Hikoki AW130 Kullanım kılavuzu

AW 130

High Pressure Washer

Hochdruckreiniger

Nettoyeur haute pression

Idropulitrice ad alta pressione

Hogedrukreiniger

Arandela de alta presión

Anilha de alta pressão

Myjka wysokociśnieniowa

Magasnyomású mosó

Basinçli yikama makinesi

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

Instrukcja obsługi

Kezelési utasítás

Kullanım talimatları

Do not use the appliance without reading the handling instruction.

Benutzen Sie das Gerät nicht, ohne die Gebrauchsanleitung gelesen zu haben.

N'utilisez pas l'appareil avant d’avoir lu les instructions d’utilisation.

Non utilizzare l’apparecchio senza aver letto le istruzioni per l’uso.

Gebruik dit toestel niet voordat u de gebruiksaanwijzing hebt gelezen.

No utilice el aparato sin leer las instrucciones de manejo.

Não utilize o aparelho sem ler as instruções de utilização.

Nie wolno używać urządzenia przed przeczytaniem instrukcji obsługi.

Csak a kezelési utasítás elolvasása után használja a készüléket.

Aygıtı kullanım talimatını okumadan kullanmayın.

123

456

78

91011

2

1

0

1

23

1

2

3

12 13 14

15 16 17

18 19 20

21 22 23

3

1

0

1

2

c

x

24 25 26

4

5

English Deutsch Français Italiano

14 to 15 mm 14 bis 15 mm 14 à 15 mm 14 - 15 mm

20 mm or less 20 mm oder weniger 20 mm au maximum 20 mm o meno

Cord holder Kabelhalter Enrouleur de câble Supporto del cavo

Washer protrusion Reinigervorsprung Saillie du nettoyeur Sporgenza

dell'idropulitrice

Handle Griﬀ Poignée Impugnatura

Screw Schraube Vis Vite

Power plug Netzstecker Fiche d'alimentation Spina di alimentazione

Water feed inlet Wasserzulauföﬀ nung Entrée d'alimentation en

eau Ingresso di alimentazione

dell'acqua

Water feed inlet cap Kappe für

Wasserzulauföﬀ nung Bouchon de l'alimentation

en eau Tappo dell'ingresso di

alimentazione dell'acqua

Water feed connector Wasserzulaufanschluss Connecteur d'alimentation

en eau Connettore di

alimentazione dell'acqua

Water outlet Wasserauslass Sortie d’eau Uscita dell'acqua

Water outlet cap Wasserauslasskappe Bouchon de la sortie d’eau Tappo dell’uscita

dell'acqua

O-ring O-Ring Joint torique O-ring

Ring Ring Joint Anello

Tighten Festziehen Serrez Serrare

Trigger gun Auslöserpistole Pistolet à gâchette Pistola a grilletto

Connector Anschluss Connecteur Connettore

Nozzle Düse Buse Ugello

Protrusion Vorsprung Saillie Sporgenza

Spray Sprühen Vaporisateur Spruzzo

Jet Strahl Jet Getto

Detergent nozzle Reinigungsmitteldüse Buse de détergent Ugello del detergente

Water supply pipe Wasserversorgungsrohr Conduite d'alimentation

en eau Tubo di alimentazione

acqua

Bottle Flasche Flacon Flacone

Suction hose Ansaugschlauch Tuyau d'aspiration Tubo ﬂ essibile di

aspirazione

Hose band Schlauchklemme Collier de serrage du

tuyau Fascetta fermatubo

Moisten the inside with

water Die Innenseite mit Wasser

befeuchten Humidiﬁ ez l'intérieur à

l'eau Inumidire l'interno con

acqua

Strainer Siebﬁ lter Crépine Filtro

Slotted screwdriver Schlitzschraubenzieher Tournevis pour écrous à

fente Cacciavite a lama piatta

One-touch joint Gelenk auf Knopfdruck Raccord rapide Raccordo rapido

Insert the suction hose Den Ansaugschlauch

einschieben Insérez le tuyau

d'aspiration Inserire il tubo ﬂ essibile di

aspirazione

Pass it through the ring

ﬁ rst Zuerst durch den Ring

führen Commencez par le passer

dans le joint Inserirlo prima nell'anello

Hose end Schlauchende Extrémité du tuyau Estremità tubo ﬂ essibile

Insert it past this point Über diesen Punkt hinaus

einschieben Insérez au-delà de ce

point Inserirlo oltre questo

punto

Accumulated water Angesammeltes Wasser Réservoir d'eau Acqua accumulata

High-pressure hose Hochdruckschlauch Tuyau à haute pression Tubo ﬂ essibile ad alta

pressione

Switch Schalter Interrupteur Interruttore

Trigger Auslöser Gâchette Grilletto

Center of the trigger Mitte des Auslösers Centre de la gâchette Centro del grilletto

Push Schieben Pousser Premere

6

English Deutsch Français Italiano

Trigger stopper Auslöserstopper Sécurité de la gâchette Fermo del grilletto

Lock Verriegeln Verrou Blocco

Release Entriegeln Relâchez Rilascio

Loosen Lockern Desserrez Allentare

Nozzle cleaner pin Düsenreinigungsstift Broche de nettoyage de

la buse Pulitore dell'ugello

Hole of the nozzle Düsenöﬀ nung Oriﬁ ce de la buse Foro dell’ugello

Variable nozzle Variable Düse Buse variable Ugello variabile

Turbo nozzle Turbodüse Buse turbo Ugello turbo

Detergent bottle nozzle Düse der

Reinigungsmittelﬂ asche Buse du ﬂ acon de

détergent Ugello del ﬂ acone del

detergente

7

Nederlands Español Português Polski

14 tot 15 mm de 14 a 15 mm 14 a 15 mm 14 do 15 mm

20 mm of minder 20 mm o menos 20 mm ou menos 20 mm lub mniej

Snoerhouder Soporte del cable Suporte do cabo Uchwyt przewodu

Uitsteeksel

hogedrukreiniger Saliente de la máquina de

limpieza Saliência do dispositivo Występ myjki

Hendel Empuñadura Pega Uchwyt

Schroef Tornillo Parafuso Wkręt

Stekker Enchufe Ficha de alimentação Wtyczka zasilania

Invoer watertoevoer Entrada de alimentación

de agua Entrada de alimentação

de água Wlot zasilania wodą

Dop invoer watertoevoer Tapa de entrada de

alimentación de agua Tampa da entrada de

alimentação de água Pokrywa wlotu zasilania

wodą

Aansluiting watertoevoer Conector de alimentación

de agua Conector de alimentação

de água Złącze zasilania wodą

Waterafvoer Salida de agua Saída de água Wylot wody

Dop waterafvoer Tapa de salida de agua Tampa da saída de água Pokrywa wylotu wody

O-ring Junta tórica O-ring Pierścień O-Ring

Ring Anilla Anel Pierścień

Vastzetten Apretar Apertar Dokręcić

Pistool met trekker Pistola de gatillo Pistola Pistolet

Aansluiting Conector Conector Złącze

Sproeier Boquilla Bocal Dysza

Uitsteeksel Saliente Saliência Występ

Sproeien Rociado Pulverização Natrysk

Straal Chorro Jato Strumień

Sproeier voor

reinigingsmiddel Boquilla de detergente Bocal de detergente Dysza detergentu

Watertoevoerbuis Tubería de alimentación

de agua Tubo de alimentação de

água Przewód zasilania wodą

Fles

Bote Garrafa Butelka

Aanzuigslang

Manguera de aspiración Mangueira de aspiração Wąż ssący

Slangklem Abrazadera de la

manguera Banda da mangueira Opaska węża

Maak de binnenkant nat

met water Humedezca la parte

interior con agua Humedecer o interior com

água Zwilżyć wnętrze wodą

Filter Filtro Filtro Filtr siatkowy

Sleufschroevendraaier Destornillador plano Chave de fenda Wkrętak płaski

Snelkoppeling Junta de un toque Junta de um toque Szybkozłącze

Aanzuigslang inschuiven Introduzca la manguera

de aspiración Insira a mangueira de

aspiração Włożyć wąż ssący

Eerst door de ring steken Pásela primero por la

anilla Passar primeiro pelo anel Najpierw przeprowadzić

go przez pierścień

Slanguiteinde Extremo de manguera Extremidade da

mangueira Koniec węża

Inschuiven tot voorbij dit

punt Introdúzcalo pasado este

punto Inserir para além deste

ponto Wsunąć go za ten punkt

Verzameld water Agua acumulada Água acumulada Nagromadzona woda

Hogedrukslang Manguera de alta presión Mangueira de alta

pressão Wąż wysokiego ciśnienia

Schakelaar Interruptor Interruptor Przełącznik

Trekker Gatillo Gatilho Spust

Midden van de trekker Centro del gatillo Centro do gatilho Środek spustu

Drukken Presionar Pressionar Przycisk

8

Nederlands Español Português Polski

Trekkerstop Tope del gatillo Batente do gatilho Ogranicznik spustu

Vergrendelen Bloquear Bloqueio Blokada

Ontgrendelen Soltar Soltar Zwolnienie

Loszetten Soltar Desapertar Poluzować

Reinigingspen voor

sproeier Clavija de limpieza de la

boquilla Pino de limpeza do bocal Kołek do czyszczenia

dyszy

Gat in de sproeier Oriﬁ cio de la boquilla Orifício do bocal Otwór dyszy

Variabele sproeier Boquilla variable Bocal variável Dysza regulowana

Turbosproeier Boquilla turbo Bocal turbo Dysza Turbo

Sproeier ﬂ es met

reinigingsmiddel Boquilla de bote de

detergente Bocal da garrafa de

detergente Dysza butelki z

detergentem

9

Magyar Türkçe

14 - 15 mm 14 ila 15 mm

20 mm vagy kevesebb 20 mm veya daha az

Kábel tartó Kablo tutucu

Mosó nyúlvány Yıkayıcı çıkıntısı

Markolat Tutamak

Csavar Vida

Tápfeszültség dugó Elektrik ﬁ şi

Vízellátó bemenet Su besleme girişi

Vízellátó bemenet

sapka Su besleme girişi

kapağı

Vízellátó csatlakozó Su besleme bağlantısı

Víz kimenet Su çıkışı

Víz kimenet sapka Su çıkışı kapağı

O-gyűrűHalka conta

RögzítőgyűrűHalka

Meghúzni Sıkın

Működtető pisztoly Tetikleme tabancası

Csatlakozó Bağlantı aparatı

Szórófej Ağızlık

Nyúlvány Çıkıntı

Permet Sprey

Sugár Püskürtme

Tisztítószer szórófej Deterjan ağızlığı

Vízellátó csőSu sağlama borusu

Tartály Şişe

Szívó tömlőEmiş hortumu

Tömlő bilincs Hortum bandı

Nedvesítse meg a

belsejét vízzel İç kısmı su ile

nemlendirin

SzűrőSüzgeç

Laposfejű csavarhúzó Düz tornavida

Gyorscsatlakozó Tek dokunuşlu mafsal

Illessze be a szívó

tömlőtEmiş borusunu

yerleştirin

Először vezesse át a

gyűrűnÖncelikle halkadan

geçirin

Tömlő vége Hortum ucu

Tolja túl ezen a ponton Bu noktadan geçirin

Összegyűlt víz Biriken su

Magasnyomású tömlőYüksek basınçlı hortum

Kapcsoló Sviç

Ravasz Tetik

A ravasz közepe Tetik merkezi

Nyomni İtin

Magyar Türkçe

Ravasz rögzítőTetik stoperi

Zár Kilit

Kioldó Serbest bırakma

Meglazítani Gevşetin

Szórófej tisztító tüske Ağızlık temizleme iğnesi

A szórófej nyílása Ağızlık deliği

Állítható szórófej Değişken ağızlık

Turbó szórófej Turbo ağızlık

Tisztítószer tartály

szórófej Deterjan şişesi ağızlığı

10

English Deutsch Français Italiano

Symbols

WARNING

The following show

symbols used for the

machine. Be sure that you

understand their meaning

before use.

Symbole

WARNUNG

Die folgenden Symbole

werden für diese Maschine

verwendet. Achten Sie

darauf, diese vor der

Verwendung zu verstehen.

Symboles

AVERTISSEMENT

Les symboles suivants

sont utilisés pour l’outil.

Bien se familiariser

avec leur signiﬁ cation

avant d’utiliser l’outil.

Simboli

AVVERTENZA

Di seguito mostriamo

i simboli usati per la

macchina. Assicurarsi

di comprenderne il

signiﬁ cato prima dell’uso.

To reduce the risk of

injury, user must read

instruction manual.

Failure to follow

the warnings and

instructions may result

in electric shock, ﬁ re

and/or serious injury.

Der Anwender muss die

Bedienungsanleitung

lesen, um das Risiko

einer Verletzung zu

verringern.

Wenn die Warnungen

und Anweisungen nicht

befolgt werden, kann es

zu Stromschlag, Brand

und/oder ernsthaften

Verletzungen kommen.

Pour réduire les risques

de blessures, l’utilisateur

doit lire le manuel

d’utilisation.

Tout manquement

à observer ces

avertissements et

instructions peut engendrer

des chocs électriques,

des incendies et/ou des

blessures graves.

Per ridurre il rischio

di lesioni, l’utente

deve leggere il

manuale delle

istruzioni.

La mancata osservanza

degli avvertimenti e

delle istruzioni potrebbe

essere causa di scosse

elettriche, incendi e/o

gravi lesioni.

Only for EU countries

Do not dispose of electric

tools together with

household waste material!

In observance of European

Directive 2012/19/EU

on waste electrical and

electronic equipment

and its implementation in

accordance with national

law, electric tools that

have reached the end of

their life must be collected

separately and returned

to an environmentally

compatible recycling facility.

Nur für EU-Länder

Werfen Sie

Elektrowerkzeuge nicht

in den Hausmüll!

Gemäss Europäischer

Richtlinie 2012/19/EU

über Elektro- und

Elektronik- Altgeräte

und Umsetzung in

nationales Recht

müssen verbrauchte

Elektrowerkzeuge

getrennt gesammelt und

einer umweltgerechaten

Wiederververtung

zugeführt werden.

Pour les pays européens

uniquement

Ne pas jeter les appareils

électriques dans les ordures

ménagères!

Conformément à la directive

européenne 2012/19/UE

relative aux déchets

d’équipements électriques

ou électroniques (DEEE),

et à sa transposition dans

la législation nationale,

les appareils électriques

doivent être collectés à

part et être soumis à un

recyclage respectueux de

l’environnement.

Solo per Paesi UE

Non gettare le

apparecchiature elettriche

tra i riﬁ uti domestici.

Secondo la Direttiva

Europea 2012/19/UE sui

riﬁ uti di apparecchiature

elettriche ed elettroniche

e la sua attuazione

in conformità alle

norme nazionali, le

apparecchiature elettriche

esauste devono essere

raccolte separatamente, al

ﬁ ne di essere reimpiegate in

modo eco-compatibile.

High-pressure water

can be dangerous if

used incorrectly. High-

pressure water jets

must not be directed

at people, electrical

equipment or the

washer itself.

Wasser unter hohem

Druck kann bei falscher

Benutzung gefährlich

sein. Der Hochdruckstrahl

darf nicht auf Menschen,

elektrische Anlagen,

oder den Reiniger selbst

gerichtet werden.

L'eau sous haute pression

peut être dangereuse

si elle n'est pas utilisée

correctement. Un jet

d'eau sous haute pression

ne doit pas être dirigé

vers des personnes, des

équipements électriques ou

le nettoyeur.

L'acqua ad alta pressione

può essere pericolosa,

se utilizzata in modo

scorretto. Non puntare il

getto ad alta pressione

dell'idropulitrice verso

persone, apparecchiature

elettriche o l'idropulitrice

stessa.

Water that has passed

through the backﬂ ow

valve cannot be used

for drinking.

Wasser, das durch

das Rückﬂ ussventil

geﬂ ossen ist, ist nicht

trinkbar.

L'eau qui est passée à

travers le clapet anti-

retour n'est pas potable.

L'acqua che ha

attraversato la valvola

antiriﬂ usso non è

potabile.

Alternating current Wechselstrom Courant alternatif Corrente alternata

Class II tool Werkzeug der Klasse II Outil classe II Attrezzo di Classe II

Warning Warnung Avertissement Avvertenza

VVolts Volt Volts Volt

AAmperes Ampere Ampères Ampere

Hz Hertz Hertz Hertz Hertz

WWatts Watt Watts Watt

kg Kilograms Kilogramm Kilogrammes Kilogrammi

MPa Megapascals Megapascal Mégapascals Megapascal

11

Nederlands Español Português Polski

Symbolen

WAARSCHUWING

Hieronder vindt u de symbolen

die voor dit toestel worden

gebruikt. Zorg ervoor dat u de

betekenis van de symbolen

begrijpt voordat u het toestel

begint te gebruiken.

Símbolos

ADVERTENCIA

A continuación se

muestran los símbolos

usados para la máquina.

Asegúrese de comprender

su signiﬁ cado antes del

uso.

Símbolos

AVISO

A seguir aparecem os

símbolos utilizados pela

máquina. Assimile bem

seus signiﬁ cados antes

do uso.

Symbole

OSTRZEŻENIE

Następujące oznaczenia

to symbole używane w

instrukcji obsługi maszyny.

Upewnij się, że rozumiesz

ich znaczenie zanim

użyjesz narzędzia.

Om het risico op

verwondingen te

verminderen, moet

de gebruiker de

instructiehandleiding lezen.

Als u geen rekening houdt met

de waarschuwingen en met de

instructies, stelt u zichzelf bloot

aan allerlei gevaren, zoals

elektrische schokken, brand

en/of ernstige blessures.

Para reducir el riesgo

de lesiones, el usuario

deberá leer el manual

de instrucciones.

Si no se siguen

las advertencias e

instrucciones, podría

producirse una

descarga eléctrica,

un incendio y/o daños

graves.

Para reduzir o risco

de lesão, o utilizador

deve ler o manual de

instruções.

Se não seguir todas

as instruções e os

avisos, pode provocar

um choque eléctrico,

incêndio e/ou

ferimentos graves.

Aby zmniejszyć ryzyko

odniesienia obrażeń,

użytkownik powinien

przeczytać instrukcję obsługi.

Nieprzestrzeganie

ostrzeżeń oraz wskazówek

bezpieczeństwa może

spowodować porażenie

prądem elektrycznym, pożar

i/lub odniesienie poważnych

obrażeń.

Alleen voor lidstaten van de EU

Verwijder elektrische

gereedschappen niet samen

met huishoudelijk afval. In

overeenstemming met de

Europese Richtlijn 2012/19/EU

betreﬀ ende afgedankte

elektrische en elektronische

apparatuur en de omzetting

van deze richtlijn in nationale

wetgeving moeten elektrische

gereedschappen na aﬂ oop

van hun nuttige levensduur

afzonderlijk worden opgehaald

en naar een milieuvriendelijk

recyclagebedrijf worden

gebracht.

Sólo para países de la Unión

Europea

¡No deseche los aparatos

eléctricos junto con los residuos

domésticos!

De conformidad con la Directiva

Europea 2012/19/UE

sobre residuos de aparatos

eléctricos y electrónicos y su

aplicación de acuerdo con

la legislación nacional, las

herramientas eléctricas cuya

vida útil haya llegado a su ﬁ n se

deberán recoger por separado

y trasladar a una planta de

reciclaje que cumpla con las

exigencias ecológicas.

Apenas para países da UE

Não deixe ferramentas

eléctricas no lixo

doméstico!

De acordo com a directiva

europeia 2012/19/UE

sobre ferramentas

eléctricas e electrónicas

usadas e a transposição

para as leis nacionais, as

ferramentas eléctricas

usadas devem ser

recolhidas em separado

e encaminhadas a uma

instalação de reciclagem

dos materiais ecológica.

Dotyczy tylko państw UE

Nie wyrzucaj

elektronarzędzi wraz z

odpadami z gospodarstwa

domowego!

Zgodnie z Europejską

Dyrektywą 2012/19/UE w

sprawie zużytego sprzętu

elektrotechnicznego i

elektronicznego oraz

dostosowaniem jej

do prawa krajowego,

zużyte elektronarzędzia

należy posegregować

i zutylizować w sposób

przyjazny dla środowiska.

Water onder hoge druk kan

gevaarlijk zijn als het niet op de

juiste manier wordt gebruikt.

Waterstralen onder hoge

druk mogen niet op mensen,

elektrische apparatuur of de

hogedrukreiniger zelf worden

gericht.

El agua a alta presión

puede ser peligrosa si se

utiliza incorrectamente.

Los chorros de agua a alta

presión no deben dirigirse

hacia las personas, el

equipo eléctrico o la misma

máquina de limpieza.

A água a alta pressão

pode ser perigosa quando

utilizada incorretamente. Os

jatos de água a alta pressão

não devem ser direcionados

para pessoas, equipamento

elétrico ou o próprio

dispositivo.

Woda pod wysokim ciśnieniem

może być niebezpieczna,

jeżeli jest nieprawidłowo

wykorzystywana. Strumienia

wody pod wysokim ciśnieniem

nie wolno kierować na ludzi,

urządzenia elektryczne lub

samą myjkę.

Water dat doorheen de

terugslagklep geleid is,

mag niet als drinkwater

worden gebruikt.

El agua que ha

pasado por la válvula

antirretorno no puede

utilizarse para beber.

A água que passe pela

válvula de reﬂ uxo não

pode ser utilizada para

beber.

Wody, która przeszła

przez zawór zwrotny nie

wolno wykorzystywać

do picia.

Wisselstroom Corriente alterna Corrente alternada Prąd przemienny

Gereedschap van

Klasse II Herramienta de Clase II Feramenta de classe II Narzędzie klasy II

Waarschuwing Advertencia Aviso Ostrzeżenie

VVolt Voltios Volts Wolty

AAmpère Amperes Amperes Ampery

Hz Hertz Hertz o hercios Hertz Herce

WWatt Watts o vatios Watts Waty

kg Kilogram Kilogramos Quilogramas Kilogramy

MPa Megapascal Megapascales Megapascais Megapaskale

12

Magyar Türkçe

Jelölések

FIGYELEM

Az alábbiakban a géphez

alkalmazott jelölések

vannak felsorolva. A

gép használata előtt

feltétlenül ismerje meg

ezeket a jelöléseket.

Simgeler

DİKKAT

Aşağıda, bu alet için kullanılan

simgeler gösterilmiştir.

Aleti kullanmadan önce

bu simgelerin ne anlama

geldiğini anladığınızdan emin

olun.

A sérülések

kockázatának

csökkentése érdekében,

a használónak el kell

olvasnia a használati

útmutatót.

A ﬁ gyelmeztetések

és utasítások be nem

tartása áramütést, tüzet

és/vagy súlyos sérülést

eredményezhet.

Kullanıcı yaralanma

riskini azaltmak için

kullanım kılavuzunu

okumalıdır.

Uyarılara ve talimatlara

uyulmaması elektrik

çarpmasına, yangına

ve/ veya ciddi

yaralanmaya neden

olabilir.

Csak EU-országok

számára

Az elektromos

kéziszerszámokat

ne dobja a háztartási

szemétbe!

A használt villamos

és elektronikai

készülékekről szóló

2012/19/EU irányelv és

annak a nemzeti jogba

való átültetése szerint az

elhasznált elektromos

kéziszerszámokat

külön kell gyűjteni, és

környezetbarát módon

újra kell hasznosítani.

Sadece AB ülkeleri için

Elektrikli el aletlerini

evdeki çöp kutusuna

atmayınız!

Kullanılmış elektrikli

aletleri, elektrik ve

elektronikli eski cihazlar

hakkındaki 2012/19/AB

Avrupa yönergelerine

göre ve bu yönergeler

ulusal hukuk kurallarına

göre uyarlanarak, ayrı

olarak toplanmalı ve

çevre şartlarına uygun

bir şekilde tekrar

değerlendirmeye

gönderilmelidir.

A magasnyomású víz

veszélyes lehet, ha

helytelenül használja.

A magasnyomású

vízsugarat nem szabad

közvetlenül ember,

elektromos berendezés

vagy maga a mosó felé

irányítani.

Yüksek basınçlı su hatalı

kullanıldığında tehlike

arz edebilir. Yüksek

bacınçlı su püskürtme

işlemi insanlara,

elektrikli ekipmanlara

veya yıkayıcının

kendisi üzerine doğru

uygulanmamalıdır.

A visszafolyó szelepen

áthaladó víz nem iható. Ters akım vanasından

geçen su içme amaçlı

olarak kullanılamaz.

Váltóáram Alternatif akım

II. osztályú szerszám Sınıf II aracı

Figyelem Dikkat

VVolt Volt

AAmper Amper

Hz Hertz Hertz

WWatt Watt

kg Kilogramm Kilogram

MPa Megapascal Megapaskal

English

13

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric

shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

1. Make sure the work area is always kept neat and

tidy.

Failure to observe this may result in accidents.

2. Take the surrounding environment into

consideration when using the washer.

○ Make sure the work area is brightly lit.

○ Do not use the washer near ﬂ ammable liquid or gas.

3. Beware of electric shocks.

Do not touch anything that is earthed (grounded) when

using the High Pressure Washer. (For example, pipes,

heaters, microwave ovens, refrigerators, etc.)

4. Do not use the washer near children.

○ People other than the person using the washer must not

be allowed to touch the washer or the cord.

○ People other than the person using the washer must not

come near the work area.

5. Store the washer in a safe place when not in use.

Store the washer in a dry, high location or protected with

a lock out of the reach of children.

6. Do not use the washer in inappropriate ways.

○ Use the High Pressure Washer within the limits of its

capabilities to ensure safe and eﬃ cient results.

○ Do not use the washer for any purpose other than that for

which it was designed.

7. Wear safe clothing when using the washer.

Use safety boots, gloves, helmets with visors and

earplugs in accordance with necessity.

8. Use protective goggles and dust-protection masks

when using the washer.

There is a chance that splashes and dust may enter the

eyes and mouth when using the washer.

9. Do not handle the power cord roughly.

○ Do not carry the High Pressure Washer with only the

power cord or pull the plug from the socket while holding

the power cord.

○ Keep the power cord away from heat, oil and sharp

corners.

10. Make sure the item being cleaned is ﬁ rmly ﬁ xed in

place.

There are cases in which the power of the water pressure

will cause light objects to ﬂ y oﬀ . Do not use the washer on

light objects that cannot be ﬁ xed in place.

11. Maintain a proper stance when using the washer.

Make sure your feet are always placed ﬁ rmly on the

ground to maintain balance.

12. Pay close attention to maintaining the High Pressure

Washer.

○ Clean the washer regularly to ensure safe and eﬃ cient

use.

○ Refer to the instruction manual when replacing supplied

parts.

○ Regularly check the power cord and ask your dealer for

repairs in the event of it being damaged.

○ If using an extension cord, check it regularly and replace

it in the event of it being damaged.

○ Make sure the grip is always kept dry and clean, and do

not allow oil of grease to come into contact with it.

13. Switch oﬀ and unplug the High Pressure Washer in

the following situations:

○ When it is not in use and when it is being repaired.

○ When attaching or detaching supplied or purchased

parts.

○ In other situations in which risks seem apparent.

14. Always remove equipment used for adjustment

purposes.

Check to make sure that all equipment used for

adjustment purposes has been removed before switching

on the power.

15. Avoid accidentally switching on the power.

○ Make sure you do not accidentally switch on the power to

the washer when it is plugged in.

○ Check to make sure that the washer is switched oﬀ

before plugging it into the power supply.

16. Inadequate extension cords can be dangerous.

17. Pay attention at all times when using the washer.

○ Pay attention to the methods of use stipulated in the

instruction manual and the surrounding environment

when using the High Pressure Washer.

○ Do not use the washer when tired.

18. Only use speciﬁ ed accessories and attachments.

Using accessories and attachments other than those

speciﬁ ed in the instruction manual or in HiKOKI catalogs

may result in accidents or injuries and must be avoided at

all costs.

19. High Pressure Washer repairs to be performed only

by experts.

○ The High Pressure Washer conforms to all relevant

safety regulations and must not be modiﬁ ed.

○ All repairs must be requested to HiKOKI authorized

service centers. Attempting to carry out repairs without

the correct skills may result in accidents or injuries.

20. Do not use the machine if a supply cord or important

parts of the machine are damaged, e.g. safety

devices, high pressure hoses, trigger gun.

21. Use a power supply that conforms to the voltage

listed on the name plate.

Failure to observe this may result in the washer operating

at higher speeds than normal, leading to overheating

and the outbreak of smoke and ﬁ re, which may cause

damage or injuries.

22. Use an independent power socket with a rated value

of 15 A or more.

Sharing a power socket with other equipment may result

in the breaker shutting down.

23. Hold the trigger gun ﬁ rmly in both hands when

using the washer.

Failure to observe this may result in injury.

24. High-pressure water can be dangerous if used

incorrectly.

High-pressure water jets must not be directed at people,

animals, easily-broken items, electrical equipment or the

washer itself.

25. Do not use gasoline, oil, organic solvents or

other inﬂ ammable or toxic liquids, or any other

inappropriate liquid.

Failure to observe this may result in explosions, the

outbreak of ﬁ re or smoke, or other accidents, which may

cause damage or injury.

(Original instructions)

English

14

33. If the washer is accidently dropped or banged into

something solid, inspect it for damage, cracks and

malformation.

Failure to observe this may result in injury.

34. Do not direct the jet against yourself or others in

order to clean clothes or foot-wear.

35. Always switch oﬀ the mains disconnecting switch

when leaving the machine unattended.

CAUTION

1. Purge all of the pressure within the washer before

disconnecting the high-pressure hose.

2. Attach all supplied accessories correctly in

accordance with the instruction manual.

Failure to observe this may result in the accessories

becoming detached or in injury.

3. Check to make sure that no foreign matter is

adhering to the object being washed.

Failure to observe this may result in the matter ﬂ ying oﬀ

and causing unexpected injury.

4. Do not spray a jet of water at the areas surrounding

labels on the object being washed.

Failure to observe this may result in the labels peeling oﬀ .

5. Grip the handle ﬁ rmly when carrying the washer.

6. Do not use any accumulated water other than clean

water from the faucet (water containing dirt, mud,

sand, etc.) when using the auto-suction function.

7. Children should be supervised to ensure that they

don't play with the appliance.

26. When washing automobile tires, make sure that the

tip of the nozzle is kept at least 50cm distant from

the surface being washed.

Failure to observe this may result in damage to the tire or

brakes, which may cause serious accidents.

27. Do not touch the power plug or power socket with

wet hands.

Failure to observe this may result in electric shocks.

28. High pressure cleaners shall not be used by children

or untrained personnel.

29. Water that has ﬂ own through backﬂ ow preventers is

considered to be non-potable.

Make sure that a backﬂ ow valve is used without fail when

connecting the washer to a drinking water faucet.

Water that has passed through the backﬂ ow valve cannot

be used for drinking.

30. Make sure that water is not splashed onto the High

Pressure Washer, power cord, extension cable,

power plug, power socket or other areas. Also,

neither exposes it to rain nor use it in the rain.

Failure to observe this may result in electric shocks.

31. Do not hold the trigger gun when ﬁ xing it in place.

32. If the washer is not functioning normally or is

emitting strange noises or vibrations switch it oﬀ

immediately and contact HiKOKI authorized service

centers to request inspections or repairs.

Continued use may result in injury.

SPECIFICATIONS

Model AW130

Voltage (by areas)*1Single-phase AC 50/60 Hz

Voltage 220 V to 240 V

Power input*11600 W

Max. discharge pressure (1MPa: 10.2 kgf/cm2) 9.0 MPa

Max permissible pressure 13.0 MPa

Max feed pressure 0.7 MPa

Max water discharge 6.0 L/min

Permissible temperature 40 °C or less

Water feeding method Faucet connection type

Dimensions (Length × Width × Depth) 325 mm × 260 mm × 790 mm

(Including the handle, power cord holder and water feed connector)

Weight*28.3 kg

*1 Be sure to check the nameplate on product as it is subject to change by areas.

*2 Weight: Excluding the power cord, weight consists of trigger gun, high-pressure hose, variable nozzle, water feed connector

and accessory holder.

English

15

STANDARD ACCESSORIES

(1) Trigger gun ..................................................................1

(2) High-pressure hose (10 m) ..........................................1

(3) Variable nozzle ...........................................................1

(4) Turbo nozzle ...............................................................1

(5) Detergent bottle nozzle ...............................................1

(6) One-touch joint (black)

(For use with the strainer hose) ...................................1

(7) Water feed connector ..................................................1

(8) Nozzle cleaner pin .......................................................1

(9) Cord holder .................................................................1

(10)

Handle (with 4 attachment screws) .............................1

(1) (2)

(3) (4)

(5) (6)

(7) (8)

(9) (10)

English

16

OPTIONAL ACCESSORIES (sold separately)

Items shown in are sold separately. Contact HiKOKI authorized service centers for replacements if the standard

accessories become damaged or broken.

Variable nozzle

[Standard accessory]

Turbo nozzle

[Standard accessory]

Cleaning brush

Washes away dirt that has

been dislodged with the

brush.

Rotary brush

The central brush is rotated

by water pressure for cleaning

the windows and other items

with large surfaces.

Angle nozzle (variable)

Used for cleaning diﬃ cult-

to-reach places, such as

the underneath of cars and

ceilings, etc.

Pipe cleaning kit

(7.5 mm hose)

High-pressure water jets

from the front of the hose are

reversed to clean the inside

of the pipe.

Trigger gun

[Standard accessory]

High-pressure extension hose

(10 m)

Extends the length of the high-

pressure hose supplied.

High-pressure hose

[Standard accessory]

Water feed connector

[Standard accessory]

One-touch joint (black)

[Standard accessory]

Strainer hose set

Detergent bottle nozzle

[Standard accessory]

Accumulated water

English

17

APPLICATIONS

○ Cleans screen doors, window glass, ﬂ oors, walls, etc.

○ Cleans automobiles, motorbikes, etc.

○ Cleans mud oﬀ gardening equipment and agricultural

equipment.

PRIOR TO OPERATION

1. Installation of an earth leakage circuit breaker

It is recommended that an earth leakage circuit breaker

is connected to the washer to shut oﬀ the power if leaking

current exceeds 30 mA for 30 milliseconds in order to

prevent electric shocks.

2. Keep the work area neat and tidy

Dirty water will be sprayed about when using the washer.

It is therefore necessary to check the area to make sure

there are no hindrances, and keep the work area neat

and tidy.

3. Situating the washer

Select ﬂ at locations where the washer will not be

splashed with water when cleaning.

4. Using extension cords

Make sure the cord is thick enough to provide a constant

supply of electricity, and use cords that are as short as

possible.

Acceptable cord thicknesses (Nominal cross sectional

area cable) and cord length are indicated in the table

below.

Cord Thickness (mm2) Cord Length (m)

1 12.5

1.5 20

2.5 30

5. Prepare a water feed hose (Fig. 1)

Prepare the following when using water feed hoses:

○ Hoses that can withstand pressure (equipped with

meshes)

○ Hoses with an inner diameter of 14 to 15 mm.

○ Hoses with an outer diameter of 20 mm or less.

6. Attaching the cord holder (Fig. 2)

Align the groove on the cord holder with the protrusion on

the washer and insert it as far as it will go.

7. Attaching the handle (Fig. 3)

Use a Phillips screwdriver to ﬁ rmly tighten all four screws.

INSPECTIONS PRIOR TO USE

WARNING

Check the following before using the washer. Check the

items listed in 1 and 2 before plugging into the power

socket.

1. Check to make sure the switch is at the “OFF”

position (Fig. 4)

Plugging the washer into the power socket with the

switch set at “ON” will cause the washer to immediately

begin operating, which may result in unexpected injuries.

2. Check the power supply

Only use a rated voltage.

Do not use motor engines are direct current. Failure to

observe this will not only result in damage to the washer,

it is also very dangerous.

3. Check the power socket

If the power socket is loose or the plug is easily dislodged,

it needs to be repaired.

It is dangerous to use it in this condition. Consult with

your local electrical engineering outlet.

ATTACHING PARTS

Make sure all parts are correctly attached in the following

sequence in order to guarantee safe usage.

WARNING

Switch oﬀ the washer and disconnect it from the power

socket without fail to prevent unexpected accidents.

1. Attach the water feed connector to the water feed

inlet on the washer (Fig. 5)

Remove the cap on the washer’s water feed inlet and

ﬁ rmly attach the water feed connector.

Loose connections may result in water leaks.

2. Attaching the high-pressure hose to the washer’s

water outlet (Fig. 6)

Both ends of the high-pressure hose have the same

conﬁ guration, so either end may be connected.

Remove the water outlet cap from the washer, insert the

high-pressure hose into the water outlet and then rotate

the high-pressure hose ring to ﬁ x it in place.

NOTE

○ Moisten the O-ring with water if it is diﬃ cult to insert the

hose.

○ If it is not possible to tighten the ring, it means that the

high-pressure hose has not been inserted far enough.

3. Attach the high-pressure hose to the trigger gun.

(Fig. 7)

Grip the thick end of the high-pressure hose, insert it into

the connector on the trigger gun, and then rotate the ring

on the hose to ﬁ x it in place.

NOTE

○ Moisten the O-ring with water to facilitate the connection

if it is diﬃ cult to insert the hose.

○ If the ring cannot be tightened, it means that the end of

the high-pressure hose has not been suﬃ cient inserted.

4. Attach the nozzle to the trigger gun.

(1) Align the protrusion on the nozzle with the entry hole on

the trigger gun and press it into place.

NOTE

○ Remove all dirt, mud and other matter from the trigger

gun’s entry hole and the protrusion on the nozzle.

○ Moisten the O-ring with water to facilitate the connection

if it is diﬃ cult to insert the nozzle.

(2) Press down ﬁ rmly on the nozzle and then rotate it in the

direction of the arrow until it stops (half rotation.)

(3) Check to make sure that the nozzle cannot be pulled out

once it has been attached.

Press down ﬁ rmly on the nozzle and then rotate it counter-

clockwise until it stops. The nozzle can be withdrawn at

that position.

USING DIFFERENT NOZZLES

Variable nozzle (Fig. 10)

The variable nozzle can be used to alternation between

“Jet” and “Spray”.

Rotate the end on the nozzle clockwise for “Jet”, and

counter-clockwise for “Spray”.

• Jet washer

A water jet is discharged in a direct line to remove

stubborn mud and other dirt from agricultural machinery,

etc.

English

18

• Spray washer

The water is discharged in a wide fan for cleaning walls,

motorbikes and automobiles, etc.

The entire nozzle can be rotated by approximately 90

degrees to change the shape of the spray between

horizontal and vertical.

NOTE

○ Set the spray adjustment to “Jet” ﬁ rst of all, and then

gradually move it to the “Spray” position while pulling the

trigger.

Note that there is a chance of the water being sprayed

horizontally over a wide area if this is rotated fully to the

“Spray” position.

○ Note that the nozzle may be damaged if it is forced to

move past the stop position when alternating between

“Jet” and “Spray”.

Turbo nozzle

The turbo nozzle rotates as it sprays high-pressure jets of

water for eﬃ cient washing.

NOTE

The turbo nozzle only discharges powerful jets of water

when set at the “Jet” mode.

Avoid using this on items that are easily broken or for

which coatings are easily peeled.

Detergent bottle nozzle (Fig. 11 and 12)

Sprays water mixed with detergent.

Uses neutral detergents available on the open market.

(1) Insert the water feed pipe into the detergent nozzle.

(2) Pour an undiluted neutral detergent into the bottle and

then screw the bottle onto the detergent nozzle.

(3) Attaching and removing the detergent bottle nozzle is the

same as explained for other nozzles.

When inserting the detergent bottle, make sure that

the trigger gun is pointing in the direction shown in the

illustration on the right.

(4) Aim the detergent nozzle at the article to be washed and

pull the trigger on the trigger gun to spray a mixture of

water and detergent at low pressure.

WARNING

Do not use acidic or alkali detergents. Use only neutral

detergents available on the open market.

Using detergents other than neutral detergents or

chemical agents may result in accidents or malfunctions.

NOTE

Moisten the O-ring with water if it is diﬃ cult to insert the

nozzle.

USING THE STRAINER HOSE SET (sold

separately)

The separately-sold strainer hose set is equipped with a

function that will automatically suck water from a water tank,

etc., when attached to the AW130.

The maximum height of suction (lifting range) is

approximately 0.5 m.

Attach this correctly in accordance with conditions.

Suction height when the height of the water feed outlet is

lower than the maximum height of the suction hose: From

the maximum height of the suction hose to the surface of

the water.

Less than 50 cm

Water surface

Water

feed inlet

Maximum height of the

suction hose

Suction height when the height of the water feed outlet is

the same as the maximum height of the suction hose: From

the water feed outlet to the surface of the water.

Less than 50 cm

Water surface

Water feed inlet

(maximum height of

the suction hose)

1. Attaching the strainer to the suction hose (Fig. 13)

(1) Pass the suction hose through the hose band supplied

and then gently moisten the inside of the suction hose

with water.

(2) Insert the strainer as far as it will go, and then ﬁ rmly

tighten the hose band with a ﬂ at-headed screwdriver.

2. Attaching the one-touch joint (black) to the suction

hose (Fig. 14)

Attach the one-touch joint (black) supplied as a standard

accessory to the suction hose.

3. Starting the suction hose water suction process

(Fig. 15)

Sink the strainer hose set into a container ﬁ lled with

water.

Start oﬀ the suction process (introduce water to the

suction hose.)

NOTE

○ Do not use anything other than clean water (river or pond

water, muddy water containing sand granules.)

Failure to observe this may result in malfunctions.

○ Set the switch at “ON” without the nozzle attached.

Failure to observe this may result in dry operations,

leading to malfunctions.

4. Insert the one-touch joint into the water feed

connector (Fig. 16)

Withdraw the one-touch joint from the accumulated water

and insert it into the water feed connector on the washer

while making sure that the water inside the hose does not

escape.

English

19

5. Check to make sure the water is ﬂ owing out

(Fig. 17)

(1) Connect the trigger gun from which the nozzle has been

removed to the high-pressure hose.

(2) Plug in the power socket and set the switch to “ON”.

(3) Pull the trigger gun’s trigger, and then set the switch to

“OFF” after checking that suﬃ cient water is ﬂ owing out.

6. Attach the nozzle.

NOTE

Set the switch at “OFF” if water does not ﬂ ow out within

two minutes.

Failure to observe this may result in malfunctions (dry

operations.)

7. Washing

Set the switch at “ON” and pull the trigger gun’s trigger to

commence washing.

8. Cleaning

Remove all dirt from the strainer’s grill, wash it with water

and store it after it has dried.

WASHING

WARNING

○ Do not switch the washer on while the trigger is being

pulled.

Failure to observe this may result in high-pressure water

being sprayed immediately, leading to unexpected

accidents.

○ Do not point the nozzle at people or animals.

Failure to observe this may result in injury.

CAUTION

○ Set the switch to “OFF” immediately if the hose becomes

detached from the faucet or washer, and if water is no

longer being fed to the washer.

Failure to observe this may result in immediate

malfunctions (dry operations.)

○ Set the switch to “OFF” without fail when temporarily

suspending operations.

Failure to observe this may result in the motor

automatically starting up.

○ Place your ﬁ nger in the center of the trigger during

operations (Fig. 18)

Failure to observe this may result in injury from pinched

ﬁ ngers.

Grip the gun and nozzle ﬁ rmly with both hands.

○ The trigger gun may kick back when water is discharged.

NOTE

○ Do not use the water hose when it is wound onto the reel.

Failure to observe this may result in insuﬃ cient water

feed.

○ Commence initial washing approximately 2 to 3 meters

away from the targeted item, and then move gradually

closer while checking the level of cleaning until you reach

a distance in which soiling is eﬀ ectively washed away.

The pressure of the spray from the washer is

approximately 20-times greater than tap water. High-

pressure water jets may therefore damage or peel the

coating from the items being washed.

○ There are cases when the water spray will appear

unstable owing to the fact that air that has built up in

the pump and hose is purged together with the water

immediately after use. In this event, allow the water to

ﬂ ow out until it stabilizes.

○ Leave two or more seconds gap between pulling and

releasing the trigger.

Failure to observe this may result in the pressure switch

malfunctions.

○ Do not use the washer for more than thirty consecutive

minutes without giving it a break.

1. Open the faucet to its fullest.

Point the nozzle in a safe direction and then fully open the

faucet. Check to make sure no water is leaking from the

joints.

Release the trigger stopper with the washer switched oﬀ ,

pull the trigger on the trigger gun to discharge a small

amount of water from the nozzle with just the pressure

from the tap water. Check to make sure that no water is

leaking.

NOTE

Do not switch the washer on with the faucet turned oﬀ .

Failure to observe this may result in malfunctions.

2. Set the switch to the “ON” position (Fig. 19)

The motor will start operating when the washer is

switched on. The motor will automatically switch oﬀ once

suﬃ cient water pressure has built up inside the washer.

3. Pull the trigger (Fig. 20)

Hold the trigger gun ﬁ rmly in both hands, point the nozzle

at the item to be washed, and then pull the trigger.

The high-pressure water jet will spray out.

Adjust the nozzle between “Jet” and “Spray” in

accordance with need.

Trigger stopper (Fig. 21)

The trigger gun is ﬁ tted with a trigger stopper to prevent

the trigger from being pulled.

The trigger is locked and released by pressing the

stopper in the direction shown by the arrows.

NOTE

Lock the trigger with the trigger stopper during pauses

and after washing has been completed.

ON COMPLETION OF USE

Once the targeted item has been washed, drain the residual

water from the washer and store it in a well-ventilated

location to dry.

There are cases in which water left in the hose may freeze

during the winter, so drain as much water as possible and

store it indoors.

WARNING

Make sure all residual water is drained from the washer,

the trigger gun and the hose, etc., after use.

Failure to observe this may result in freezing, leading to

malfunctions.

1. Draining water from the washer

(1) Stop the water supply.

(2) Set the switch to “ON” and pull the trigger on the trigger

gun to drain the water from the inside of the washer.

Continue this until water is no longer discharged

(approximately 30 to 60 seconds.)

(3) Press the trigger stopper on the trigger gun to lock it in

place.

2. Set the switch to “OFF”.

(1) Switch oﬀ the washer.

(2) Unplug the power cord from the mains socket.

NOTE

Leaving the washer switched on may result in dry

operations, leading to malfunctions.

3. Removing the high-pressure hose (Fig. 22)

(1) Loosen the ring.

(2) Remove the high-pressure hose from the washer’s water

outlet.

(3) Drain all residual water from the high-pressure hose.

English

20

4. Drain the water from the washer (Fig. 23)

(1) Tilt the washer to drain out the residual water.

(2) Wipe away all moisture with a dry cloth.

CAUTION

Water left in the washer may freeze in the winter, which

could result in damage to the pump.

SAFETY MECHANISMS

The washer is equipped with the following safety mechanisms

to ensure safe usage.

Power switch

This prevents the washer from being unintentionally

operated.

Trigger gun equipped with a lock

This prevents the trigger from being pulled, unintentionally

operating the washer.

Pressure switch

This prevents the pressure inside the washer from

exceeding permissible levels. Releasing the lever on the

trigger gun causes the valve operated by water pressure

to halt pump operations, which allows the pressure to be

released through the water feed. The pump is started

again when the lever is pulled.

Thermal protector

This protects the motor by halting operations when

abnormal heat is detected in the motor. It will start

operating again when the motor cools down.

MAINTENANCE AND INSPECTION

WARNING

Switch oﬀ the washer and disconnect the plug from the

power socket without fail when inspecting and cleaning it.

1. Inspecting the washer and hoses (Fig. 24)

Check to make sure that there is no damage, cracks or

malformations.

Make sure you clean the hole on the nozzle with the

nozzle cleaner pin supplied on a regular basis.

NOTE

Detach the trigger gun and clean the nozzle hole.

2. Inspecting the strainer (Fig. 25)

Wash all blockages out of the grid with water on a regular

basis.

NOTE

Withdraw the strainer from the water feed inlet with the

use of ﬂ at radio pliers.

3. Clean the washer

Squeeze the excess moisture from a cloth soaked in

soap and water and wipe the washer.

Do not use gasoline, thinner, benzene, kerosene, etc.

Failure to observer this may result in malformations.

4. Check for loose screws.

Check for loose screws on a regular basis and tighten

any screws that are loose. Failure to observe this could

be dangerous.

5. Tidying up and storing the washer after use

(Fig. 26)

The accessories can be stored inside the washer as

shown in Fig. 26 when not in use and when being carried

around.

Avoid the following environments and store the washer

and accessories in a safe, dry location when not in use.

○ Do not store within the reach of children, or in locations

where children can use it.

○ Do not store in location where rain can reach it, such as in

front of the house, or in locations with high humidity.

○ Do not store in locations that are subject to drastic

changes in temperature or direct sunlight.

○ Do not store in locations containing volatile substances

that may ignite or explode.

6. Replacing supply cord

If the replacement of the supply cord is necessary, it has

to be done by a HiKOKI Authorized Service Center to

avoid a safety hazard.

7. Service parts list

CAUTION

Repair, modiﬁ cation and inspection of HiKOKI Power

Tools must be carried out by a HiKOKI Authorized

Service Center.

This Parts List will be helpful if presented with the tool to

the HiKOKI Authorized Service Center when requesting

repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

HiKOKI Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without prior

notice.

Sayfa yükleniyor ...

Hikoki AW130 Kullanım kılavuzu

Hikoki AW130 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler