Panasonic KXTGA715FX Kullanma talimatları

Charge the batteries for about 7 hours before initial use.

Please read these operating instructions before using the unit and save them for future

reference.

Contents/İçindekiler Page/Sayfa

English instructions 1 - 24

Türkçe talimatlar (1) - (24)

This unit is an additional handset for use with the following Panasonic

Digital Cordless Phones:

KX-TG7100/KX-TG7120/KX-TG7150/KX-TG7170

KX-TG8100/KX-TG8120

KX-TG9120

You must register this unit to your base unit before it can be used.

Operating Instructions

Model No. KX-TGA715FX

KX-TGA717FX

Additional Digital Cordless Handset

KX-TGA715

TGA715FX_717FX(e-e).book Page 1 Monday, February 5, 2007 1:50 PM

2

Table of Contents

Preparation

Introduction .............................................. 3

Accessory information............................... 4

Important information ............................... 5

Bone conduction earpiece (KX-TGA717

only) ......................................................... 6

Controls .................................................... 7

Displays .................................................... 8

Connections ............................................. 8

Battery installation/replacement ............... 9

Battery charge .......................................... 9

Symbols used in these operating

instructions ............................................. 10

Display language .................................... 10

Registering the handset to your base

unit ......................................................... 11

Accessibility features

Talking number display (Voice

announce) .............................................. 12

Basic Operations

Making/answering calls .......................... 13

Handset phonebook ............................... 13

Caller list ................................................ 14

Multi-unit operation................................. 15

Handset/Base Unit Settings

Handset/base unit settings ..................... 16

Time settings........................................... 18

Answering System Features

Answering system .................................. 19

Useful Information

Using the belt clip ................................... 20

Using the shoulder rest attachment ....... 20

Character entry ....................................... 21

Troubleshooting for accessibility

features .................................................. 22

Specifications ......................................... 23

TGA715FX_717FX(e-e).book Page 2 Monday, February 5, 2007 1:50 PM

3

Preparation

Introduction

Thank you for purchasing a new Panasonic digital cordless phone.

Declaration of Conformity:

L Panasonic Communications Co., Ltd. declares that this equipment is in compliance with the

essential requirements and other relevant provisions of Radio & Telecommunications

Terminal Equipment (R&TTE) Directive 1999/5/EC.

Declarations of Conformity for the relevant Panasonic products described in this manual

are available for download by visiting:

http://www.doc.panasonic.de

Contact:

Panasonic Services Europe

a Division of Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Note:

L In the event of problems, you should contact your equipment supplier in the first instance.

Your phone

KX-TGA715

(Big button type

handset)

KX-TGA717

(Bone conduction

type handset)

TGA715FX_717FX(e-e).book Page 3 Monday, February 5, 2007 1:50 PM

4

Preparation

Accessory information

Included accessories

*1 The handset cover comes attached to the handset.

Additional/replacement accessories

Please contact your nearest Panasonic dealer for sales information.

Note:

L When replacing the batteries, use only 2 rechargeable AAA (R03) size nickel metal hydride

(Ni-MH) batteries of capacity up to 750 mAh. We recommend using Panasonic

rechargeable batteries (Model No. P03P).

L We cannot be responsible for any damage to the unit or degradation of performance which

may occur from using non-Panasonic rechargeable batteries.

No. Accessory items Quantity

1 AC adaptor (Part No. PQLV209CE) 1

2 Charger (Part No. PQLV30045) 1

3 Rechargeable batteries AAA (R03) size

(Part No. HHR-55AAAB or HHR-4EPT)

2

4 Handset cover

*1

1

5 Belt clip 1

6 Shoulder rest 1

123456

No. Model No. Description

1 KX-TCA94EX Headset

1

TGA715FX_717FX(e-e).book Page 4 Monday, February 5, 2007 1:50 PM

5

Preparation

Important information

General

L Use only the AC adaptor included with this

product, noted on page 4.

L Do not connect the AC adaptor to any AC

outlet other than a standard 220–240 V

AC outlet.

L This product is unable to make calls when:

– the portable handset battery(ies) need

recharging or have failed.

– there is a power failure.

L Do not open the charger or handset other

than to replace the battery(ies).

L This product should not be used near

emergency/intensive care medical

equipment and should not be used by

people with pacemakers.

L Care should be taken that objects do not

fall onto, and liquids are not spilled into,

the unit. Do not subject this product to

excessive smoke, dust, mechanical

vibration or shock.

Environment

L Do not use this product near water.

L This product should be kept away from

heat sources such as radiators, cookers,

etc. It should also not be placed in rooms

where the temperature is less than 5 °C or

greater than 40 °C.

L The AC adaptor is used as the main

disconnect device. Ensure that the AC

outlet is installed near the product and is

easily accessible.

Warning:

L To prevent the risk of electrical shock, do

not expose this product to rain or any

other type of moisture.

L Unplug this product from power outlets if it

emits smoke, an abnormal smell, or

makes unusual noise. These conditions

can cause fire or electric shock. Confirm

that smoke has stopped emitting and

contact an authorised service centre.

L Do not spill liquids (detergents, cleansers,

etc.) onto the telephone line cord plug, or

allow it to become wet at all. This may

cause a fire. If the telephone line cord plug

becomes wet, immediately pull it from the

telephone wall jack, and do not use.

Battery caution

L We recommend using the battery(ies)

noted on page 4. Use only rechargeable

battery(ies).

L Do not mix old and new batteries.

L Do not dispose of the battery(ies) in a fire,

as they may explode. Check with local

waste management codes for special

disposal instructions.

L Do not open or mutilate the battery(ies).

Released electrolyte from the battery(ies)

is corrosive and may cause burns or injury

to the eyes or skin. The electrolyte may be

toxic if swallowed.

L Exercise care when handling the

battery(ies). Do not allow conductive

materials such as rings, bracelets or keys

to touch the battery(ies), otherwise a short

circuit may cause the battery(ies) and/or

the conductive material to overheat and

cause burns.

L Charge the battery(ies) in accordance

with the information provided in these

operating instructions.

L Only use the included base unit (or

charger) to charge the battery(ies). Do not

tamper with the base unit (or charger).

Failure to follow these instructions may

cause the battery(ies) to swell or explode.

TGA715FX_717FX(e-e).book Page 5 Monday, February 5, 2007 1:50 PM

6

Preparation

Information on Disposal for Users of

Waste Electrical & Electronic Equipment

(private households)

This symbol on the products and/or

accompanying documents means that used

electrical and electronic products should not

be mixed with general household waste. For

proper treatment, recovery and recycling,

please take these products to designated

collection points, where they will be

accepted on a free of charge basis.

Alternatively, in some countries you may be

able to return your products to your local

retailer upon the purchase of an equivalent

new product.

Disposing of this product correctly will help

to save valuable resources and prevent any

potential negative effects on human health

and the environment which could otherwise

arise from inappropriate waste handling.

Please contact your local authority for

further details of your nearest designated

collection point.

Penalties may be applicable for incorrect

disposal of this waste, in accordance with

national legislation.

For business users in the European

Union

If you wish to discard electrical and

electronic equipment, please contact your

dealer or supplier for further information.

Information on Disposal in other

Countries outside the European Union

This symbol is only valid in the European

Union.

If you wish to discard this product, please

contact your local authorities or dealer and

ask for the correct method of disposal.

Bone conduction earpiece

(KX-TGA717 only)

The handset features a bone conduction

earpiece that uses vibrations to create

sound during your telephone conversations.

For proper operation press the bone

conduction earpiece against your face near

the ear.

Normally, sound enters the ear canal and

vibrates the eardrum. People feel the

vibration within the inner ear and

comprehend it as it is received by the

auditory nerve.

Place the bone conduction earpiece against

your face (not your ear). Try different

locations to find which location works best.

Start with the temple area.

Note:

L Do not place the bone conduction

earpiece on a hearing aid. Howling or

other interference may be heard.

L The effectiveness of the bone conduction

External ear

Middle ear

Inner ear

Auditory

nerve

Sound

Bone

conduction

earpiece

TGA715FX_717FX(e-e).book Page 6 Monday, February 5, 2007 1:50 PM

7

Preparation

earpiece will vary by the type and degree

of hearing loss of the user.

L As sound is generated by vibration, users

with normal hearing can use the handset

by placing the bone conduction earpiece

against the ear, as an ordinary telephone.

L If the bone conduction earpiece gets dusty

or greasy, clean it with a soft, dry cloth.

Controls

Handset (KX-TGA715)

Handset (KX-TGA717)

A Speaker

B Charge contact

C Headset jack

D {j/OK} (Menu/OK)

E {k} (Phonebook)

F {C} (Talk)

G Navigator key ({^}/{V}/{>}/{<})

H {s} (Speakerphone)

I {R} (Recall)

J Charge indicator

Ringer indicator

Message indicator

*1

K KX-TGA715

Receiver

KX-TGA717

Bone conduction earpiece

L Display

M {R} (Redial/Pause)

N {ih} (Off/Power)

O

{

C/T} (Clear/Mute)

P Dial keypad

Q {INT} (Intercom)

R Microphone

*1 For KX-TG7120/KX-TG8120/KX-

TG9120 users only

N

B

A

O

P

Q

R

L

K

M

F

G

I

H

J

D

C

E

B

A

N

O

Q

R

L

K

M

F

G

I

H

J

D

C

E

P

TGA715FX_717FX(e-e).book Page 7 Monday, February 5, 2007 1:50 PM

8

Preparation

Displays

Display icons

*1 For KX-TG7120/KX-TG8120/KX-

TG9120 users only

*2 Voice mail users only

Connections

Connect the AC adaptor to the charger and

route the cable as shown. The charger can

be mounted on the wall, if required.

Note:

L The AC adaptor must remain connected

at all times. (It is normal for the adaptor to

feel warm during use.)

L The AC adaptor should be connected to a

vertically oriented or floor-mounted AC

outlet. Do not connect the AC adaptor to a

ceiling-mounted AC outlet, as the weight

of the adaptor may cause it to become

disconnected.

Location

L For maximum distance and noise-free

operation, place your base unit:

– away from electrical appliances such as

TVs, radios, personal computers or

other phones.

– in a convenient, high and central

location.

Display

icon

Meaning

w Within range of a base unit

L When flashing: Handset

is searching for base unit.

(out of range of base unit,

handset is not registered

to base unit, no power on

base unit)

L Handset is accessing base

unit. (intercom, paging,

changing base unit

settings, etc.)

k Handset is on an outside

call.

u Answering system is on.

*1

(page 19)

5 Battery strength

[2] Handset number (Standby

display setting, page 16)

0 New voice mail message

received

*2

L Line is being used by

another handset.

L Answering system is

being used by another

handset or the base

unit.

*1

(220–240 V,

50 Hz)

Screws

25 mm

Hooks

Use only the included AC adaptor.

TGA715FX_717FX(e-e).book Page 8 Monday, February 5, 2007 1:50 PM

9

Preparation

Battery installation/

replacement

Important:

L Use only the included rechargeable

batteries noted on page 4, 5.

L When replacing batteries, we recommend

using the Panasonic rechargeable

batteries noted on page 4, 5.

L Wipe the battery ends (S, T) with a dry

cloth.

L When installing the batteries, avoid

touching the battery ends (S , T) or the

unit contacts.

1 Press the notch on the handset cover

firmly and slide it in the direction of the

arrow.

L When replacing batteries, remove the

old batteries positive (S) end first.

2 Insert the batteries negative (T) end first.

Close the handset cover.

Battery charge

Place the handset on the charger for

about 7 hours before initial use.

When charging, the battery icon is shown as

follows.

When the batteries are fully charged, 5

remains on the display.

L The charge indicator lights up when the

handset is placed on the charger.

L The pictured model is KX-TGA715.

Note:

L The handset display may show “Please

Wait...” when the handset is placed on

the charger if it is not registered to a base

unit.

L It is normal for the handset to feel warm

during charging.

L If you want to use the unit immediately,

charge the batteries for at least 15

minutes.

L Clean the charge contacts of the handset,

charger with a soft, dry cloth once a

month, otherwise the batteries may not

charge properly. Clean more often if the

unit is exposed to grease, dust, or high

humidity.

Charge contacts

TGA715FX_717FX(e-e).book Page 9 Monday, February 5, 2007 1:50 PM

10

Preparation

Battery strength

Panasonic Ni-MH battery performance

(included batteries)

Note:

L It is normal for batteries not to reach full

capacity at the initial charge. Maximum

battery performance is reached after a few

complete cycles of charge/discharge

(use).

L Actual battery performance depends on a

combination of how often the handset is in

use and how often it is not in use

(standby).

L Battery operating time may be shortened

over time depending on usage conditions

and ambient temperature.

L Even after the handset is fully charged,

the handset can be left on the charger

without any ill effect on the batteries.

L The battery strength may not be displayed

correctly after you replace the batteries. In

this case, place the handset on the

charger and charge for at least 7 hours.

Symbols used in these

operating instructions

Display language

17 display languages are available.

1 {ih} i {j/OK}

2 Press {^} or {V} to select “Handset

Setup”. i {>}

3 Press {^} or {V} to select “Display

Setup”. i {>}

4 Press {^} or {V} to select “Select

Language”. i {>}

5 Press {^} or {V} to select the desired

language. i {>} i {ih}

Note:

L If you select a language you cannot read,

press {ih}, press {j/OK}, press {^} 3

times, press {>}, press {V} 2 times, press

{>}, press {V}, press {>}, select the

desired language, press {>}, then press

{ih}.

L To change the voice announce language,

Battery icon Battery strength

5 High

6 Medium

7 Low

When flashing: Needs

to be charged.

Operation Operating time

In continuous use KX-TGA715:

12 hours max.

KX-TGA717:

10 hours max.

In continuous

standby mode

150 hours max.

Symbol Meaning

{j/OK} Press {j/OK}.

i Proceed to the next

operation.

“ ” Select the words in

quotations shown on the

display (e.g., “Handset

Setup”) by pressing {^}

or {V}.

TGA715FX_717FX(e-e).book Page 10 Monday, February 5, 2007 1:50 PM

11

Preparation

see page 12.

Registering the handset to

your base unit

Register to:

KX-TG7100/KX-TG7120/KX-TG7150/KX-

TG7170/KX-TG8100/KX-TG8120/KX-

TG9120

Ensure that the handset is switched on. If it

is not on, press and hold {ih} for few

seconds to turn the handset on.

1 Lift the handset and press {ih} to put

the handset in standby mode.

2 Press and hold {x} on the base unit for

about 3 seconds, until the registration

tone sounds.

3 Place the handset on the base unit. The

registration tone continues to sound. With

the handset still on the base unit, wait

until a confirmation tone sounds and w

stops flashing.

Note:

L If an error tone sounds, or if w is still

flashing, register the handset manually

(page 15).

L If all registered handsets start ringing in

step 2, press {x} to stop. Start again from

step 1.

L Charge the batteries for about 7 hours

before initial use.

L The answering system is available only

when KX-TGA715/KX-TGA717 is

registered to KX-TG7120/KX-TG8120/

KX-TG9120.

L KX-TGA715/KX-TGA717 does not

support the SMS features.

L For KX-TG9120 with KX-TGA914

(Cordless camera) users

KX-TGA715/KX-TGA717 does not

support camera monitoring features.

L For KX-TG9120 with KX-TGA915 (USB

adaptor) users

KX-TGA715/KX-TGA717 does not

support internet call features.

TGA715FX_717FX(e-e).book Page 11 Monday, February 5, 2007 1:50 PM

12

Accessibility features

Talking number display

(Voice announce)

The voice announce features allow the

handset to announce displayed phone

number. (Caller ID announce/List

announce)

Caller ID announce

When you receive an outside call which has

phone number information, the handset

announces the displayed phone number

from the handset speaker.

L To announce outside caller’s phone

number, you must first subscribe to Caller

ID service. Consult your service provider/

telephone company for details.

L When receive a call while on the phone,

the 2nd caller’s phone number will not be

announced even if you subscribe to both

Caller ID and Call Waiting Caller ID

services.

L The announcement is heard at the ringer

volume (page 16).

L This feature can be turned on or off (page

12).

List announce

The handset announces phone numbers

from the handset speaker while you are

viewing the redial list, caller list, and

phonebook.

L If the displayed phone number has a P

(pause), the handset inserts a 0.5 second

pause for each P and if the number has

the other symbols (for example, ;, #,

etc.), the handset skips the symbols and

announces the next number.

Setting volume for voice

announce

You can set the volume for list announce.

The volume for caller ID announce is set

when setting the ringer volume on (page

16).

1 {j/OK}

2 “Handset Setup” i {>}

3 “Other Options” i {>}

4 “Voice Announce” i {>}

5 “Volume” i {>}

6 Select the desired volume.

L To turn the voice announce feature off,

select the volume “Off”.

7 {>} i {ih}

Note:

L The caller ID announce is heard at the

handset ringer volume (page 16). When

the volume for voice announce is set to

“Off”, the handset does not announce the

phone number regardless of the ringer

volume.

Selecting language for voice

announce

6 voice announce languages are available.

1 {j/OK}

2 “Handset Setup” i {>}

3 “Other Options” i {>}

4 “Voice Announce” i {>}

5 “Select Language” i {>}

6 Select the desired language. i {>} i

{ih}

Note:

L To change the display language, see

page 10

TGA715FX_717FX(e-e).book Page 12 Monday, February 5, 2007 1:50 PM

13

Basic Operations

Making/answering calls

Handset phonebook

Feature Operation

Power on Press {ih} for about 1 second.

Power off Press {ih} for about 2 seconds.

Making calls Dial the phone number. i {C}/{s}

Answering calls {C}

Hanging up {ih}

Receiver/speaker volume Press {^} or {V} while on a call.

Making a call with redial

list

{R} i Press {^} or {V} to select the desired number.

i {C}/{s}

Erasing number in the

redial list

{R} i Press {^} or {V} to select the desired number.

i {>} i “Erase” i {>} i “Yes” i {>} i

{ih}

Muting your voice While on a call, press

{

C/T}. To return to the conversation,

press

{

C/T} again.

{

R

}

button (to use the

recall feature)

{

R

}

is used to access optional telephone services. Contact

your service provider/telephone company for details.

Feature Operation

Adding entries (up to 50

names and phone

numbers)

{k} i {j/OK} i “New Entry” i {>} i Enter the

party’s name (16 characters max.). i

{j/OK} i Enter the party’s phone number (24 digits

max.). i {j/OK} i “Save” i { >} i {ih}

L To enter a name, see page 21.

Making calls {k} i Press {^} or {V} to display the desired entry. i

{C}/{s}

Searching by first

character (index search)

{k} i Press the dial key ({0} to {9}) which contains the

character you are searching for (page 21). i Press {^} or

{V} to display the desired entry.

L To change the character entry mode while searching:

{R} i Select the character entry mode. i {>}

Editing entries {k} i Press {^} or {V} to display the desired entry. i

{j/OK} i “Edit” i {> } i Edit the name. i

{j/OK} i Edit the phone number. i {j/OK} i

“Save” i {>} i {ih}

TGA715FX_717FX(e-e).book Page 13 Monday, February 5, 2007 1:50 PM

14

Basic Operations

Caller list

Phone numbers of the last 50 callers will be logged in the caller list.

Erasing an entry {k} i Press {^} or {V} to display the desired entry. i

{j/OK} i “Erase” i {>} i “Yes” i {>} i

{ih}

Erasing all entries {k} i {j/OK} i “Erase All” i {>} i “Yes”

i {>} i “Yes” i {>} i {ih}

Copying one entry {k} i Press {^} or {V} to display the desired entry. i

{j/OK} i “Copy” i {> } i Enter the handset

number you wish to send the handset phonebook entry to.

i Press {ih} when “Completed” is displayed.

Copying all entries {k} i {j/OK} i “Copy All” i {>} i Enter the

handset number you wish to send the handset phonebook

entry to. i Press {ih} when “Completed” is displayed.

Chain dial While on a call, press {k}. i Press {^} or {V} to select

the desired entry. i Press {>} to dial the number.

Feature Operation

Viewing the caller list and

calling back

{j/OK} i “Caller List” i {>} i Press {V} to

search from the most recent call, or press {^} to search from

the oldest call. i {C}/{s}

Editing a caller’s phone

number before calling

back

{j/OK} i “Caller List” i {>} i Press {^} or {V}

to display the desired entry. i {j/OK} i “Edit and

Call” i {>} i Edit the number. i {C}/{s}

Storing caller information

into the handset

phonebook

{j/OK} i “Caller List” i {>} i Press {^} or {V}

to display the desired entry. i {j/OK} i “Add

phonebook” i {>} i Continue from “Enter the party’s

name” on page 13 (Adding entries).

Erasing an entry {j/OK} i “Caller List” i {>} i Press {^} or {V}

to display the desired entry. i {j/OK} i “Erase” i

{>} i “Yes” i {>} i {ih}

Erasing all entries {j/OK} i “Caller List” i {>} i {j/OK} i

“Erase All” i {>} i “Yes” i {>} i {ih}

Feature Operation

TGA715FX_717FX(e-e).book Page 14 Monday, February 5, 2007 1:50 PM

15

Basic Operations

Multi-unit operation

*1 KX-TG7150/KX-TG7170 does not support conference call feature.

*2 After pressing {x}, the rest of this procedure must be completed within 1 minute.

*3 If you forget the base unit PIN, consult your nearest Panasonic service centre.

Feature Operation

Intercom: calling Example: When you call handset 1

{INT} i Press {1} (desired handset number).

L When finished talking, press {ih}.

Intercom: answering Press {C}/{s}.

L When finished talking, press {ih}.

Transferring calls between

handsets

Example: When you transfer a call to handset 1

During an outside call, press {INT}. i Press {1} (desired

handset number). i When the handset 1 answered, press

{ih} to complete transfer.

Conference calls

*1

(2 people can have a

conference call with an

outside party)

Example: When you make a conference call with handset 1

During an outside call, press {INT}. i Press {1} (desired

handset number). i When the handset 1 answered, press

{3} to establish a conference call.

Manual registration Handset:

{j/OK} i “Handset Setup” i {>} i

“Registration” i {>} i “Register H.set” i

{>}

Base unit:

Press and hold {x} on the base unit for about 3 seconds,

until the registration tone sounds.

*2

Handset:

Wait until “Enter Base PIN” is displayed, then enter the

base unit PIN (default: “0000”).

*3

i {j/OK}

L When the handset has been registered successfully, w

will stop flashing.

Cancelling a handset {j/OK} i “Base Unit Setup” i {>} i Enter

“335”. i “Cancel Handset” i { >} i Select the

handset(s) you want to cancel, by pressing the desired

handset number. i {j/OK} i “Yes” i {>} i

{ih}

TGA715FX_717FX(e-e).book Page 15 Monday, February 5, 2007 1:50 PM

16

Handset/Base Unit Settings

Handset/base unit settings

Handset settings

When customising the handset, the current item or setting is indicated by >.

1 {j/OK}

2 Press {^} or {V} to select “Handset Setup”. i {>}

3 Press {^} or {V} to select the desired item in the handset settings menu. i {>}

4 Press {^} or {V} to select the desired item in the sub-menu. i {>}

L In some cases, you may need to select from a second sub-menu. i {>}

5 Press {^} or {V} to select the desired setting then press {>} or follow the instruction in the

rightmost column of the chart.

L To exit the operation, press {ih}.

Handset settings

menu

Sub-menu Sub-menu 2 Feature (default setting)

Time Settings Set Date &

Time

— Set the date and time

Alarm — Set the alarm: page 18

Ringer Setup Ringer Volume — Handset ringer volume

(Maximum)

*1

Ext. Ringtone — Ringtones for outside calls

(“Ringtone 1”)

*2*3

Int. Ringtone — Ringtones for intercom

calls

(“Ringtone 3”)

*3

Display Setup Standby

Display

— Standby mode display

(“Off”)

*4

Select

Language

— Display language

(“English”): page 10

Contrast — Display contrast (Level 3)

Registration Register H.set — Manual registration:

page 15

Other Options New Msg.

Alert

*5

— New message alert (“Off”)

Keytones — Keytones on/off (“On”)

Auto Talk — Auto talk on/off (“Off”)

*6

Voice Announce Volume Voice announce volume

(“Middle”): page 12

Select

Language

Voice announce language

(“English”): page 12

TGA715FX_717FX(e-e).book Page 16 Monday, February 5, 2007 1:50 PM

17

Handset/Base Unit Settings

*1 When the ringer is turned off, the handset will ring:

– at the minimum level for alarm

– at the minimum level for intercom calls

– at the maximum level for paging

*2 If you select one of the melody ringtones, the ringtone will continue to sound for several

seconds if the caller hangs up before you answer. You may hear a dial tone or no one on

the line when you answer a call.

Inc.

*4 If “Off” is selected, only current date and time are displayed.

If “Handset Number” is selected and the current handset number is 2, “[2]” is displayed.

*5 For KX-TG7120/KX-TG8120/KX-TG9120 users only

This feature alerts you when new messages have been recorded.

The message indicator on the handset flashes until you have listened to all new

messages.

While message alert is on, battery operating time is shortened (page 10).

*6 Auto talk feature allows you to answer calls simply by lifting the handset off the base unit

or charger. You do not need to press {C}.

Base unit settings

You can set your base unit settings using this handset, please refer to your base unit

operating instructions for further details.

TGA715FX_717FX(e-e).book Page 17 Monday, February 5, 2007 1:50 PM

18

Handset/Base Unit Settings

Time settings

Alarm

An alarm will sound for 3 minutes at the set time once or daily. Set the date and time

beforehand (page 16).

1 {j/OK} i “Handset Setup” i {>}

2 “Time Settings” i {>}

3 “Alarm” i Press {>} 2 times.

4 Select an alarm mode. i {>}

5 Enter the desired hour and minute. i {j/OK}

6 Select the desired ringtone. i {>}

7 “Save” i {>} i {ih}

Note:

L To stop the alarm, press any dial key.

L When in talk or intercom mode, the alarm will not sound until the call has ended.

L If you select “Once”, the setting will change to “Off” after the alarm sounds.

Off Turns alarm off. Press {>} again, then press {ih} to finish.

Once The alarm sounds once at the set time. Enter the desired day and month.

Daily An alarm sounds daily at the set time.

TGA715FX_717FX(e-e).book Page 18 Monday, February 5, 2007 1:50 PM

19

Answering System Features

Answering system

Applicable for:

KX-TG7120/KX-TG8120/KX-TG9120

You can operate your base unit answering system using this handset.

1 {j/OK}

2 Press {^} or {V} to select “Answer System”. i {>}

3 Press {^} or {V} to select the desired item in the answering system menu. i {>}

L In some cases, you may need to select from sub-menu. i {>}

L To exit the operation, press {ih}.

*1 Refer to your base unit operating instructions for further details.

Answering

system menu

Sub-menu Feature (default setting)

Play New Msg. — Play new messages

– To repeat the message, press {<} or {1}.

– To skip the message, press {>} or {2}.

– To stop the message, press {9}.

– To erase the message, press {*}{4}.

Play All Msg. — Play all messages

– To repeat the message, press {<} or {1}.

– To skip the message, press {>} or {2}.

– To stop the message, press {9}.

– To erase the message, press {*}{4}.

Record

Greeting

— Record greeting message

– To stop recording, press {j/OK}.

Answer On — Turn answering system on

Answer Off — Turn answering system off

Play Greeting — Play greeting message

– To stop the message, press {9}.

Erase Message Erase All Erase all messages

Erase Greeting Erase greeting message

Settings

*1

——

TGA715FX_717FX(e-e).book Page 19 Monday, February 5, 2007 1:50 PM

20

Useful Information

Using the belt clip

Attaching the belt clip

Removing the belt clip

L The pictured model is KX-TGA715.

Using the shoulder rest

attachment

The shoulder rest attachment allows hands-

free phone conversations.

Attaching the shoulder rest attachment

Attach the included belt clip to the handset

beforehand (page 20). Slide the shoulder

rest attachment to the belt clip until it clicks.

Note:

L If the charger is mounted on a wall,

remove the shoulder rest attachment

before charging the handset.

Removing the shoulder rest attachment

TGA715FX_717FX(e-e).book Page 20 Monday, February 5, 2007 1:50 PM

Sayfa yükleniyor ...

Panasonic KXTGA715FX Kullanma talimatları

Bu kılavuz için de uygundur

Panasonic KXTGA715FX Kullanma talimatları

Diğer dillerde

İlgili Makaleler

Diğer Belgeler