Hach AV9000 Kullanım kılavuzu

DOC026.98.80186

Submerged Area/Velocity

Sensor and AV9000

08/2017, Edition 8

User Manual

Manuel d'utilisation

Manual del usuario

Manuale d'uso

Bedienungsanleitung

Manual do Usuário

Instrukcja obsługi

Kullanım Kılavuzu

English..............................................................................................................................3

Français......................................................................................................................... 22

Español.......................................................................................................................... 42

Italiano............................................................................................................................ 63

Deutsch.......................................................................................................................... 83

Português.................................................................................................................... 103

Polski............................................................................................................................ 123

Türkçe...........................................................................................................................143

2

Table of contents

Specifications on page 3 Operation on page 14

General information on page 4 Maintenance on page 15

Installation on page 7 Replacement parts and accessories on page 19

Specifications

Specifications are subject to change without notice.

Specifications—Submerged area velocity sensor

Performance will vary depending on channel size, channel shape and site conditions.

Velocity measurement

Method Doppler ultrasonic

Transducer type: Twin 1 MHz piezoelectric crystals

Typical minimum depth for

velocity

2 cm (0.8 in.)

Range -1.52 to 6.10 m/s (-5 to 20 ft/s)

Accuracy ± 2% of reading (in water with uniform velocity profile)

Level measurement

Method Pressure transducer with stainless steel diaphragm

Accuracy (static)

• ±0.16% full scale ±1.5% of reading at constant temp (±2.5 ºC)

• ±0.20% full scale ±1.75% of reading from 0 to 30 ºC (32 to 86 ºF)

• ±0.25% full scale ±2.1% of reading from 0 to 70 ºC (32 to 158 ºF)

Velocity-induced depth error Compensated based on flow velocity

Level range

• Standard: 0–3 m (0–10 ft)

• Extended: 0–9 m (0–30 ft)

Allowable level

• Standard: 10.5 m (34.5 ft)

• Extended: 31.5 m (103.5 ft)

General attributes

Air intake Atmospheric pressure reference is desiccant protected

Operating temperature 0 to 70 ºC (32 to 158 ºF)

Level compensated temperature

range

0 to 70 ºC (32 to 158 ºF)

Material Noryl

®

outer shell with epoxy potting within

Power consumption Less than or equal to 1.2 W @ 12 VDC

Cable Urethane sensor cable with air vent

Connector Hard anodized, satisfies Military Spec 5015

Cable lengths available

• Standard: 9, 15, 23 and 30.5 m (30, 50, 75, 100 ft)

• Custom: 30.75 m (101 ft) to 76 m (250 ft) maximum

English 3

Cable diameter 0.91 cm (0.36 in.)

Dimensions 2.3 cm H x 3.8 cm W x 13.5 cm L (0.9 in. H x 1.5 in. W x 5.31 in. L)

Compatible instruments Sigma 910, 920, 930, 930 T, 950, 900 Max samplers and the

AV9000 interface modules for the FL series flow loggers and AS950 samplers

Specifications—AV9000 interface module

Velocity measurement

Measurement method 1 MHz Doppler Ultrasound

Doppler Analysis Type Digital Spectral Analysis

-1.52 to 6.10 m/s (-5 to 20 ft/s)

± 2% of reading or 0.05 fps (uniform velocity profile, known salinity,

positive flow. Field performance is site specific.)

Doppler Accuracy ±1% of reading or 0.025 fps(with electronically simulated Doppler signal,

-25 to +25 fps equivalent velocity). Refer to Configure the sensor

on page 14.

Power requirements

Supply voltage 9-15 VDC

Maximum current <130 mA @ 12 VDC with submerged area velocity sensor

Energy per measurement <15 Joules (typical)

Operating temperature

-18 to 60 ºC (0 to 140 ºF) at 95% RH

Enclosure

Dimensions (W x H x D) AV9000: 13 x 17.5 x 5 cm (5.0 x 6.875 x 2.0 in.)

AV9000S: 12.01 x 14.27 x 6.86 cm (4.73 x 5.62 x 2.70 in.)

Environmental Rating NEMA 6P, IP68

Enclosure material PC/ABS

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

4

English

Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

W A R N I N G

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

C A U T I O N

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol on the instrument is referenced in the manual with a

precautionary statement.

This is the safety alert symbol. Obey all safety messages that follow this symbol to avoid potential

injury. If on the instrument, refer to the instruction manual for operation or safety information.

This symbol indicates the presence of devices sensitive to Electro-static Discharge (ESD) and

indicates that care must be taken to prevent damage with the equipment.

Electrical equipment marked with this symbol may not be disposed of in European domestic or public

disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to

the user.

Confined space precautions

D A N G E R

Explosion hazard. Training in pre-entry testing, ventilation, entry procedures, evacuation/rescue

procedures and safety work practices is necessary before entering confined spaces.

The information that follows is supplied to help users understand the dangers and risks that are

associated with entry into confined spaces.

On April 15, 1993, OSHA's final ruling on CFR 1910.146, Permit Required Confined Spaces, became

law. This standard directly affects more than 250,000 industrial sites in the United States and was

created to protect the health and safety of workers in confined spaces.

Definition of a confined space:

A confined space is any location or enclosure that has (or has the immediate potential for) one or

more of the following conditions:

• An atmosphere with an oxygen concentration that is less than 19.5% or more than 23.5% and/or a

hydrogen sulfide (H

2

S) concentration that is more than 10 ppm.

• An atmosphere that can be flammable or explosive due to gases, vapors, mists, dusts or fibers.

• Toxic materials which upon contact or inhalation can cause injury, impairment of health or death.

English

5

Confined spaces are not designed for human occupancy. Confined spaces have a restricted entry

and contain known or potential hazards. Examples of confined spaces include manholes, stacks,

pipes, vats, switch vaults and other similar locations.

Standard safety procedures must always be obeyed before entry into confined spaces and/or

locations where hazardous gases, vapors, mists, dusts or fibers can be present. Before entry into a

confined space, find and read all procedures that are related to confined space entry.

Product overview

The submerged area velocity (AV) sensor is used with Sigma flow meters, FL series flow loggers and

AS950 samplers to measure the flow rate in open channels. Refer to Figure 1.

The sensor is available in oil-filled and non-oil-filled versions. The non-oil sensor is used for

reasonably clear sites, or sites where the pipe may become dry. The oil-filled sensor is used for sites

with high levels of biological growth, grit or silt.

Note: Do not use an oil-filled sensor in a pipe that may become dry.

The submerged AV sensor connects to a FL series flow logger or AS950 sampler through an

AV9000 interface module. Refer to Replacement parts and accessories on page 19 to identify the

applicable AV9000 model for the flow logger or sampler.

Note: The submerged AV sensor connects directly to Sigma flow meters. An AV9000 interface module is not

necessary.

Figure 1 Submerged area velocity sensor

1 Junction box (optional) 6 Lanyard

2 Desiccant hub 7 Submerged AV sensor

3 Desiccant container 8 Carabiner clip

4 Air reference tube 9 Sensor cable

5 Connector

Theory of operation

The sensor operates as an area velocity sensor and follows the continuity equation.

Flow rate = wetted area x average velocity

6

English

A pressure transducer in the sensor converts the pressure of the water to a level measurement. The

level measurement and the user-entered channel geometry are used to calculate the wetted area of

the flow stream.

The sensor also contains two ultrasonic transducers: one is a transmitter and the other is a receiver.

A 1 MHz signal is transmitted and reflected off of particles in the flow stream. The reflected signal is

received and its frequency is offset by the Doppler shift proportional to the velocity of the particles in

the flow stream. The flow logger converts the doppler shift in the returned ultrasound signals to a

velocity measurement.

Product components

Figure 2 shows the items in the shipment package. Contact the manufacturer if any components are

damaged or missing.

Figure 2 Product components

1 Submerged AV sensor 3 Junction box

2 Submerged AV sensor with junction box 4 Mounting screws (6x)

Installation

Installation guidelines

D A N G E R

Explosion Hazard. The non-IS AV sensors (770xx-xxx P/Ns) are not rated for use in classified Hazardous

Locations. For classified Hazardous Locations, use IS AV sensors (880xx-xxx PNs) installed per the control

drawings in 911/940 IS Blind Flow Meter manuals.

D A N G E R

Potential confined space hazards. Only qualified personnel should conduct the tasks described in this section of

the manual.

• Do not install more than one sensor in pipes with a diameter of less than 61 cm (24 inches).

Multiple sensors in smaller pipes can create turbulent or accelerated flows near the sensors, which

may cause inaccurate measurements.

• Mount the sensor as close as possible to the bottom of the pipe invert. This will give the most

accurate low-velocity-level measurements.

• Do not monitor flows in the manhole invert. The best location for the sensor is 3 to 5 times the

sewer diameter/height upstream of the invert.

• Put monitoring sites as far from inflow junctions as possible to avoid interference caused by

combined flows.

English

7

• Objects such as rocks, pipe joints, or valve stems create turbulence and generate high-speed

flows near the object. Make sure the area 2 to 4 pipe diameters in front of the sensor installation is

clear of obstructions. Best accuracy is obtained when there are no flow disruptions within 5 to

10 pipe diameters.

• Do not use sites with low-velocity flows that create silt buildup in the invert or channel. Buildup of

silt near the sensor can inhibit the Doppler signal and cause inaccurate sensor readings and depth

measurements.

• Do not use sites with deep rapid flows where sensor installation would be difficult or dangerous.

• Do not use sites with high-velocity, low-depth flows. Splash-over and excessive turbulence around

the sensor can cause inaccurate data.

Interference

The AV9000 interface module includes a sensitive radio-frequency receiver capable of the detecting

very small signals. When connected to a flow logger or sampler communications or auxiliary power

ports, some line-powered equipment can add electrical noise that interferes with Doppler velocity

measurements. Interference with measurements is uncommon in typical sites.

The AV9000 is most sensitive to noise falling within its Doppler analysis span of 1 MHz ± 13.3 kHz.

Noise at other frequencies typically does not cause interference.

Some laptop computers can cause interference problems when operated from external AC power

adapters. If such a device has an effect on the measurements, operate the laptop computer with

batteries or disconnect the cable between the laptop computer and the flow logger or sampler.

Install the AV9000 interface module

The submerged AV sensor connects to a FL series flow logger or AS950 sampler through an

AV9000 interface module. Refer to Replacement parts and accessories on page 19 to identify the

applicable AV9000 interface module for the flow logger or sampler.

Note: The submerged AV sensor connects directly to Sigma flow meters. An AV9000 interface module is not

necessary.

1. Install the AV9000 interface module. Refer to the AV9000 documentation for instructions.

2. Connect the sensor cable to the AV9000 interface module. Refer to the AV9000 documentation

for instructions.

3. Connect the AV9000 cable to a sensor port (or terminal) on the flow logger or sampler. Refer to

the flow logger or sampler documentation for instructions.

Attach the desiccant hub

Attach the desiccant hub to the flow logger or sampler to give strain relief to the sensor cable and the

connector. Refer to Figure 3 to Figure 5.

For the best performance, make sure to install the desiccant container vertically with the end cap

pointed down. Refer to Figure 3 to Figure 5.

8

English

Figure 3 Attach the desiccant hub—FL900 flow logger

1 End cap

Figure 4 Attach the desiccant hub—FL1500 flow logger

1 AV9000S with bare-wire connection 3 End cap

2 Accessories mounting plate

English 9

Figure 5 Attach the desiccant hub—AS950 portable sampler

1 End cap

Zero level calibration

If one or more of the statements that follow are correct, do a zero level calibration before the sensor

is installed.

• The installation location is a dry channel.

• It is not possible to get an accurate level in the flow because the level changes too rapidly.

• It is not possible to get an accurate level in the flow because of physical hazards.

Note: The sensor is factory-calibrated for the specified range and temperature.

Zero level calibration (FL series flow logger or sampler)

To do a zero level calibration with an FL900 flow logger, do a zero level calibration (zero calibration

in air) with the FSDATA Desktop Setup Wizard. Refer to the FSDATA Desktop documentation for

instructions. As an alternative, do a manual zero level calibration (zero calibration in air) with

FSDATA Desktop.

To do a zero level calibration with the FL1500 flow logger or sampler, refer to the FL1500 flow logger

or sampler documentation for instructions. As an alternative, do a zero level calibration with the

FSDATA Desktop Setup Wizard when the sensor is connected to an FL1500 flow logger.

Make sure that the sensor is out of the water and on a flat, level, horizontal surface.

Note: If the sensor is replaced, removed for maintenance or moved to another instrument, do a zero level

calibration.

10

English

Zero level calibration (Sigma 910 to 950 flow meters)

Do a zero level calibration as follows:

Note: If the sensor is replaced, removed for maintenance or moved to another instrument, do a zero level

calibration again.

1. Connect the flow meter to a computer with InSight software. Refer to the flow meter

documentation for instructions.

2. Start the InSight software on the computer.

3. Select Remote Programming.

4. From the Real Time Operations list, select the level sensor.

5. Remove the probe from the liquid and place the sensor flat on the tabletop or floor with the

sensor (the plate with holes) face down.

6. Push OK on the dialog box when complete.

Attach the sensor to the mounting band

Mounting bands have pre-drilled holes for direct mounting of the sensor to the band. Refer to the

steps and the figures to mount the sensor on the mounting band.

Note: If the sensor is the oil-filled type, make sure the sensor is filled with oil before mounting the sensor to the

mounting band. Refer to the Fill sensor oil section of this manual.

1. Attach the sensor to the spring ring (Figure 6). Mount the sensor so that the pressure transducer

extends past the edge of the ring.

2. Route the cable along the edge of the band (Figure 6).

3. Use nylon-wire ties to fasten the cable to the mounting band.

The cable should exit the tied area at or near the top of the pipe.

Note: If a large amount of silt exists in the bottom of the pipe, rotate the band until the sensor is out of the silt

(Figure 8 on page 14). Make sure the sensor remains below the minimum expected water level at all times.

Silt must be measured frequently but not disturbed.

English

11

Figure 6 Attach the sensor to the mounting band

1 Sensor 3 Sensor cable

2 Spring ring 4 Screws (2)

Place the sensor and mounting band in the pipe

1. Position the sensor in the flow. Figure 7 shows a standard upstream configuration, a standard

downstream configuration and a downstream sensor-reversed configuration.

To help determine the best configuration for the site, refer to Table 1. For more information on

configurations, refer to the appropriate logger manual.

2. Slide the mounting band inside the pipe as far as possible to prevent drawdown effects near the

end of the pipe.

3. Place the sensor at the bottom-most point in the channel. If excessive silt is present on the

bottom of the pipe, rotate the band in the pipe until the sensor is out of the silt. Refer to Figure 8.

12

English

Figure 7 Sensor positions

1 Upstream, facing flow 2 Downstream, facing flow 3 Downstream, reversed

Table 1 Selecting probe direction

Option Description

Upstream Recommended for most applications. The flow stream over the sensor should be as straight

as possible with no drops or turns near the measurement point.

Mount the sensor in the pipe with the beveled edge pointed toward the flow where the flow

stream enters the measurement area.

Downstream Use this option when the sensor is installed downstream of the measurement point (where

the flow stream exits the site). This option is useful when more than one flow stream enters a

site and the combined flow of all streams is measured at a single exit point. This option can

also be used if there are hydraulics preventing the sensor from being mounted in upstream

area.

Mount the sensor facing the flow.

Downstream

(reversed sensor)

Use this option when Option B will not work due to poor flow uniformity in the vault. The

maximum velocity read in this kind of installation is 5 fps when the AV9000 interface module

is not used. Mount the sensor in the downstream direction. The manufacturer recommends

verifying the velocity by profiling flow and using a velocity site multiplier, if required, for more

accurate reading.

Note: When the AV9000 interface module and submerged AV sensor are used with the FL900 logger, the

user has the option to select Reversed Sensor on the Sensor Port Set Up menu.

English 13

Figure 8 Avoiding silt when mounting the sensor

1 Water 3 Sensor

2 Pipe 4 Silt

Operation

For sensors connected to an FL900 flow logger, connect a computer with FSDATA Desktop software

to the flow logger to configure, calibrate and collect data from the sensors. Refer to the FSDATA

Desktop documentation to configure, calibrate and collect data from the sensor.

For sensors connected to an FL1500 flow logger, refer to the FL1500 flow logger documentation to

configure, calibrate and collect data from the sensors. As an alternative, connect a computer with

FSDATA Desktop software to the flow logger to configure, calibrate and collect data from the

sensors. Refer to the FSDATA Desktop documentation to configure, calibrate and collect data from

the sensor.

For sensors connected to an AS950 sampler, refer to the AS950 sampler documentation to

configure, calibrate and collect data from the sensors.

For sensors connected to a Sigma 910, 911, 920, 930 or 940 flow meter, connect a computer with

InSight software to the Sigma flow meter to configure, calibrate and collect data from the sensors.

Install the software

Make sure that the latest version of the FSDATA Desktop software or InSight software is installed on

the computer as applicable. Download the software from http://www.hachflow.com. Click Support,

then select Software Downloads.

Configure the sensor

For sensors connected to an FL900 flow logger, configure the sensors with the FSDATA Desktop

Setup Wizard. Refer to the FSDATA Desktop documentation for instructions.

14

English

For sensors connected to an FL1500 flow logger or AS950 sampler, refer to the FL1500 flow logger

or sampler documentation to configure the sensors. As an alternative, configure the sensors with the

FSDATA Desktop Setup Wizard when the sensors are connected to an FL1500 flow logger.

For sensors connected to a Sigma flow meter, do the steps in Level calibration for Sigma flow meters

on page 15.

Note: If a sensor is replaced, removed for maintenance or moved to another instrument, do a level calibration.

Level calibration for Sigma flow meters

1. With the sensor installed in the flow, monitor the Current Status with a PC using Insight software

or a flow meter display.

2. Physically measure the distance from the top of the pipe to the surface of the water. Refer to

Figure 9.

3. Subtract the number from step 2 from the pipe diameter. Refer to Figure 9.

The result is the water depth. Refer to Figure 9.

4. Use the Adjust Level function of the software to enter the physically-measured water depth.

Figure 9 Measure the water level

1 Water level

Maintenance

C A U T I O N

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

Clean the sensor

Clean the transducer port when:

• Unexpected increases or decreases in flow or level trends occur

• Level data are missing or incorrect but velocity data are valid

English

15

• Excessive silt deposits have built up between the transducer and the protective cover

Notes

• Do not touch the sensor transducer as this will cause damage and incorrect sensor operation.

• Use only approved cleaning solutions as listed in Table 2. Do not use any type of brush or rag to

clean the pressure transducer as this will cause damage and incorrect sensor operation. If there

are debris, spray the membrane with water and use a Q-tip to carefully remove the buildup.

• If the gasket is missing or damaged, install a new one. A damaged or missing gasket will cause

inaccurate readings.

• After cleaning the sensor, clean the gasket and protective cover before they are installed.

• After cleaning an oil-filled sensor, replenish the sensor oil.

• If a sensor must be taken out of service for an extended period, do not store the sensor on a dry

shelf. The manufacturer recommends that the sensor be stored with the sensor head in a bucket

of water to keep the oil debris from crusting in the pressure transducer canal.

To clean the sensor:

1. Soak the sensor in soapy water.

2. Remove the screws from the protective cover. Refer to Figure 10.

3. Remove the cover and gasket. Refer to Figure 10.

4. Carefully swirl the sensor in an appropriate cleaning solution to remove soil. Use a spray or

squeeze bottle to wash away heavier deposits.

5. Clean the gasket and cover.

6. Attach the gasket and cover. tighten the screws until the gasket starts to compress.

Figure 10 Sensor protective cover and gasket

1 Protective cover 2 Gasket 3 Sensor

16 English

Table 2 Acceptable and unacceptable cleaning solutions

Acceptable Do not use

Dish detergent and water Concentrated bleach

Window cleaner Kerosene

Isopropyl alcohol Gasoline

Dilute acids Aromatic hydrocarbons

Replace the desiccant

N O T I C E

Do not operate the sensor without desiccant beads or with green desiccant beads. Permanent damage to the

sensor can occur.

Immediately replace the desiccant when it changes to green. Refer to Figure 11.

Note: It is not necessary to remove the desiccant container from the desiccant hub to install new desiccant.

At step 5 of Figure 11, make sure that the O-ring is clean and has no dirt or debris. Examine the O-

ring for cracking, pits or sign of damage. Replace the O-ring if it has damage. Apply grease to dry or

new O-rings to make installation easier, to get a better seal and to increase the life of the O-ring.

For the best performance, make sure to install the desiccant container vertically with the end cap

pointed down. Refer to Attach the desiccant hub on page 8.

Note: When the beads just begin to turn green, it may be possible to rejuvenate them by heating. Remove the

beads from the canister and heat them at 100-180 ºC (212-350 ºF) until they turn orange. Do not heat the canister.

If the beads do not turn orange, they must be replaced with new desiccant.

Figure 11 Replace the desiccant

English 17

Replace the hydrophobic membrane

Replace the hydrophobic membrane when:

• Unexpected increases or decreases in level trends occur.

• Level data is missing or incorrect, but the velocity data is valid.

• The membrane is torn or has become saturated with water or grease.

Refer to the illustrated steps that follow to replace the membrane. At step 4, make sure that the

following occurs:

• The smooth side of the hydrophobic membrane is against the inner surface of the desiccant

container.

• The hydrophobic membrane bends up and goes fully into the thread until it is not seen.

• The hydrophobic membrane turns with the nipple when the nipple in the desiccant container turns.

If the membrane does not turn, it has damage. Start the procedure again with a new membrane.

For the best performance, make sure to install the desiccant container vertically with the end cap

pointed down. Refer to Attach the desiccant hub on page 8.

18 English

Replenish the sensor oil

Inspect the oil in the sensor for large air bubbles during customer-scheduled service duty cycles.

Large bubbles can reduce the anti-fouling properties of the oil. Small bubbles (< ¼-in. diameter) do

not affect the oil properties.

To replenish the sensor oil, refer to the documentation supplied with the silicone oil refill kit. Refer to

Replacement parts and accessories on page 19 for ordering information.

Replacement parts and accessories

W A R N I N G

Personal injury hazard. Use of non-approved parts may cause personal injury, damage to the

instrument or equipment malfunction. The replacement parts in this section are approved by the

manufacturer.

Note: Product and Article numbers may vary for some selling regions. Contact the appropriate distributor or refer to

the company website for contact information.

Replacement parts

Description Item number

Desiccant beads, bulk, 1.5 pound canister 8755500

Desiccant container 8542000

Hydrophobic membrane 3390

O-ring, dessicant container end cap, 1.176 ID x 0.070 OD 5252

Silicon oil, includes two 50-mL oil packs to refill 100 sensors 7724700

English 19

Description Item number

Silicon oil refill kit, includes:

dispensing tool, two 50-mL oil pack, instruction sheet and miscellaneous hardware

7724800

Desiccant hub

1

7722800

Accessories

Description Item number

AV9000 interface module, FL900 flow loggers 8531300

AV9000S interface module with bare-wire connection, FL1500 flow loggers 9504601

AV9000S interface module, AS950 portable samplers 9504600

Accessories mounting plate, FL1500 flow loggers 8309300

Custom cable, sensor to junction box, 0.3 to 30 m (1 to 99 ft) 77155-PRB

Custom cable, junction box to desiccant hub, 0.3 to 30 m (1 to 99 ft) 77155-HUB

Silicone potting gel kit for junction box 7725600

Gel fill, silicone potting

2

7729800

Gel fill, dispenser gun

3

7715300

Retrofit kit, change a sensor with a non-oil cover plate to a sensor with an oil-filled cover plate,

includes 7724800

7730000

Insertion tool, street-level installation of mounting rings 9574

Mounting ring for ∅ 15.24 cm (6 in.) pipe

4

1361

Mounting ring for ∅ 20.32 cm (8 in.) pipe

4

1362

Mounting ring for ∅ 25.40 cm (10 in.) pipe

4

1363

Mounting ring for ∅ 30.48 cm (12 in.) pipe

5

1364

Mounting ring for ∅ 38.10 cm (15 in.) pipe

5

1365

Mounting ring for ∅ 45.72 cm (18 in.) pipe

5

1366

Mounting ring for ∅ 50.8 to 53.34 cm (20 to 21 in.) pipe

5

1353

Mounting ring for ∅ 61 cm (24 in.) pipe

5

1370

Mounting band selection chart

Pipe diameter Mounting Band Selection

6

Item number

1473--6.25"

(15.85 cm) long,

adds 2" (5.08 cm) to

band diameter

Item number

1525--9.5"

(24.13 cm) long,

adds 3" (7.62 cm) to

band diameter

Item number

1759--19" (48.26 cm)

long, adds 6"

(15.24 cm) to band

diameter

Item number

1318--50.25" (127 cm)

long, adds 16"

(40.64 cm) to band

diameter

1

Use part number 77155-HUB to select the cable length after the desiccant hub.

2

Order three to fill one junction box.

3

Can also be used as a silicone oil fill gun

4

Requires item number 3263

5

The sensor attaches directly to band.

6

In addition to the band segments shown below, a complete mounting band assembly requires

one AV Sensor Mounting Clip (3263) and one Scissors Jack Assembly (3719).

20 English

Sayfa yükleniyor ...

Hach AV9000 Kullanım kılavuzu

Bu kılavuz için de uygundur

Hach AV9000 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler