code listed for your TV in
the table, enter one at a time to determine which
code works.
• Example : For a Samsung TV
While holding down the POWER button, use the
number buttons to enter 00, 15, 16, 17 and 40.
4 .
If the TV turns off, the setting is complete.
• You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
| NOTE |
The remote control may not work or some operations
may not be possible with some brands of TVs.
The remote control will work on a Samsung TV by
default.
TV Control Codes
Brand Code Brand Code
Admiral
(M.Wards)
56, 57, 58 MTC 18
A Mark 01, 15 NEC 18, 19, 20, 40, 59, 60
Anam
01, 02, 03, 04, 05, 06,
07, 08, 09, 10, 11, 12,
13, 14
Nikei 03
AOC 01, 18, 40, 48 Onking 03
Bell & Howell
(M.Wards)
57, 58, 81 Onwa 03
Brocsonic 59, 60 Panasonic
06, 07, 08, 09, 54, 66,
67, 73, 74
Candle 18 Penney 18
Cetronic 03 Philco
03, 15, 17, 18, 48, 54,
59, 62, 69, 90
Citizen 03, 18, 25 Philips
15, 17, 18, 40, 48, 54,
62, 72
Cinema 97 Pioneer 63, 66, 80, 91
Classic 03 Portland 15, 18, 59
Concerto 18 Proton 40
Contec 46 Quasar 06, 66, 67
Coronado 15 Radio Shack 17, 48, 56, 60, 61, 75
Craig 03, 05, 61, 82, 83, 84 RCA/Proscan
18, 59, 67, 76, 77, 78,
92, 93, 94
Croslex 62 Realistic 03, 19
Crown 03 Sampo 40
Curtis Mates 59, 61, 63 Samsung
00, 15, 16, 17, 40, 43,
46, 47, 48, 49,
CXC 03 Sanyo 19, 61, 65
Daewoo
02, 03, 04, 15, 16, 17,
18, 19, 20, 21, 22, 23,
24, 25, 26, 27, 28, 29,
30, 32, 34, 35, 36, 48,
59, 90
Scott 03, 40, 60, 61
Daytron 40 Sears 15, 18, 19
Dynasty 03 Sharp 15, 57, 64
Emerson
03, 15, 40, 46, 59, 61,
64, 82, 83, 84, 85
Signature 2000
(M.Wards)
57, 58
Fisher 19, 65 Sony 50, 51, 52, 53, 55
Funai 03 Soundesign 03, 40
Futuretech 03 Spectricon 01
General Electric
(GE)
06, 40, 56, 59, 66, 67,
68
SSS 18
Hall Mark 40 Sylvania 18, 40, 48, 54, 59, 60, 62
Hitachi 15, 18, 50, 59, 69 Symphonic 61, 95, 96
Inkel 45 Tatung 06
JC Penny 56, 59, 67, 86 Techwood 18
JVC 70 Teknika 03, 15, 18, 25
KTV 59, 61, 87, 88 TMK 18, 40
KEC 03, 15, 40 Toshiba 19, 57, 63, 71
KMC 15 Vidtech 18
LG (Goldstar)
01, 15, 16, 17, 37, 38,
39, 40, 41, 42, 43, 44
Videch 59, 60, 69
Luxman 18 Wards
15, 17, 18, 40, 48, 54,
60, 64
LXI (Sears)
19, 54, 56, 59, 60, 62,
63, 65, 71
Yamaha 18
Magnavox
15, 17, 18, 48, 54, 59,
60, 62, 72, 89
York 40
Marantz 40, 54 Yupiteru 03
Matsui 54 Zenith 58, 79
MGA 18, 40 Zonda 01
Mitsubishi/MGA 18, 40, 59, 60, 75 Dongyang 03, 54
HT-F450-XU-11-26.indd 9HT-F450-XU-11-26.indd 9 2013-3-12 8:51:112013-3-12 8:51:11
|
10 English
Connections
This section involves various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward
you. Place the speakers so that their tweeters will be at the same height as your ear. Align
the front face of the front speakers with the front face of the center speaker or place them
slightly in front of the center speakers.
Centre Speaker
It is best to install it at the same height as the front speakers. You can also install it directly
over or under the TV.
Surround
Speakers
Place these speakers to the side of your listening position. If there isn't enough room, place
these speakers so they face each other. Place them about 60 to 90cm above your ear,
facing slightly downward.
* Unlike the front and center speakers, the surround speakers are used to handle mainly
sound effects and sound will not come from them all the time.
Subwoofer
The position of the subwoofer is not so critical. Place it anywhere you like.
| CAUTION |
Do not let children play with or near the speakers. They could get hurt if the speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.
Keep the subwoofer out of the reach of children so as to prevent them from inserting their hands or alien substances
into the duct (hole) of the subwoofer.
Do not hang the subwoofer on the wall through the duct (hole).
| NOTE |
If you place a speaker near your TV set, screen colour may be distorted because of the magnetic field generated by
the speaker. If this occurs, place the speaker away from your TV set.
Position of the product
Place it on a stand or cabinet shelf, or under the TV stand.
Selecting the Listening Position
The listening position should be located about 2.5 to 3 times the distance of the TV's screen size away from the TV.
Example : For 32" TV's 2~2.4m
For 55" TV's 3.5~4m
Front (L)
Front (L)
Surround (L)
Surround (L)
Surround (R)
Surround (R)
Front (R)
Front (R)
Product
Product
Centre
Centre
Subwoofer
Subwoofer
Normal speaker's position :
Simple speaker's position :
HT-F450-XU-11-26.indd 10HT-F450-XU-11-26.indd 10 2013-3-12 8:51:142013-3-12 8:51:14
English 11
|
03 Connections
Installing the Speakers on the Tallboy Stand
* HT-F453 only - Front Speakers
* HT-F455 only - Front/Surround Speakers
1 .
Turn the Stand Base upside-down and connect it to the
Stand.
2 .
Use the driver to combine the screws on the 3 marked
holes.
| CAUTION |
When you use a torque screwdriver, be careful not to put
excessive force. Otherwise, it runs idle or can be damaged.
(torque screwdriver- below 15 kg.f.cm)
3 .
Straighten a supplied speaker wire to the gravity direction
and put in the hole on the center of Stand Base.
4 .
Connect the upper Speaker to the assembled Stand.
5 .
Insert a screw clockwise into the hole on the rear of the
speaker using a screwdriver. And then connect a speaker
cable.
6 .
This is the appearance after the speaker is installed.Follow
this steps to install other speaker.
Speaker Components
FRONT
CENTER
FRONT FRONT SURROUNDSTAND
SCREW (5×20): 8EA SCREW (5×20): 16EA
(L) (R) (L) (R) (L) (R)
SURROUND
SUBWOOFER
HT-F450
HT-F453 HT-F455
STAND
STAND BASE
STAND BASE
SURROUND
SPEAKER CABLE
(L) (R)
2
4
1
3
5 6
Stand Base
Stand
Speaker
Stand
(L) (R) (L) (R)
HT-F450-XU-11-26.indd 11HT-F450-XU-11-26.indd 11 2013-3-12 8:51:182013-3-12 8:51:18
|
12 English
Connections
Connecting The Speakers
1 .
Press down the terminal tab on the back of the speaker.
2 .
Insert the black wire into the black terminal (–) and the red wire into the red terminal (+), and then release the tab.
3 .
Connect the connecting plugs to the back of the product by matching the colours of the speaker plugs to the
speaker jacks.
In case of HT-F450
FM ANT
DIGITAL
AUDIO IN
OPTICAL
SURROUND SUBWOOFER SURROUND
SPEAKERS OUT
HDMI OUT
AUX IN 2
VIDEO
OUT
FA NET
(Only For Service)
VOLTAGE
SEL
115
Front Speaker (R)
Subwoofer
Surround Speaker (R) Surround Speaker (L)
Center Speaker
Front Speaker (L)
Refer to page 11 for the speakers of
HT-F453/HT-F455.
Black
Red
Connecting to a TV
Select either Method 1 or Method 2.
• If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote
control, and then select the correct external source from the TV's source list (HDMI, Video In, etc.) to view video
from the home cinema.
FM ANT
DIGITAL
AUDIO IN
OPTICAL
SURROUND SUBWOOFER SURROUND
SPEAKERS OUT
HDMI OUT
AUX IN 2
VIDEO
OUT
Method 1
Method 2
(Cable not supplied.)
Method 1 Connecting to a TV with an HDMI Cable - Best Quality (Recommended)
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN jack on your
TV.
HT-F450-XU-11-26.indd 12HT-F450-XU-11-26.indd 12 2013-3-12 8:52:082013-3-12 8:52:08
English 13
|
03 Connections
Method 2 Connecting to a TV with a Video Cable - Good Quality
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN jack on your TV.
| NOTE |
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection
systems and the picture will be distorted on the television.
Using Anynet+(HDMI-CEC) (Samsung products only)
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's remote control.
Anynet + can be used by connecting this product to a SAMSUNG TV using a HDMI Cable.
| NOTE |
The Anynet+ function supports some buttons of the remote control.
This function is not available if an HDMI cable does not support CEC.
Please check the Anynet+ logo (If your TV has an Anynet+ logo, then it supports Anynet+ function.)
Connecting to External Devices
To select the correct mode for an external device, press the FUNCTION button. Each time you press the button, the
mode changes in this order : DVD/CD
D.IN
AUX 1
AUX 2
USB
FM
R
Red
W
White
Method 1
Method 2
External Devices
(Cable not supplied.)
(Cable not supplied.)
FM ANT
DIGITAL
AUDIO IN
OPTICAL
HDMI OUT
AUX IN 2
VIDEO
OUT
AUDIO OUT
DIGITAL OUT
Method 1 AUX 2 : Connecting an External Analog Component
Connect AUX IN 2 (Audio) on the back of the product to the Audio Out of the external Analog component.
Select the AUX 2 mode.
| NOTE |
Be sure to match the colors of the connecting jacks.
You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of the VCR to
this product.
If no button actions for more than 8 hours in AUX mode, the power will automatically turn off.
Method 2 OPTICAL : Connecting an External Digital Audio Component
Connect the DIGITAL AUDIO IN (OPTICAL) on the back of the product to the Digital Output of the external digital
component.
Select the D.IN mode.
If no OPTICAL signal for more than 25 minutes, the product will automatically turn off.
HT-F450-XU-11-26.indd 13HT-F450-XU-11-26.indd 13 2013-3-12 8:52:132013-3-12 8:52:13
|
14 English
Settings
The Initial Settings Procedure
Press the POWER button when it is plugged in TV for the
first time. Initial Settings screen will be displayed.
▲▼ (select the desired language)
E
▲▼ (select the desired TV Aspect)
E
▲▼ (select the simple speaker setup)
E
.
>
Move
"
Select
Initial settings > On-Screen Language
Select a language for the on-screen displays
English
Nederlands
Français
Deutsch
Italiano
| NOTE |
The initial screen may appear different, depending on
the content of the disc.
If the HDMI cable is connected to the product, TV
aspect does not appear.
If you want to display the Initial Setting screen again
and make changes, select the Reset option.
Depending on your TV, certain HDMI output
resolutions may not work. Please refer to the user
manual of your TV.
Accessing the Settings Screen
1 .
Press the POWER button.
Function DVD/CD
Settings
2 .
Press the ◄► buttons to select Settings, then
press the
E
button. The Settings screen appears.
3 .
To access the menus, sub-menus, and options
on the Settings screen, please refer to the remote
control illustration below.
Buttons on the Remote Control Used
for the Settings Menu
TOOLS
RETURN
EXIT
INFO
HOME
TITLE MENU
DISC MENU
1
24
3
1
HOME Button : Press to move to the Home
screen.
2
RETURN Button : Return to the previous menu.
3
E
(Enter) / DIRECTION Button :
• Press ▲▼◄► to move the cursor or select
an item.
• Press the
E
button to activate the currently
selected item or confirm a setting.
4
EXIT Button : Press to exit the current menu.
Display
TV Aspect
• 4:3 Pan-Scan: Select when you want to see the 16:9
video supplied by the DVD without the black bars on
top and bottom, even though you have a TV with a 4:3
ratio screen.
• 4:3 Letter Box: Select when you want to see the total
16:9 ratio screen DVD supplies, even though you have
a TV with a 4:3 ratio screen. Black bars will appear at
the top and bottom of the screen.
• 16:9 Wide: You can view the full 16:9 picture on your
widescreen TV.
BD Wise
BD Wise is Samsung’s latest inter-connectivity feature.
When you connect a Samsung product and a Samsung
TV with BD Wise to each other via HDMI, and BD Wise is
on in both the product and TV, the product outputs video
at the video resolution and frame rate of the DVD Disc.
| NOTE |
This will optimize the picture quality according to the
content (In the DVD disc, etc) that you want to play
and the product or your BD Wise-compliant Samsung
TV.
HT-F450-XU-11-26.indd 14HT-F450-XU-11-26.indd 14 2013-3-12 8:52:172013-3-12 8:52:17
English 15
|
04 Settings
If you want to change the resolution in BD Wise mode,
you must set BD wise mode to Off in advance.
BD Wise will be disabled if the product is connected
to a device that does not support BD Wise.
Resolution
Sets the output resolution of the HDMI video signal.
The i and p indicate interlace and progressive scan,
respectively.
• 576p(480p), 720p, 1080i, 1080p, BD Wise
| NOTE |
The BD Wise menu item appears only if BD Wise is
set to On.
Depending on your TV, certain HDMI output
resolutions may not work. Please refer to the user’s
manual of your TV.
If Composite is connected, the resolution supports
only 576i(480i).
1080P may not appear depending on TV.
HDMI Format
Lets you set the colour space format for the HDMI output
to match the capabilities of the connected device (TV,
monitor).
Video Out Signal
Different countries apply different TV standard.
You can select from NTSC or PAL.
Audio
Simple Setup
It is the Function for selecting the Speaker Layout
suitable with the layout type of the connected Speaker.
That is two path to select:
1. Settings
Audio
Simple Setup
2. Settings
System
Initial Setting
Simple
Speaker Setup
• Normal Mode: Use this option when the surround
speakers are located behind you.
• Simple Mode: Use this option if the surround speakers
are located in front of you.
If Simple Mode is selected, Speaker Setting cann't be
set.
Speaker Setting
Speaker Size
You can set the Speaker Size of the Center and Surround
Speakers, as well as Test Tone in this mode.
Sound Edit
You can adjust the balance and level for each speaker.
Press the ▲▼ buttons to select and adjust the desired
speaker.
Press the ◄► buttons to adjust the settings.
Delay Time
If the speakers cannot be placed at equal distances from
the listening position, you can adjust the delay time of the
audio signals from the Center and Surround speakers.
You can also set the Test Tone in this mode.
| NOTE |
The Delay Time menu will be activated only when a
5.1 channel source is played.
You can not set Center and Surround in this mode
when their Speaker Size is set to NONE.
With AC-3, the delay time of surround can be set
between 00 and 15mSEC.Center only can be set
between 00 and 5mSEC.
The Center channel is only adjustable on 5.1 channel
discs.
Test Tone
Use the Test Tone feature to check the speaker
connections.
• Press the ◄► buttons to select On.
• The test tone will be sent to Front Left
Center
Front Right
Surround Right
Surround Left
Subwoofer in order.
To stop the test tone, press the
E
button.
DRC (Dynamic Range Compression)
This feature balances the range between the loudest and
quietest sounds. You can use this function to enjoy Dolby
Digital sound when watching movies at low volume at
night.
AUDIO SYNC
Video and audio sync may not match with digital TV. If
this occurs, adjust the audio delay time to match the
video.
Speaker Selection
• Video is transmitted over the HDMI connection cable
only, and audio is output through the product speakers
only.
Select the Home Theater.
• Both video and audio signals are transmitted over the
HDMI connection cable, and audio is output through
your TV speakers only.
Select the TV Speaker.
HT-F450-XU-11-26.indd 15HT-F450-XU-11-26.indd 15 2013-3-12 8:52:242013-3-12 8:52:24
|
16 English
Settings
| NOTE |
The default setting of this function is Home Theater .
HDMI Audio is automatically down-mixed to 2ch for
TV speakers.
User EQ
You can configure the equalizer settings manually to your
preference.
Audio Return Ch.
You can enjoy TV sound from the Home Cinema
speakers by using just one HDMI cable.
| NOTE |
When Anynet+ (HDMI-CEC) is Off, the Audio Return
Channel function is not available.
Using an ARC (Audio Return Channel)-uncertified
HDMI cable may cause a problem in compatibility.
ARC function is only available if an ARC-compliant TV
is connected.
ARC function is included in D.IN function on the main
set.
If no ARC signal for more than 25 minutes, the
product will automatically turn off.
System
Initial Settings
By using the Initial Settings, you can set the language ,TV
aspect and Simple Setup. (see page 14)
DivX(R) Registration
View DivX(R) VOD Registration Code to purchase and
play DivX(R) VOD content.
| NOTE |
This option is not activated if you select OK. To
activate this option, please activate the DivX(R)
Deactivation.
Even after you reset the system, the settings of DivX
Registration will not be reset.
DivX(R) Deactivation
Select this to get a new registration code.
Language
You can select the language you prefer for on-screen
menu, disc menu, etc.
To select a language that does not appear in the
menu, select OTHERS in the Disc Menu, Audio and
Subtitle, and enter the language code of your country.
For more information, refer to www.samsung.com or
call to Samsung customer service center.
| NOTE |
You cannot select OTHERS in the OSD Language
menu.
The selected language will only appear if it is
supported on the disc.
Security
Security
The Parental Lock function works in conjunction with
DVDs that have been assigned a rating, which helps you
control the types of DVDs that your family watches. There
are up to 8 rating levels on a disc.
Parental Rating
Select the rating level you want to set. Enter the
password and then press the
E
button.
• The password is set to "0000" by default.
Change Password
Select Change and enter the 4-digit password to set the
parental lock using the number buttons on the remote
control.
If you forgot your password
1 .
Remove the disc.
2 .
Press and hold the STOP (
) button on the remote
control for 5 seconds or more. All settings will revert
to the factory settings.
Support
Product Information
Provide the product information such as Model code,
Softrware Version, etc.
HT-F450-XU-11-26.indd 16HT-F450-XU-11-26.indd 16 2013-3-12 8:52:262013-3-12 8:52:26
English 17
|
05 Basic Functions
Disc Playback
Place a disc gently into the tray with the disc's
label facing up
.
| NOTE |
When you stop disc play, the product remembers
where you stopped, so when you press
6
button
again, it will pick up where you left off. (Resume
function works only with DVDs.)
Press the
5
button twice during playback to disable
the Resume function.
Pirated discs will not play in this product because
they violate the CSS (a copy protection system)
recommendations.
will appear when an invalid button is pressed.
If no button input is made for more than 5 minutes in
Stop or Play (music) mode, the screen saver will get
activated.
If the product is left in the screen saver mode for more
than 20 minutes, the power will automatically turn off.
(Except during play a music)
Audio CD(CD-DA)/MP3/WMA
Playback
1 .
Insert an Audio CD(CD-DA) or an MP3 Disc.
• For an Audio CD, the first track will be played
automatically.
- Press the
#$
buttons to move to the
previous/next track.
• For the MP3/WMA disc, press the
◄►
buttons to
select Music, then press the
E
button.
- Press the
▲▼◄►
buttons to select a desired
file and press the
E
button.
- Press the
buttons to move to the
previous/next pages.
2 .
Press the
5
button to stop playback.
| NOTE |
Some MP3/WMA-CDs may not play, depending on
the recording mode.
Table of contents of a MP3-CD varies depending on
the MP3/WMA track format recorded on the disc.
WMA-DRM files cannot be played.
The product will automatically turn off from no Disc
and Stop mode for more than 25 minutes.
JPEG File Playback
Insert a JPEG disc
◄►
(select Photo)
▲▼
(select
the desired folder)
E
▲▼
(select the desired
photo)
E
• The selected file will play and slide show will start.
To stop slide show, press the
7
button.
• You can view the previous/next file by pressing the
◄
,
►
buttons during the slideshow mode.
Rotate Function
Press the GREEN(B) or YELLOW(C) button during the
PAUSE mode.
Using the Playback Function
Forward/Reverse Search
Press the
buttons for Search Function.
| NOTE |
No sound is played in search mode.
The playback search produces sound only when
searching at
1 and
2 speed.
This function is available only for the CD-DA.
Skipping Scenes/Songs
Press the
#$
buttons.
• Each time the button is pressed during playback, the
previous or next chapter, track or directory (file) will be
played.
• You cannot skip chapters consecutively.
Slow Motion Play
Press the
7
button and then
button
for Slow
Motion play.
| NOTE |
No sound is heard during slow playback.
Reverse slow playback does not work.
This function is available for the DivX/DVD.
Step Motion Play
Press the
7
button repeatedly.
• The picture moves forward one frame each time the
button is pressed during playback.
| NOTE |
No sound is heard during step motion playback.
This function is available for the DivX/DVD.
Basic Functions
HT-F450-XU-11-26.indd 17HT-F450-XU-11-26.indd 17 2013-3-12 8:52:282013-3-12 8:52:28
|
18 English
Basic Functions
5 Minute Skip Function
During playback, press the
◄
,
►
button.
• Playback skips 5 minutes forward whenever you press
the
►
button.
• Playback skips 5 minutes backward whenever you
press the
◄
button.
| NOTE |
This function is available only for the DivX that contains
time information.
Using the Disc/Title Menu
During playback,
DISC MENU or TITLE MENU
▲▼◄►
E
• Disc Menu : You can view the menus for the audio
language, subtitle language, profile, etc.
• Title Menu : For DVDs containing multiple titles, you
can view the title of each movie.
| NOTE |
Depending on the disc, menu setup items may vary
and this menu may not be available.
Repeat Playback
DVD/DivX Repeat
You can repeat the title, chapter or the section(A-B
Repeat) of the DVD/DivX.
1 .
During DVD/DivX playback, press the REPEAT
button on the remote control.
2 .
Press the
▲▼
buttons to select a desired repeat
mode, then press the
E
button.
3 .
Press the ▲▼ buttons to select OFF to return to
normal play, then press the
E
button.
CD/MP3 Repeat
During the CD/ MP3 playback, press the REPEAT button
repeatedly to select the repeat mode you want.
• CD :
(Off)
(Track)
(All)
(Random)
(Section A-B)
• MP3 :
(Off)
(Track)
(Directory)
(All)
(Random)
A-B Repeat Playback
You can repeatedly play back a designated section of a
DVD or CD.
1 .
During the DVD disc or CD playback, press the
REPEAT button on the remote control.
2 .
For DVD, press the
▲▼
buttons to select A-. For
CD press the REPEAT button repeatedly until
appears.
3 .
Press the
E
button at the point where you want
repeat play to start (A).
4 .
Press the
E
button at the point where you want
repeat play to stop (B).
5 .
To return to normal playback,
For DVD, press the REPEAT button ,then press the
▲▼
buttons to select to OFF. For CD, press the
REPEAT button to select to
.
| NOTE |
The A-B Repeat function does not operate with DivX,
MP3 or JPEG discs.
Displaying Disc Information
1 .
During playback, press the TOOLS button on the
remote control.
2 .
Press the
▲▼
buttons to select the desired item.
3 .
Press the
◄►
buttons to make the desired setup
change and then press the
E
button.
• You may use the number buttons of the remote
control to control some items.
4 .
To make Disc information disappear, press the
TOOLS button again.
| NOTE |
Some tools menus may differ depending on discs and
files.
TOOLS menu
• Title( ) : To access the desired title when there is
more than one in the disc.
• Chapter(
) : Most DVD discs are recorded in
chapters so that you can quickly find a specific chapter.
• Playing time(
) : Allows playback of the film from
a desired time. You must enter the starting time as a
reference. The time search function does not operate
on some discs.
• Audio(
): Refers to the film's soundtrack
language. A DVD Disc can contain up to 8 audio
languages.
HT-F450-XU-11-26.indd 18HT-F450-XU-11-26.indd 18 2013-3-12 8:52:312013-3-12 8:52:31
English 19
|
05 Basic Functions
• Subtitle( ): Refers to the subtitle languages
available in the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them off from
the screen. A DVD Disc can contain up to 32 subtitle
languages.
• Angle(
): When a DVD contains multiple angles of a
particular scene, you can use the Angle function.
TOOLS
▲▼
(select AUDIO, SUBTITLE or ANGLE)
◄►
(select the desired option)
| NOTE |
Depending on the disc, the Subtitle and Audio
Language functions may not be available.
The Angle function works only with discs on which
multiple angles have been recorded.
Caption Function
• You must have some experience with video extraction
and editing in order to use this feature properly.
• To use the caption function, save the caption file (*.smi)
in the same file name as that of the DivX media file (*.avi)
within the same folder.
• Up to 100 alphanumeric characters or 50 East Asian
characters (2 byte characters such as Korean and
Chinese) for the file name.
• The subtitle of DivX files are *.smi, *.sub, *.srt over 148
kbyte is not supported.
Using the Special Remote Control
Buttons
P.BASS
P.BASS
The P.BASS function provides a bass boost to
reinforce the low frequencies.
| NOTE |
The P.BASS function is only available with 2
channel LPCM sources such as MP3, DivX, CD
and WMA.
GIGA
GIGA
The GIGA Sound Function amplifies bass and
improves bass twice as much for you to appreciate
powerful real sound. (Subwoofer only)
| NOTE |
The GIGA Sound works when in 2-channel LPCM
mode only.
S.VOL (smart volume)
S.VOL
This will regulate and stabilize the volume level against
a drastic volume change when changing channels or
during a scene transition.
SMART VOLUME ON
SMART VOLUME OFF
S/W LEVEL
S/W LEVEL
You can also press the S/W LEVEL button on the
remote control and use the
◄
or
►
buttons to adjust
the level of subwoofer.
DSP (Digital Signal Processor)/EQ
DSP/EQ
DSP (Digital Signal Processor)
DSP modes have been designed to simulate different
acoustic environments.
EQ
You can select POPS, JAZZ , ROCK, or USER to
optimize the sound for the genre of music you are
playing.
| NOTE |
The DSP/EQ function is only available in Stereo
mode.
The DSP/EQ function is not available while playing
AC3 signal in 2.1 channel mode.
FOOTBALL
FOOTBALL
Enjoy the music like on the soccer field with FOOTBALL
button.
Each time you press the FOOTBALL button on the
remote control.
FOOTBALL MODE ON
FOOTBALL MODE OFF
FOOTBALL MODE ON: You will feel to enjoy music on
the soccer field.
HT-F450-XU-11-26.indd 19HT-F450-XU-11-26.indd 19 2013-3-12 8:52:352013-3-12 8:52:35
|
20 English
Basic Functions
V SURROUND
V SURROUND
It is only operational when 2 Channel Audio is playing.
It will change 2 channel Audio Source to 5.1 channel
Sound and there is output.
Each time you press the V-SURROUND button on the
remote control.
Virtual Surround on
Virtual Surround off
• Virtual Surround on: change 2 channel audio to
5.1 channel and there is Sound output by 5.1
channel.
• Virtual Surround off: Output of 2 channel Audio is
Sound output by 2 channel. (Original Sound).
TV SOUND
TV SOUND
You can listen via Home Theater Speaker or TV Speaker
with TV SOUND button.
1 .
Connect the HDMI cable to TV and Home theater.
2 .
Press the TV SOUND button on the remote control.
3 .
Each time you press the TV SOUND button, TV
SOUND ON/OFF flashes shortly on the Display
part on the Front panel, then change to D.IN.
-TV SOUND ON : Output to Home Theater Speaker.
-TV SOUND OFF : Output to Anynet+ connected TV
Speaker.
Use in this case:
1) If you want to listen to the sound via home theater
speaker when you watch a TV.
2) If you want to listen to the sound from the USB media
that plugged to the TV via home theater speaker.
TV SOUND ON/OFF support specification
Connected
TV
TV Anynet+
(HDMI-CEC)
Setting
TV
Sound
ON
TV
Sound
OFF
Anynet+
(HDMI-CEC)
supported
TV
ON O O
OFF O O
Anynet+
(HDMI-CEC)
supported
TV
No opeartion O O
Make sure that D.IN function is changed to TV CEC
ON state,otherwise ARC audio is not available .
Listening to Radio
Using buttons on the Remote Control
1 .
Press the FUNCTION button to select FM.
2 .
Tune in to the desired station.
• Preset Tuning 1 : You must first add a desired
frequency as a preset. Press the
5
button to
select PRESET and then press the TUNING/CH
(
,.
) button to select the preset station.
• Manual Tuning : Press the
5
button to select
MANUAL and then press the TUNING/CH (
,.
)
button to tune in to a lower or higher frequency.
• Automatic Tuning : Press the
5
button to select
MANUAL and then press and hold the TUNING/
CH (
,.
) button to automatically search the
band.
Setting Mono/Stereo
Press the MO/ST button.
• Each time the button is pressed, the sound switches
between STEREO and MONO.
• In a poor reception area, select MONO for a clear,
interference-free broadcast.
Presetting Stations
Example : Presetting FM 89.10 in the memory
1 .
Press the FUNCTION button to select FM.
2 .
Press the TUNING/CH (
,.
) button to select
<89.10>.
3 .
Press the TUNER MEMORY button.
• Number flashes on the display.
4 .
Press the TUNING/CH (
,.
) buttons to select
preset number.
• You can select between 1 and 15 presets.
5 .
Press the TUNER MEMORY button again.
• Press the TUNER MEMORY button before
number disappears from the display.
• Number disappears from the display and the
station is stored in memory.
6 .
To preset another station, repeat steps 2 to 5.
HT-F450-XU-11-26.indd 20HT-F450-XU-11-26.indd 20 2013-3-12 8:52:372013-3-12 8:52:37
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
Diğer dillerde
- English: Samsung HT-F455 User manual
İlgili Makaleler
-
Samsung HT-D350 Kullanım kılavuzu
-
-
-
-
-
-
Samsung HT-F4550 El kitabı
-
-
-
