Blackmagic ATEM Microphone Converter Kullanım kılavuzu

Tip
Kullanım kılavuzu
ATEM
Microphone
Converter
ATEM Microphone Converter
December 2023
Installation and Operation Manual
Languages
To go directly to your preferred language, simply click on the hyperlinks listed in the
contents below.
English 3
日本21
Français 40
Deutsch 59
Español 78
中文 97
국어 116
Русский 135
Italiano 154
Português 173
rkçe 192
Polski 211
Українська 230
Welcome
Thank you for purchasing ATEM Microphone Converter!
ATEM Microphone Converter is an extremely high quality analog to digital audio
converter formultiple microphone sources.
The combined XLR/TRS inputs allow XLR or jack cables to be connected,
embedding the 4 analog inputs as MADI channels 1, 2, 3 and 4. The MADI input
allows multiple ATEM Microphone Converters to be daisy chained so more than
4channels ofaudio can be embedded into a single MADI connection!
Your converter features ultra high dynamic range input conversion so you get an
extremely low noise floor of -129dBV and all mic level sources can be individually
adjusted using a discrete digital preamplifier. Phantom power and mic or line audio
inputlevels can be set using the small built in switches, plus the HDMI monitoring
outputlets you visually see waveforms, audio levels and settings for each source.
This instruction manual shows you how to get started with your ATEM
MicrophoneConverter.
Check the support page on our website at www.blackmagicdesign.com for the
latestversion of this manual and for updates to your ATEM Microphone Converters
internal software. Whendownloading the software, be sure to register with your
informationso we can keep you updated when new software is released. Weare
continually working on new features and improvements, so we are keen to
hear from you!
Grant Petty
CEO Blackmagic Design
English
Contents
Getting Started 5
Connecting Power 5
Connecting Audio 6
Connecting to an ATEM Switcher 7
Connecting a Monitor 7
Settings  8
Blackmagic Converters Setup 8
Audio Settings 9
Setup Settings 10
Updating Blackmagic Converters Setup utility 12
Changing Settings Using Switches 12
Using the Monitor Output 13
Connecting Additional Converters 14
Mounting ATEM Microphone Converter 16
Help  17
Regulatory Notices 18
Safety Information 19
Warranty  20
4ATEM Microphone Converter 4
Getting Started
Getting started with your ATEM Microphone Converter is as simple as plugging in power,
connecting analog audio sources and plugging the MADI output into an ATEM switcher.
ATEM
MICROPHONE
CONVERTER
POWER +12V
ETHERNET
USB
MADI IN
MADI OUT
MONITOR OUT
MIC/LINE 1
MIC/LINE 2
MIC/LINE 3
MIC/LINE 4
Connecting Power
Connect the included 12 volt power supply to the power input using the socket adapter for your
country. Tightening the locking ring secures the cable to prevent accidental disconnection.
Connect power to your ATEM Microphone Converter using the supplied power adaptor
5Getting Started
Connecting Audio
Connect your audio sources to your converter via the combo XLR and 1/4” jack inputs.
Connect mic or line level analog audio to the ATEM Microphone Converter’s XLR or TRS inputs
Your converters 1/4” jacks let you connect balanced analog audio via TRS connectors.
TRSstands for Tip, Ring, Sleeve which refers to the three contacts of the jack connector.
The illustration in this section displays the wiring pins inside the male 1/4” jack connector
ifyouwant to make your own cables.
Sleeve (Ground) Tip (+) Sleeve (Ground) Ring (–) Tip (+)
Ring (–)
The illustration shows the jack connector’s positive, negative and ground wiring pins. If you
need to reverse the polarity of your analog audio cable to suit your audio equipment, you can
simply swap the positive and negative wiring on the tip and ring pins.
NOTE Microphone phantom power is supported on all inputs. To learn more about
setting phantom power as well as mic and line inputs, refer to the ‘changing settings
using switches’ section in thismanual.
6Getting Started
Connecting to an ATEM Switcher
Your ATEM Microphone Converter supports digital audio with the MADI protocol, also
known as Multichannel Audio Digital Interface. MADI is popular with most professional audio
manufacturers, broadcasters and high end recording facilities. These MADI ports have robust
BNC connectors and transmit audio data over 75 ohm coaxial cables up to 100 meters long.
Connect your converter’s MADI BNC output to the MADI input on your ATEM switcher.
ATEMswitcher models that support MADI include ATEM 4 M/E Constellation HD,
ATEMConstellation 8K and ATEM Television Studio HD8 ISO. The MADI input LED will
illuminatered when powered and white once MADI is detected.
CH 1 CH 2
PUSH PUSH
USE ONLY WITH A 250V FUSE
USB REMOTE TALKBACK
B
USB A
12-30V 6A
REF OUT TIMECODE OUT
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
REF IN TIMECODE IN
MADI OUT
MADI IN
AUX 1 PROGRAM
AUX 2 MULTIVIEW MULTIVIEW CONTROL OUT STUDIO OUT STEREO INETHERNET SDI INPUTS ANALOG AUDIO IN TALKBACK
SDI OUTPUTS
L L
R R R
LPUSH
ATEM Television Studio HD8
MADI OUT to MADI IN
You can find more information about controlling audio levels and enhancing the quality
ofyouraudio in the manual for your ATEM switcher.
Connecting a Monitor
Connect an HDMI television or monitor into the converter’s HDMI output.
Monitor Out
This video output lets you view the levels of each channel, plus a continuously updating
waveform showing audio peaks over a 60 second duration. You can also visually confirm
thatphantom power is activated and if inputs are set to mic or line level audio.
For more details about the monitor output and all the information it displays, refer to the
‘using the monitor output’ section.
7Getting Started
Settings
You can adjust different settings for ATEM Microphone Converter using the Blackmagic
Converters Setup utility and via the small switches on the side of your converter.
Adjust settings using the Blackmagic Converters Setup utility and the switches on the side of your converter
Blackmagic Converters Setup
Blackmagic Converters Setup is a software utility used to change settings and
update the internal software in your ATEM Microphone Converter.
First, download and install the latest Blackmagic Converters software from the
Blackmagic Design support center at www.blackmagicdesign.com/support
To use Blackmagic Converters Setup:
1 Connect ATEM Microphone Converter to your computer via USB.
2 Launch Converters Setup. Your converter model will be named in the utility home page.
3 Click on the circular ‘setup’ icon or the image of your ATEM Microphone Converter to open
the audio settings.
8Settings
Audio Settings
Input Labels
Customize the name and color of each input. This helps visually identify the inputs when using
the HDMI monitor output.
A quick example would be to name each source, then set all mic level sources to red and line
level sources to blue.
Label your inputs and select their display color using the menu
Indicators to the right of each color selection menu will display the input type and
whether phantom power is selected. These settings are selected via the switches
on the side of the converter. Information on setting the switches is provided later
inthis manual.
9Settings
Digital Preamps
Adjust the gain for each input using the digital preamp slider controls up to a maximum of +30dB.
Adjust the gain using the sliders
Different microphone types and brands can vary widely in analog audio levels, so the digital
preamplifiers allow compensation for the specific brand of microphone you use. The digital
preamplifier is processed using internal 32 bit RAW audio bit depth and that is much greater
precision than the MADI audio standard can support. This results in an extremely clean and
noise free gain stage.
The HDMI output enables you to measure the changes made to the audio waveform and meter
levels as you adjust the preamplifier sliders. The ATEMs internal mixer can then be used to
finesse these levels into the final mix.
Setup Settings
Setup settings let you change the name of your microphone converter, change network
settingsand displays the current version of your microphone converter’s internal software.
10Settings
Name
This name is helpful to identify the unit when more than one ATEM Microphone Converter is
connected to your computer or network.
Identify Converter
Clicking the checkbox activates the flashing green LEDs on each end of the converter. This
helps identify which converter you are currently adjusting using Blackmagic Converters Setup.
Network
ATEM Microphone Converter can connect to the network using a static IP address or by using
DHCP allowing you to change the audio settings and update the unit over a network.
Protocol
DHCP and static IP settings let you determine how your converter is connected to your network.
DHCP ATEM Microphone Converters are set to DHCP by default. The dynamic host
configuration protocol, or DHCP, is a service on network servers that automatically
finds your ATEM Microphone Converter and assigns an IP address. DHCP is a great
service that makes it easy to connect equipment via Ethernet and ensure their IP
addresses do not conflict with each other. Most computers andnetwork switchers
support DHCP.
Static IP When ‘static IP’ is selected, you can enter your network details manually. When
setting IP addresses manually so all units can communicate, they must share the
same subnet mask and gateway settings.
When using static IP and there are other devices on the network that have the same identifying
number in their IP address, there will be a conflict and the units won’t connect. If you encounter
a conflict, simply change the identifying number in the unit’s IP address.
For example, if the conflicting address is 192.100.40.30 change the last number field to anything
other than 30. If the new number is also being used, keep changing it until you find a unique
number that isn’t being used by other equipment.
Allow utility administration
Enabling the ‘via USB’ setting limits setting changes to only the computer connected via USB.
This removes the risk of anyone on the network making accidental settings changes.
11Settings
Updating Blackmagic Converters Setup utility
The first step is to download the Blackmagic Converters Setup utility from the Blackmagic
Design support center at www.blackmagicdesign.com/support
To update the software:
1 Run the Blackmagic Converters Setup installer on your computer and follow the onscreen
instructions.
2 After installation is complete, connect your ATEM Microphone Converter to the computer
viathe USB port on the rear panel. You can also connect to your network via Ethernet.
3 Launch Blackmagic Converters Setup and follow any onscreen prompt to update the
internal software. If no prompt appears, the internal software is up to date and there is
nothing further you need to do.
Changing Settings Using Switches
The side panel of the ATEM Microphone Converter features a set of small switches used to
select input type and turn phantom power on or off.
The switch legend printed on the base of the converter indicates which switches are to be
on/off for particular inputs. For example, if you have inputs 1 and 2 set to line and inputs 3 and 4
set to mic with phantom power, the switches will be set as shown in the following illustration.
LINE MIC
PHANTOM PWR
OFF
PHANTOM PWR
ON
PHANTOM PWR
OFF
PHANTOM PWR
ON
PHANTOM PWR
OFF
PHANTOM PWR
ON
PHANTOM PWR
OFF
PHANTOM PWR
ON
1
2
3
4
5
6
7
8
ATEM
Microphone Converter
LINE MIC
LINE MIC
LINE MIC
INPUT 3
INPUT 4
INPUT 2
INPUT 1
1 2 3 4 5 6 7 8
Inputs 1 and 2 set to line level
NOTE Phantom power is disabled when line level is selected.
12Settings
Using the Monitor Output
The monitor output is a fast way to visually check your audio inputs. At a glance, you can see
realtime waveforms of the previous 60 seconds, VU level meters plus indicators for phantom
power and mic or line level audio.
Waveforms
The realtime waveforms on the HDMI monitor output display up to the last 60 seconds of audio
starting from the right hand side. The color of the waveform can be changed via the Converters
Setup utility.
Elapsed time can be seen via the scale at the bottom of the output
Input ID
Each channel displays the input number. When connecting 2 or more converters
together, the numbers will continue from 5 onwards as each converter is connected
up to a maximum of 16 inputs per HDMI output. Asadditional converters are
connected, the input will increase sequentially soyou always know which
input is which.
Label
If the input has been labelled using the Blackmagic Converters Setup utility,
thelabelswill appear above each waveform.
13Using the Monitor Output
Level Type
Icons to the left of the waveform will display the current level type set using the switches
ontheside of your converter.
LINE
Line Level
MIC
Mic Level
+48
Phantom Power
Meters
Audio meters to the right of the waveform display the
VUlevel. Thesize of the VU meters on the HDMI output
will decrease as you connect more converters.
Connecting Additional Converters
Up to 4 ATEM Microphone Converters can be connected to the one HDMI output so you can
see all 16 channels at once. When connecting more than 4 converters together, connect a
monitor to the first of each additional bank of 4 ATEM Microphone converters so you can view
each additional microphone converter.
CH 1 CH 2
PUSH PUSH
USE ONLY WITH A 250V FUSE
USB REMOTE TALKBACK
B
USB A
12-30V 6A
REF OUT TIMECODE OUT
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
REF IN TIMECODE IN
MADI OUT
MADI IN
AUX 1 PROGRAM
AUX 2 MULTIVIEW MULTIVIEW CONTROL OUT STUDIO OUT STEREO INETHERNET SDI INPUTS ANALOG AUDIO IN TALKBACK
SDI OUTPUTS
L L
R R R
LPUSH
MADI OUT to MADI IN
MADI OUT to MADI IN
MADI 9-12 MADI 5-8 MADI 1-4MADI 13-16
MADI 29-32 MADI 25-28 MADI 21-24 MADI 17-20
MADI 17-32
MADI 1-16
This illustration shows 8 microphone converters daisy chained together to send 32 channels of audio via MADI
to ATEM Television Studio HD8
14Using the Monitor Output
Once you have 3 or more converters daisy chained together, the amount of room decreases.
This means some information will become hidden to make space for more inputs. You can
check mic/line level and phantom power settings using the setup utility or by checking the small
switches on the side of the unit.
HDMI monitor output when connecting 4 converters together
Each additional converter will populate the next four MADI channels so each input corresponds
to both the MADI input on your ATEM switcher and the input number on the HDMI monitor
output. The table below shows how the groups of audio inputs will populate on the ATEM
switcher’s audio mixer when daisy chaining multiple units.
ATEM Constellation 8K and ATEM 4 M/E Constellation model switchers
ATEM Television Studio model switchers
MADI Input 1-4 5-8 9-12 13-16 17-20 21-24 25-28 29-32 33-36 37-40 41-44 45-48 49-52 53-56 57-60 61-64
ATEM
Microphone
Converter
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
HDMI Display 1 HDMI Display 2 HDMI Display 3 HDMI Display 4
15Using the Monitor Output
Mounting ATEM Microphone Converter
Using the included mount plate you can fasten your ATEM Microphone Converter to a lectern,
desk, wall or other flat surface to keep it secure while still accessible to connect microphones.
1 With the ATEM Microphone Converter upside down, line up the pre drilled holes on the
mounting plate with the mounting points on the converter. There is enough clearance for
the rubber feet to remain attached but you can remove with a plastic edged scraping tool.
2 Using the supplied M3 5mm countersunk screws fasten the mounting plate to the converter.
3 Once the mounting plate is attached, you can now attach the converter using the 4 pre
drilled holes on the mounting plate to a lectern, desk, wall or other flat surface using self
tapping screws.
MOUNT PLATE
NOTE Only use the supplied M3 5mm countersunk screws to attach the mount plate to
the converter.
16Mounting ATEM Microphone Converter
Help
Getting Help
The fastest way to obtain help is to go to the Blackmagic Design online support pages and
check the latest support material available for your Blackmagic Converter.
Blackmagic Design Online Support Pages
The latest manual, software and support notes can be found at the Blackmagic Design support
center at www.blackmagicdesign.com/support.
Blackmagic Design Forum
The Blackmagic Design forum on our website is a helpful resource you can visit for
more information and creative ideas. This can also be a faster way of getting help
as there may already be answers you can find from other experienced users and
Blackmagic Design staff which will keep you moving forward. You can visit the forum at
https://forum.blackmagicdesign.com
Contacting Blackmagic Design Support
If you can’t find the help you need in our support material, or on the forum, please click the
“Send us an email” button on the support page to email a support request. Alternatively,
clickon the “Find your local support team” button and call your nearest Blackmagic Design
support office.
Checking the Software Version Currently Installed
To check which version of Blackmagic Converters Setup software is installed on your computer,
open the About Blackmagic Converters Setup window.
On Mac OS, open Blackmagic Converters Setup from the Applications folder. Select About
Blackmagic Converters Setup from the application menu to reveal the version number.
On Windows, open Blackmagic Converters Setup from your Start menu. Click on the Help
menu and select About Blackmagic Converters Setup to reveal the version number.
How to Get the Latest Software Updates
After checking the version of Blackmagic Converters Setup software installed on your computer,
please visit the Blackmagic Design support center at www.blackmagicdesign.com/support to
check for the latest updates. While it is usually a good idea to run the latest updates, it is wise to
avoid updating any software if you are in the middle of an important project.
17Help
Regulatory Notices
Disposal of Waste of Electrical and Electronic Equipment Within the European Union.
The symbol on the product indicates that this equipment must not be disposed of with other
waste materials. In order to dispose of your waste equipment, it must be handed over to a
designated collection point for recycling. The separate collection and recycling of your waste
equipment at the time of disposal will help conserve natural resources and ensure that it is
recycled in a manner that protects human health and theenvironment. Formore information
about where you can drop off your waste equipment for recycling, please contact your local
city recycling office or the dealer from whom you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digitaldevice,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated inacommercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, maycause harmful interference
to radio communications. Operation of this product in aresidential area is likely to cause
harmful interference, in which case the user will be required to correct the interference at
personal expense.
Operation is subject to the following two conditions:
1 This device may not cause harmful interference.
2 This device must accept any interference received, including interference that maycause
undesired operation.
Connection to HDMI interfaces must be made with high quality shielded HDMI cables.
R-R-BMD-20221125001
ISED Canada Statement
This device complies with Canadianstandards for Class A digital apparatus.
Any modifications or use of this product outside its intended use could void compliance to
these standards.
Connection to HDMI interfaces must be made with high quality shielded HDMI cables.
This equipment has been tested for compliance with the intended use in a
commercial environment. If the equipment is used in a domestic environment,
it may cause radio interference.
18Regulatory Notices
Safety Information
This equipment is suitable for use in tropical locations with an ambient temperature of
up to 40ºC.
Use only at altitudes not more than 2000m above sea level.
No operator serviceable parts inside. Refer servicing to your local Blackmagic Design
service centre.
State of California statement
This product can expose you to chemicals such as trace amounts of polybrominated biphenyls
within plastic parts, which is known to the state of California to cause cancer and birth defects
or other reproductive harm.
Formore information go to www.P65Warnings.ca.gov.
Singapore Notice
The power adapter supplied with your Blackmagic Design equipment has interchangeable
plugs to suit the mains socket outlets in a number of countries. Each plug marked with the
model numbers APD2-UK or APD2-EU are approved and suitable for use in Singapore.
19Safety Information
Warranty
12 Month Limited Warranty
Blackmagic Design warrants that this product will be free from defects in materials and workmanship
for a period of 12 months from the date of purchase. If a product proves to be defective during this
warranty period, Blackmagic Design, at its option, either will repair the defective product without
charge for parts and labor, or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, you the Customer, must notify Blackmagic Design
of the defect before the expiration of the warranty period and make suitable arrangements for
the performance of service. The Customer shall be responsible for packaging and shipping the
defective product to a designated service center nominated by Blackmagic Design, with shipping
charges pre paid. Customer shall be responsible for paying all shipping charges, insurance, duties,
taxes, and any other charges for products returned to us for any reason.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper
or inadequate maintenance and care. Blackmagic Design shall not be obligated to furnish service
under this warranty: a) to repair damage resulting from attempts by personnel other than Blackmagic
Design representatives to install, repair or service the product, b) to repair damage resulting from
improper use or connection to incompatible equipment, c) to repair any damage or malfunction
caused by the use of non Blackmagic Design parts or supplies, or d) to service a product that
has been modified or integrated with other products when the effect of such a modification or
integration increases the time or difficulty of servicing the product. THIS WARRANTY IS GIVEN BY
BLACKMAGIC DESIGN IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. BLACKMAGIC
DESIGN AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. BLACKMAGIC DESIGN’S RESPONSIBILITY TO REPAIR
OR REPLACE DEFECTIVE PRODUCTS IS THE WHOLE AND EXCLUSIVE REMEDY PROVIDED TO
THE CUSTOMER FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
IRRESPECTIVE OF WHETHER BLACKMAGIC DESIGN OR THE VENDOR HAS ADVANCE NOTICE
OF THE POSSIBILITY OF SUCH DAMAGES. BLACKMAGIC DESIGN IS NOT LIABLE FOR ANY
ILLEGAL USE OF EQUIPMENT BY CUSTOMER. BLACKMAGIC IS NOT LIABLE FOR ANY DAMAGES
RESULTING FROM USE OF THIS PRODUCT. USER OPERATES THIS PRODUCT AT OWN RISK.
© Copyright 2023 Blackmagic Design. All rights reserved. ‘Blackmagic Design’, ‘DeckLink’, ‘HDLink, ‘Workgroup Videohub’,
‘Multibridge Pro’, ‘Multibridge Extreme’, ‘Intensity’ and ‘Leading the creative video revolution’ are registered trademarks in the
US and other countries. All other company and product names may be trade marks of their respective companies with which
they are associated.
Thunderbolt and the Thunderbolt logo are trademarks of Intel Corporation in the U.S. and/or other countries.
20Warranty
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248

Blackmagic ATEM Microphone Converter Kullanım kılavuzu

Tip
Kullanım kılavuzu