LG VR5942L Kullanici rehberi

Tip
Kullanici rehberi
Model
Language
Page
)H*W(eziSlairetaM
Designer
Designer
Confirm
Color(cover/body)
Part No
Date
etaD.oN
Chage Record
Change content
ECO No.
1
2
3
4
5
6
7
8
9
Weight 80g
201 . .26
V
English
MFL6708605 Description
1/1
190×260(mm)
Owners Manual
Turkish
OWNER’S MANUAL
HOM-BOT
VR5942L
Before using, please carefully read the Safety Precautions pages to allow for
safe operation of the product. After reading the operation manual, please keep
it in an easily accessible location.
www.lg.com
DUTCHENGLISH TURKISHENGLISH
FEATURES
Images of the floor are obtained from the sensors of the lower camera, and
through this, the location of HOM-BOT will be confirmed,therefore, elaborate
cleaning can be accomplished for every part of the room.
As the height of the HOM-BOT is low (90mm), even the underside of a framed
bed or furniture can be cleaned.
The HOM-BOT also has voice confirmation and instruction that can be easily
understood by the user.
The HOM-BOT can clean all parts of the area by cleaning in zigzag mode and
then in spatial expansion mode.
As the noise levels are at a quiet 60dB(A), cleaning can be performed at night.
*Less than 60dB(A)
Camera sensor
Please, check
the dust bin
CONTENTS
Safety Precautions
Included with Product
Parts Descriptions
Button Functions
Display Status Information
Before You Start
Overview
1
BEFORE USING
2
HOW TO USE
3
CARE AND MAINTENANCE
26~28
29
How to Install the Home Station
How to Turn the Power Supply On and Off.
How to Start and Stop Cleaning
How to Charge the Battery
Cleaning Modes
Auxiliary Cleaning Modes
Timer Cleaning
Cleaning the Dust Bin
Cleaning the Dust Bin Filter
Cleaning the Brush
Cleaning the Sensor/Charging Terminal
Cleaning the Side Brush
4
ADDITIONAL INFORMATION
5
REFERENCE
1~4
5
6~7
8~9
10
11
12
13
14
15
16~17
18
19
20
21
22
23
24
25
Troubleshooting
Before You Call for Service
Product Specifications
30
ENGLISH
SAFETY PRECAUTIONS
The purpose of the safety precautions described below is for the user to use the product safely and correctly
to prevent any unexpected risk or damage.
Basic safety precautions
After reading this manual, please keep it in an easily accessible location.
This is the safety alert symbol. This symbol alerts you to potential hazards that can result in prop-
erty damage and/or serious bodily harm or death.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
WARNING
WARNING
CAUTION
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
If the supply cord is damaged, it must be replaced by
LG Electronics Service Agent in order to avoid a hazard.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user mainte-
nance shall not be made by children without supervi-
sion.
1.
2.
3.
4.
1
For your safety, do not remove the battery
from the HOM-BOT. If you need to replace the
battery or the HOM-BOT, take it to the nearest
authorized LG Electronics service center or
dealer for assistance.
Make sure the power cord of the home sta-
tion is not crushed under a heavy object or
damaged by contact with sharp objects.
Never use the HOM-BOT with a bat-
tery and/or home station from any
other product than the HOM-BOT.
Failure to follow this warning can cause fire or
product failure. If the power cord is broken,
replace it at an LG Electronics customer care
center.
Do not use the HOM-BOT when
candles or fragile objects are placed
on the floor.
Doing so can cause fire or product failure.
Failure to follow this warning can cause fire
or product failure.
Doing so can cause fire or product failure.
Do not place the home station and
the HOM-BOT near a heating device.
Always use a dedicated outlet.
Doing so can cause product deformation,
fire, or product failure.
If multiple appliances are connected to an
outlet simultaneously, they can generate
enough heat to cause a fire.
Do not force the power plug to bend.
Do not use the power plug when it
has been damaged or loosened.
When pulling out the power plug, always
pull it out by grabbing the plug, not the
cord. When pulling out the power plug, do
not to touch the prongs with your fingers.
Doing so can cause fire or product failure.
Doing so can cause an electric
shock.
SAFETY PRECAUTIONS
2
Do not touch the power plug with
wet hands.
Do not use the HOM-BOT while a
child or object is on it. Do not use the
HOM-BOT while an object is hanging
from it.
Doing so can cause electric shock.
Doing so can cause injury or product dam-
age.
ENGLISH
SAFETY PRECAUTIONS
Do not operate the HOM-BOT in a room
where a child is sleeping.
Doing so can cause injury or product dam-
age.
Do not insert any part of the body, such as
a hand or foot, below the brush or wheels
of the HOM-BOT while in use.
Doing so can cause injury or product damage.
Do not spray or suck in inflammable
materials, surfactants, or drinking wa-
ter in the vicinity of the HOM-BOT.
Doing so can cause fire or product failure.
*
Inflammable materials: gasoline, thinner, etc.
*
Surfactant: detergent, articles for bath, etc.
Turn the power supply off immediately if
any abnormal sound, odor, or smoke is
generated from the HOM-BOT.
Failure to do so can cause fire or product
failure.
Do not operate the HOM-BOT on nar -
row and high furniture such as a ward-
robe, refrigerator, desk, table, etc.
Doing so can cause injury or product failure.
Do not let children play with the
HOM-BOT.
Doing so can cause injury or product dam-
age.
Do not expose the HOM-BOT to
cold temperatures (less than 23°F
or -5°C) for a long period of time.
Use the HOM-BOT indoors only.
Doing so can cause product failure.
Using it outdoors can cause prod-
uct failure.
The dust collected in the dust bin
can trigger allergies and may contain
harmful insects.
Frequently empty the dust bin and
maintain its cleanliness.
Do not drop the HOM-BOT or sub -
ject it to strong impacts.
Doing so can cause injury or product failure.
WARNING
CAUTION
Cleaning will not proceed smoothly
on carpets with tassels or carpets
thicker than 10 mm.
The HOM-BOT may bump into fur -
niture such as chair legs, table legs,
thin and long furniture, etc. while
operating.
It may be more convenient to
arrange them before using the
product.
For a quicker and cleaner performance,
place the chairs on top of the table.
3
SAFETY PRECAUTIONS
In rare cases, the HOM-BOT brush
can damage the carpet. If this hap-
pens, immediately stop the cleaning
operation.
When a carpet has long tassels, the
tassels can be damaged.
Do not allow the HOM-BOT to suc -
tion up liquids, blades, thumb tacks,
kindling, etc.
These items can cause product
failure.
Do not let the main frame and charg-
ing terminal of the home station come
into contact with metallic objects.
Doing so can cause product failure.
Do not put sharp objects into the
opening of the HOM-BOT super -
sonic sensor.
Doing so can cause product failure.
Do not put water, detergent, etc.
into the HOM-BOT.
Doing so can cause product failure. Do not
put any water or detergent on the HOM-BOT.
If liquids get inside of the HOM-BOT, turn off
the power supply and contact an LG Electron-
ics sales agent or customer care center.
Do not use the HOM-BOT when the
dust bin is completely filled up.
Doing so can cause product failure.
If the floor is wet or has wet spots,
wipe them up before using the
HOM-BOT.
Failure to do so can cause product
failure.
Check the following items before use:
Remove fragile or unnecessary objects from the room to be cleaned. For example, remove
expensive ceramics and valuables from the floor.
ot use this product in the room where a child is sleeping alone. The child can be hurt.
Confirm whether the battery has sufficient power, and if it is low, recharge it.
Empty the dust bin after if fills up.
Close the doors of any room that you do not want the HOM-BOT to enter.
During cleaning, the HOM-BOT may enter another room and continue cleaning.
Remove any moisture from the floor before cleaning.
Remove any cables or long strings from the floor.
Remove cables, strips, towels, socks, etc. from the floor so they will not get caught by the brush.
Cleaning will not proceed smoothly on carpets with tassels or carpets thicker than 8 mm
(0.315 in). It may be more convenient to arrange them before using the product.
Tip
CAUTION
Please note, this product is not intended for use in any workshop, commercial office, garage or outdoor
environment. It is for normal Domestic internal home use only.
4
ENGLISH
If you do not use it to save the
energy, turn off the power switch,
and turn on the power switch when
you are cleaning or recharging it
HOM-BOT
PARTS DESCRIPTION
Figures can be different from actual objects.
Top view
Dust bin cover button
Dust bin cover
Ultrasonic sensor
Ventilation port
Cliff detection sensor
Charging terminal
Brush
Side brush
Wheel
Lower camera sensor
Battery
Power switch
Status indication lamp
Detecting sensor of home station &
receiving sensor of remote controller
Front view
Rear view
Bottom view
6
ENGLISH
PART DESCRIPTION – HOME STATION / DUST BIN
Figures can be different from actual objects.
Home station
Dust bin
Power lamp
Charging terminal
Reset button
Sponge
filter
HEPA filter
Dust bin handle
Dust bin cover
Suction port cover
Dust bin cover opening
button
Power cord fixing groove
7
BUTTON FUNCTIONS
START/STOP
Pres START/ST HOM-BOT /o s r /s e
Pres START/ST on HOM-BOT
s r e
START/ST ress e HOM-BOT
s e
Pres START/ST on ro w se
o HOM-BOT.
HOM-BOT S B
ressed se
8
ENGLISH
BUTTON FUNCTIONS – REMOTE CONTROL
The HOM-BOT power supply cannot be turned on with the remote control.
To turn on the power supply, use START/STOP button on the top of HOM-BOT.
In order to do spot cleaning, timer cleaning, zigzag cleaning, and spatial expansion cleaning, you
must first stop the operation of the HOM-BOT.
frame is turned off, the remote control will not be activated.
The preset feature may be set only when the HOM-BOT returns to the charging stand.
If the main switch on the underside of the HOM-BOT is in the off position, the Status display will
flash and sound when the unit is manually placed onto the home station, to indicate that the
main switch is off.
Tip
Directional button
STOP
HOMING
SPOT
TIMER
Zigzag cleaning and then
spatial expansion
The HOM-BOT ehTgninaelc tratslliw HOM-BOT will move to the
home station for charging.
The HOM-BOT will move as desired
by the user: to front, rear, left, and
right sides for cleaning.
If the HOM-BOT is in operation it will
be stopped. If it has been set for
timer cleaning, the reservation will be
canceled.
Cleaning will concentrate within a
space of about 1 m (3.28 ft).
The timer can be set from 1-12
hours in the future.
The HOM-BOT will clean while ma-
neuvering in a zigzag pattern and
then expand the cleaning area.
9
START
DISPLAY STATUS INFORMATION
T canc se es ST o c START/ST
HOM-BOT.
Tip
Battery and reserved time indi-
cation
Timer icon
Battery icon
w f e -
a e evel own.
w f e
ese va own.
ca es e
se .
es a e e
e
s a c e
cle
10
ENGLISH
BEFORE YOU START
Check these items before cleaning
Loading the remote control battery
1. Open the battery cover by lifting the rear hook of the remote control.
2. Insert two AAA batteries, checking for +, - nodes while loading.
3. Close the battery cover completely so that the batteries will not fall out.
ţ%POot use this device in a room where a child is left alone. The child could be injured.
ţRemove fragile or unnecessary objects from the room to be cleaned.
Especially, remove expensive ceramics and valuables from the floor.
ţRemove any moisture that might be on the floor.
ţRemove cables, strips, towels, socks, etc. from the floor so they will not get caught by the brush.
ţConfirm whether battery charge is sufficient, and if it is low, recharge it.
ţEmpty the dust bin if it is full.
ţClose the doors of any room that you do not want the HOM-BOT to enter. %uring cleaning, the HOM-BOT
may enter another room and continue cleaning.
ţWhen the mop is attached, HOM-BOT will not be able to go over thresholds of 5mm or higher.
If you are not planning to use the mop for cleaning, remote the mop before using HOM-BOT.
Precautions while using the remote control
ţ0OMZQress one button at a time.
ţ%POot drop or subject it to forceful impact.
ţ%POot store it near devices that give off heat, fire or hot air.
ţCertain fluorescent lamps, such as 3 wavelength fluorescent lamps, can interfere with the activation of the
remote control. Therefore, use it as far away as possible from such lamps.
ţIf the remote control is far from the HOM-BOT when activated, it may fail to operate properly. Use the device
within 3 m (9.84 ft) of the HOM-BOT if possible.
11
OVERVIEW
1
Install the home station. (page 13)
Insert the power cord plug into an outlet and locate the
station against a wall. If power is not supplied to the
home station, the HOM-BOT will not charge.
2
Turn on the power supply of the HOM-BOT. (page 14)
Turn on the power switch located on the bottom of the
Roboking and press the upper START/STOP button to
turn on the power supply.
* If the power supply is not turned on, refer to page 14.
3
Start cleaning. (page 15)
Press the START/STOP button once again while the
HOM-BOT is turned on. You will hear the sound of clean-
ing and cleaning will begin.
4
Automatic charge. (page 16-17)
The HOM-BOT will self-diagnose and automatically return
to the home station to recharge before the complete dis-
charge of the battery. It takes approximately three hours
to charge the battery.
5
Use auxiliary functions. (page 18-21)
With the remote control, the auxiliary functions can be
used. Auxiliary functions include manual cleaning, spot
cleaning, the timer function, and ultra microfiber mop
cleaning.
1.5m
1.5m
2m
12
ENGLISH
1. Position the home station against a wall, to prevent sliding dur-
ing docking, on hard level flooring.
nihtiwdnaedistfeldnathgirehtot.m5.1nihtiwstcejboevomeR
2m. to the front.
2. Plug the power cord into an outlet.
Wrap the power cord around the fixed hanger on the back side
of the home station or along the wall surface so that the travel
path of the HOM-BOT will not be obstructed.
3. Fix the home station against the wall so that it does not move.
Turn on the power switch.
How to Install the Home Station
Always keep the home station plugged in. If the home station is not plugged in, the HOM-BOT
will not return to the station to charge automatically.
Do not operate the HOM-BOT if it has a damaged cord or plug, if it is not working properly, or
if it has been damaged or dropped. To avoid hazard, the cord must be replaced by LG Elec-
tronics, Inc. or a qualified service person.
HOW TO INSTALL THE HOME STATION
Tip
Fixing groove of power cord
1.5m
1.5m
2m
13
HOW TO TURN THE POWER SUPPLY ON AND OFF.
To turn the power supply on, turn the HOM-BOT upside down on
a smooth/soft surface and check whether the main power sup-
ply switch is turned on.
If the main power supply switch is turned off, turn on the
switch.
When turning on the power switch, do not press the button
located at the upper section of the HOM-BOT. Operation of the
button can be delayed.
Turn off the power switch if the HOM-BOT will not be used for
a long period of time, in order to protect the battery.
The power switch cover is used for protecting the switch
from the dust. Always keep the cover attached on.
When HOM-BOT is not turned on, press the ‘START/
STOP’ button for more than 1 second. The power supply
will be turned on with the melody sound.
If the power supply is turned on and nothing is done for
ten minutes, the power supply will automatically turn off
to reduce battery consumption.
Press the START/STOP button for two seconds while the
HOM-BOT is turned on. A melody will sound when the
power is turned off. The power will be turned off with the
melody sound.
Turning on the main power supply
Turning on the power supply
Turning off the power supply
The power can be turned off due to the static electricity during
the operation.
- If the power is turned off, turn off the main power switch and
then turn it back on.
ower cannot be turned on, do the following.
- Turn on the power switch and wait for more than 3 seconds.
- Press the ‘START/STOP’ button when the power switch is
turned on.
- If the power is not turned on or if there is no display but only
the “Ting” sound, put the HOM-BOTon the home station.
- If there is no change even when HOM-BOT is attached to the
home station, press the reset switch located on the rear side
of the home station while the HOM-BOT is attached on the
home station.
Tip
14
ENGLISH
After the HOM-BOT is turned on, press the START/STOP button to
begin cleaning. A melody will sound and cleaning will begin.
Press the START/STOP button during the cleaning cycle to stop cleaning.
When the ‘START/STOP button is pressed while the power supply
of the HOM-BOT is turned off, the power will be turned on. Press the
‘START/STOP’ button one more time to clean.
After the HOM-BOT is turned on, press the START button on the re-
mote control. A melody will sound and cleaning will begin.
Press the STOP button during the cleaning cycle to stop cleaning.
The HOM-BOT power supply cannot be turned on by using the re-
mote control if the power of the HOM-BOT is off. When the power is
off, press the ‘START/STOP button on the upper side of HOM-BOT
to turn the power on.
When the START button on the main unit or remote control is pressed, HOM-BOT will start cleaning in
‘Spatial expansion’ mode.
During cleaning, collisions can happen when the sensor cannot detect objects because of their shape.
When this happens, the internal impact detecting sensor will avoid the obstacles by using a backward mo-
tion.
If the HOM-BOT is set to start cleaning at a location away from the home station, put the device on a flat floor
in order to prevent a malfunction of the obstacle detecting sensor. In addition, start cleaning from a location
where there are not any obstacles such as curtains or walls within 30 cm (11.8 in) of the HOM-BOT.
Using the buttons on the HOM-BOT
Using the remote control
For best results:
Briefly scan the area to be cleaned for big and small objects that will cause difficulty if vacu-
umed up.
If cleaning is started when the HOM-BOT is at the home station, the device can rapidly be re-
turned to the home station as the current home position has been accurately read.
HOW TO START AND STOP CLEANING
Tip
15
HOW TO CHARGE THE BATTERY
The HOM-BOT returns to the home station at the end of a cleaning cycle
or when its battery is running low.
If the HOM-BOT is unable to dock to the home station on its first at -
tempt, it will try again until it docks successfully.
When HOM-BOT completed all areas that it can clean, it will return
to the home station even when the battery level is not low.
Automatic charging
If using the HOM-BOT for the rst time or when charging the battery during cleaning, you can manually
charge the battery.
Method 1. Attach the HOM-BOT to the home station by matching
up the two arrows on the HOM-BOT and the home sta-
tion. A melody will sound and charging will begin.
When the HOM-BOT is attached to the home station, if a
“TING” sound is generated repeatedly, please check the
power switch and turn it on.
Method 2. When the HOMING button of the remote control or the
HOM-BOT is pressed, charging will start by automatically
generating a searching sound and returning the HOM-BOT
to the home station.
If the HOM-BOT stays within 10 cm (3.9 in) of the front of the charging terminal while the power supply is
turned on, it will automatically be returned to the home station and charging will begin.
Manual charging
Take the following precautions when using the home station:
If foreign material is caught in the charging terminal, charging may not proceed smoothly.
Wipe the terminal from time to time with a dry cloth after the power plug is disconnected.
To prevent electric shock, do not touch the charging terminal with any metallic objects.
To avoid fire or electric shock, never disassemble or modify the home station.
Do not to place the home station or power plug near to a heating appliance.
Tip
16
ENGLISH
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73

LG VR5942L Kullanici rehberi

Tip
Kullanici rehberi

Diğer dillerde