Hikoki AW130 Kullanım kılavuzu

Tip
Kullanım kılavuzu
AW 130
High Pressure Washer
Hochdruckreiniger
Nettoyeur haute pression
Idropulitrice ad alta pressione
Hogedrukreiniger
Arandela de alta presión
Anilha de alta pressão
Myjka wysokociśnieniowa
Magasnyomású mosó
Basinçli yikama makinesi
Handling instructions
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
Instrucciones de manejo
Instruções de uso
Instrukcja obsługi
Kezelési utasítás
Kullanım talimatları
Do not use the appliance without reading the handling instruction.
Benutzen Sie das Gerät nicht, ohne die Gebrauchsanleitung gelesen zu haben.
N'utilisez pas l'appareil avant d’avoir lu les instructions d’utilisation.
Non utilizzare l’apparecchio senza aver letto le istruzioni per l’uso.
Gebruik dit toestel niet voordat u de gebruiksaanwijzing hebt gelezen.
No utilice el aparato sin leer las instrucciones de manejo.
Não utilize o aparelho sem ler as instrões de utilização.
Nie wolno używać urządzenia przed przeczytaniem instrukcji obsługi.
Csak a kezesi utasítás elolvasása un használja a késket.
Aygıtı kullanım talimatını okumadan kullanmayın.
123
456
78
91011
2
1
0
1
23
1
2
3
12 13 14
15 16 17
18 19 20
21 22 23
3
1
0
1
2
c
x
24 25 26
4
5
English Deutsch Français Italiano
14 to 15 mm 14 bis 15 mm 14 à 15 mm 14 - 15 mm
20 mm or less 20 mm oder weniger 20 mm au maximum 20 mm o meno
Cord holder Kabelhalter Enrouleur de câble Supporto del cavo
Washer protrusion Reinigervorsprung Saillie du nettoyeur Sporgenza
dell'idropulitrice
Handle Gri Poignée Impugnatura
Screw Schraube Vis Vite
Power plug Netzstecker Fiche d'alimentation Spina di alimentazione
Water feed inlet Wasserzulau nung Entrée d'alimentation en
eau Ingresso di alimentazione
dell'acqua
Water feed inlet cap Kappe für
Wasserzulau nung Bouchon de l'alimentation
en eau Tappo dell'ingresso di
alimentazione dell'acqua
Water feed connector Wasserzulaufanschluss Connecteur d'alimentation
en eau Connettore di
alimentazione dell'acqua
Water outlet Wasserauslass Sortie d’eau Uscita dell'acqua
Water outlet cap Wasserauslasskappe Bouchon de la sortie d’eau Tappo dell’uscita
dell'acqua
O-ring O-Ring Joint torique O-ring
Ring Ring Joint Anello
Tighten Festziehen Serrez Serrare
Trigger gun Ausserpistole Pistolet à gâchette Pistola a grilletto
Connector Anschluss Connecteur Connettore
Nozzle Düse Buse Ugello
Protrusion Vorsprung Saillie Sporgenza
Spray Sprühen Vaporisateur Spruzzo
Jet Strahl Jet Getto
Detergent nozzle Reinigungsmitteldüse Buse de détergent Ugello del detergente
Water supply pipe Wasserversorgungsrohr Conduite d'alimentation
en eau Tubo di alimentazione
acqua
Bottle Flasche Flacon Flacone
Suction hose Ansaugschlauch Tuyau d'aspiration Tubo essibile di
aspirazione
Hose band Schlauchklemme Collier de serrage du
tuyau Fascetta fermatubo
Moisten the inside with
water Die Innenseite mit Wasser
befeuchten Humidi ez l'intérieur à
l'eau Inumidire l'interno con
acqua
Strainer Sieb lter Crépine Filtro
Slotted screwdriver Schlitzschraubenzieher Tournevis pour écrous à
fente Cacciavite a lama piatta
One-touch joint Gelenk auf Knopfdruck Raccord rapide Raccordo rapido
Insert the suction hose Den Ansaugschlauch
einschieben Inrez le tuyau
d'aspiration Inserire il tubo essibile di
aspirazione
Pass it through the ring
rst Zuerst durch den Ring
führen Commencez par le passer
dans le joint Inserirlo prima nell'anello
Hose end Schlauchende Extrémité du tuyau Estremità tubo essibile
Insert it past this point Über diesen Punkt hinaus
einschieben Inrez au-delà de ce
point Inserirlo oltre questo
punto
Accumulated water Angesammeltes Wasser Réservoir d'eau Acqua accumulata
High-pressure hose Hochdruckschlauch Tuyau à haute pression Tubo essibile ad alta
pressione
Switch Schalter Interrupteur Interruttore
Trigger Auslöser Gâchette Grilletto
Center of the trigger Mitte des Auslösers Centre de la gâchette Centro del grilletto
Push Schieben Pousser Premere
6
English Deutsch Français Italiano
Trigger stopper Ausserstopper curité de la gâchette Fermo del grilletto
Lock Verriegeln Verrou Blocco
Release Entriegeln Relâchez Rilascio
Loosen Lockern Desserrez Allentare
Nozzle cleaner pin Düsenreinigungsstift Broche de nettoyage de
la buse Pulitore dell'ugello
Hole of the nozzle se nung Ori ce de la buse Foro dell’ugello
Variable nozzle Variable Düse Buse variable Ugello variabile
Turbo nozzle Turbodüse Buse turbo Ugello turbo
Detergent bottle nozzle se der
Reinigungsmittel asche Buse du acon de
détergent Ugello del acone del
detergente
7
Nederlands Español Português Polski
14 tot 15 mm de 14 a 15 mm 14 a 15 mm 14 do 15 mm
20 mm of minder 20 mm o menos 20 mm ou menos 20 mm lub mniej
Snoerhouder Soporte del cable Suporte do cabo Uchwyt przewodu
Uitsteeksel
hogedrukreiniger Saliente de la máquina de
limpieza Saliência do dispositivo Występ myjki
Hendel Empadura Pega Uchwyt
Schroef Tornillo Parafuso Wkręt
Stekker Enchufe Ficha de alimentação Wtyczka zasilania
Invoer watertoevoer Entrada de alimentación
de agua Entrada de alimentão
de água Wlot zasilania wodą
Dop invoer watertoevoer Tapa de entrada de
alimentación de agua Tampa da entrada de
alimentão de água Pokrywa wlotu zasilania
wodą
Aansluiting watertoevoer Conector de alimentación
de agua Conector de alimentação
de água Złącze zasilania wodą
Waterafvoer Salida de agua Saída de água Wylot wody
Dop waterafvoer Tapa de salida de agua Tampa da sda de água Pokrywa wylotu wody
O-ring Junta tórica O-ring Pierścień O-Ring
Ring Anilla Anel Pierścień
Vastzetten Apretar Apertar Dokręcić
Pistool met trekker Pistola de gatillo Pistola Pistolet
Aansluiting Conector Conector Złącze
Sproeier Boquilla Bocal Dysza
Uitsteeksel Saliente Saliência Występ
Sproeien Rociado Pulverização Natrysk
Straal Chorro Jato Strumień
Sproeier voor
reinigingsmiddel Boquilla de detergente Bocal de detergente Dysza detergentu
Watertoevoerbuis Tubería de alimentación
de agua Tubo de alimentação de
água Przewód zasilania wodą
Fles
Bote Garrafa Butelka
Aanzuigslang
Manguera de aspiración Mangueira de aspiração Wąż ssący
Slangklem Abrazadera de la
manguera Banda da mangueira Opaska węża
Maak de binnenkant nat
met water Humedezca la parte
interior con agua Humedecer o interior com
água Zwilżyć wnętrze wodą
Filter Filtro Filtro Filtr siatkowy
Sleufschroevendraaier Destornillador plano Chave de fenda Wkrętak płaski
Snelkoppeling Junta de un toque Junta de um toque Szybkozłącze
Aanzuigslang inschuiven Introduzca la manguera
de aspiración Insira a mangueira de
aspiração Włożyć wąż ssący
Eerst door de ring steken Pásela primero por la
anilla Passar primeiro pelo anel Najpierw przeprowadzić
go przez pierścień
Slanguiteinde Extremo de manguera Extremidade da
mangueira Koniec węża
Inschuiven tot voorbij dit
punt Introzcalo pasado este
punto Inserir para além deste
ponto Wsunąć go za ten punkt
Verzameld water Agua acumulada Água acumulada Nagromadzona woda
Hogedrukslang Manguera de alta presión Mangueira de alta
pressão Wąż wysokiego ciśnienia
Schakelaar Interruptor Interruptor Przełącznik
Trekker Gatillo Gatilho Spust
Midden van de trekker Centro del gatillo Centro do gatilho Środek spustu
Drukken Presionar Pressionar Przycisk
8
Nederlands Español Português Polski
Trekkerstop Tope del gatillo Batente do gatilho Ogranicznik spustu
Vergrendelen Bloquear Bloqueio Blokada
Ontgrendelen Soltar Soltar Zwolnienie
Loszetten Soltar Desapertar Poluzować
Reinigingspen voor
sproeier Clavija de limpieza de la
boquilla Pino de limpeza do bocal Kołek do czyszczenia
dyszy
Gat in de sproeier Ori cio de la boquilla Orifício do bocal Otr dyszy
Variabele sproeier Boquilla variable Bocal variável Dysza regulowana
Turbosproeier Boquilla turbo Bocal turbo Dysza Turbo
Sproeier es met
reinigingsmiddel Boquilla de bote de
detergente Bocal da garrafa de
detergente Dysza butelki z
detergentem
9
Magyar Türkçe
14 - 15 mm 14 ila 15 mm
20 mm vagy kevesebb 20 mm veya daha az
Kábel tartó Kablo tutucu
Mosó nyúlvány Yıkayıcı çıkıntısı
Markolat Tutamak
Csavar Vida
Tápfeszültség dugó Elektrik şi
Vízeltó bemenet Su besleme girişi
Vízeltó bemenet
sapka Su besleme girişi
kapağı
Vízeltó csatlakozó Su besleme bağlantısı
Víz kimenet Su çıkışı
Víz kimenet sapka Su çıkışı kapağı
O-gyűrűHalka conta
RögzítőgyűrűHalka
Meghúzni Sıkın
Működtető pisztoly Tetikleme tabancası
Csatlakozó Bağlantı aparatı
Szórófej Ağızlık
Nyúlvány Çıkıntı
Permet Sprey
Sugár Püskürtme
Tisztítószer szórófej Deterjan ağızlığı
Vízellátó csőSu sağlama borusu
Tartály Şişe
Szívó tömlőEmiş hortumu
mlő bilincs Hortum bandı
Nedvetse meg a
belsejét vízzel İç kısmı su ile
nemlendirin
SzűrőSüzgeç
Laposfejű csavarhúzó Düz tornavida
Gyorscsatlakozó Tek dokunuşlu mafsal
Illessze be a s
tömlőtEmiş borusunu
yerleştirin
Először vezesse át a
gyűrűnÖncelikle halkadan
geçirin
mlő vége Hortum ucu
Tolja túl ezen a ponton Bu noktadan girin
Összegyűlt víz Biriken su
Magasnyomású tömlőYüksek basınçlı hortum
Kapcsoló Sviç
Ravasz Tetik
A ravasz közepe Tetik merkezi
Nyomni İtin
Magyar Türkçe
Ravasz rögzítőTetik stoperi
Zár Kilit
Kiol Serbest bırakma
Meglazítani Gevşetin
Szórófej tisztító tüske Ağızlık temizleme iğnesi
A szófej nyísa Ağızlık deliği
Állítható szórófej Değişken ağızlık
Turbó szórófej Turbo ağızlık
Tisztítószer tartály
szórófej Deterjan şişesi ağızlığı
10
English Deutsch Français Italiano
Symbols
WARNING
The following show
symbols used for the
machine. Be sure that you
understand their meaning
before use.
Symbole
WARNUNG
Die folgenden Symbole
werden für diese Maschine
verwendet. Achten Sie
darauf, diese vor der
Verwendung zu verstehen.
Symboles
AVERTISSEMENT
Les symboles suivants
sont utilisés pour l’outil.
Bien se familiariser
avec leur signi cation
avant d’utiliser l’outil.
Simboli
AVVERTENZA
Di seguito mostriamo
i simboli usati per la
macchina. Assicurarsi
di comprenderne il
signi cato prima dell’uso.
To reduce the risk of
injury, user must read
instruction manual.
Failure to follow
the warnings and
instructions may result
in electric shock, re
and/or serious injury.
Der Anwender muss die
Bedienungsanleitung
lesen, um das Risiko
einer Verletzung zu
verringern.
Wenn die Warnungen
und Anweisungen nicht
befolgt werden, kann es
zu Stromschlag, Brand
und/oder ernsthaften
Verletzungen kommen.
Pour réduire les risques
de blessures, l’utilisateur
doit lire le manuel
d’utilisation.
Tout manquement
à observer ces
avertissements et
instructions peut engendrer
des chocs électriques,
des incendies et/ou des
blessures graves.
Per ridurre il rischio
di lesioni, l’utente
deve leggere il
manuale delle
istruzioni.
La mancata osservanza
degli avvertimenti e
delle istruzioni potrebbe
essere causa di scosse
elettriche, incendi e/o
gravi lesioni.
Only for EU countries
Do not dispose of electric
tools together with
household waste material!
In observance of European
Directive 2012/19/EU
on waste electrical and
electronic equipment
and its implementation in
accordance with national
law, electric tools that
have reached the end of
their life must be collected
separately and returned
to an environmentally
compatible recycling facility.
Nur für EU-Länder
Werfen Sie
Elektrowerkzeuge nicht
in den Hausll!
Gemäss Europäischer
Richtlinie 2012/19/EU
über Elektro- und
Elektronik- Altgeräte
und Umsetzung in
nationales Recht
müssen verbrauchte
Elektrowerkzeuge
getrennt gesammelt und
einer umweltgerechaten
Wiederververtung
zugeführt werden.
Pour les pays euroens
uniquement
Ne pas jeter les appareils
électriques dans les ordures
ménagères!
Conformément à la directive
européenne 2012/19/UE
relative aux déchets
d’équipements électriques
ou électroniques (DEEE),
et à sa transposition dans
la législation nationale,
les appareils électriques
doivent être collecs à
part et être soumis à un
recyclage respectueux de
l’environnement.
Solo per Paesi UE
Non gettare le
apparecchiature elettriche
tra i ri uti domestici.
Secondo la Direttiva
Europea 2012/19/UE sui
ri uti di apparecchiature
elettriche ed elettroniche
e la sua attuazione
in conformità alle
norme nazionali, le
apparecchiature elettriche
esauste devono essere
raccolte separatamente, al
ne di essere reimpiegate in
modo eco-compatibile.
High-pressure water
can be dangerous if
used incorrectly. High-
pressure water jets
must not be directed
at people, electrical
equipment or the
washer itself.
Wasser unter hohem
Druck kann bei falscher
Benutzung gehrlich
sein. Der Hochdruckstrahl
darf nicht auf Menschen,
elektrische Anlagen,
oder den Reiniger selbst
gerichtet werden.
L'eau sous haute pression
peut être dangereuse
si elle n'est pas utilisée
correctement. Un jet
d'eau sous haute pression
ne doit pas être dirigé
vers des personnes, des
équipements électriques ou
le nettoyeur.
L'acqua ad alta pressione
può essere pericolosa,
se utilizzata in modo
scorretto. Non puntare il
getto ad alta pressione
dell'idropulitrice verso
persone, apparecchiature
elettriche o l'idropulitrice
stessa.
Water that has passed
through the back ow
valve cannot be used
for drinking.
Wasser, das durch
das Rück ussventil
ge ossen ist, ist nicht
trinkbar.
L'eau qui est passée à
travers le clapet anti-
retour n'est pas potable.
L'acqua che ha
attraversato la valvola
antiri usso non è
potabile.
Alternating current Wechselstrom Courant alternatif Corrente alternata
Class II tool Werkzeug der Klasse II Outil classe II Attrezzo di Classe II
Warning Warnung Avertissement Avvertenza
VVolts Volt Volts Volt
AAmperes Ampere Ampères Ampere
Hz Hertz Hertz Hertz Hertz
WWatts Watt Watts Watt
kg Kilograms Kilogramm Kilogrammes Kilogrammi
MPa Megapascals Megapascal Mégapascals Megapascal
11
Nederlands Español Português Polski
Symbolen
WAARSCHUWING
Hieronder vindt u de symbolen
die voor dit toestel worden
gebruikt. Zorg ervoor dat u de
betekenis van de symbolen
begrijpt voordat u het toestel
begint te gebruiken.
Símbolos
ADVERTENCIA
A continuación se
muestran los símbolos
usados para la máquina.
Asegúrese de comprender
su signi cado antes del
uso.
Símbolos
AVISO
A seguir aparecem os
símbolos utilizados pela
máquina. Assimile bem
seus signi cados antes
do uso.
Symbole
OSTRZEŻENIE
Następujące oznaczenia
to symbole używane w
instrukcji obsługi maszyny.
Upewnij się, że rozumiesz
ich znaczenie zanim
użyjesz narzędzia.
Om het risico op
verwondingen te
verminderen, moet
de gebruiker de
instructiehandleiding lezen.
Als u geen rekening houdt met
de waarschuwingen en met de
instructies, stelt u zichzelf bloot
aan allerlei gevaren, zoals
elektrische schokken, brand
en/of ernstige blessures.
Para reducir el riesgo
de lesiones, el usuario
deberá leer el manual
de instrucciones.
Si no se siguen
las advertencias e
instrucciones, podría
producirse una
descarga eléctrica,
un incendio y/o daños
graves.
Para reduzir o risco
de lesão, o utilizador
deve ler o manual de
instruções.
Se não seguir todas
as instrões e os
avisos, pode provocar
um choque eléctrico,
incêndio e/ou
ferimentos graves.
Aby zmniejszyć ryzyko
odniesienia obrażeń,
użytkownik powinien
przeczytać instrukcję obsługi.
Nieprzestrzeganie
ostrzeżeń oraz wskazówek
bezpieczeństwa może
spowodować porażenie
prądem elektrycznym, pożar
i/lub odniesienie poważnych
obrażeń.
Alleen voor lidstaten van de EU
Verwijder elektrische
gereedschappen niet samen
met huishoudelijk afval. In
overeenstemming met de
Europese Richtlijn 2012/19/EU
betre ende afgedankte
elektrische en elektronische
apparatuur en de omzetting
van deze richtlijn in nationale
wetgeving moeten elektrische
gereedschappen na a oop
van hun nuttige levensduur
afzonderlijk worden opgehaald
en naar een milieuvriendelijk
recyclagebedrijf worden
gebracht.
lo para países de la Unn
Europea
¡No deseche los aparatos
eléctricos junto con los residuos
domésticos!
De conformidad con la Directiva
Europea 2012/19/UE
sobre residuos de aparatos
eléctricos y electrónicos y su
aplicación de acuerdo con
la legislación nacional, las
herramientas eléctricas cuya
vida útil haya llegado a su n se
deben recoger por separado
y trasladar a una planta de
reciclaje que cumpla con las
exigencias ecológicas.
Apenas para países da UE
Não deixe ferramentas
eléctricas no lixo
doméstico!
De acordo com a directiva
europeia 2012/19/UE
sobre ferramentas
eléctricas e electrónicas
usadas e a transposição
para as leis nacionais, as
ferramentas eléctricas
usadas devem ser
recolhidas em separado
e encaminhadas a uma
instalação de reciclagem
dos materiais ecológica.
Dotyczy tylko państw UE
Nie wyrzucaj
elektronarzędzi wraz z
odpadami z gospodarstwa
domowego!
Zgodnie z Europejską
Dyrektywą 2012/19/UE w
sprawie zużytego sprzętu
elektrotechnicznego i
elektronicznego oraz
dostosowaniem jej
do prawa krajowego,
zużyte elektronarzędzia
należy posegregować
i zutylizować w sposób
przyjazny dla środowiska.
Water onder hoge druk kan
gevaarlijk zijn als het niet op de
juiste manier wordt gebruikt.
Waterstralen onder hoge
druk mogen niet op mensen,
elektrische apparatuur of de
hogedrukreiniger zelf worden
gericht.
El agua a alta presn
puede ser peligrosa si se
utiliza incorrectamente.
Los chorros de agua a alta
presn no deben dirigirse
hacia las personas, el
equipo ectrico o la misma
máquina de limpieza.
A água a alta preso
pode ser perigosa quando
utilizada incorretamente. Os
jatos de água a alta preso
não devem ser direcionados
para pessoas, equipamento
elétrico ou o próprio
dispositivo.
Woda pod wysokim ciśnieniem
może być niebezpieczna,
jeżeli jest nieprawidłowo
wykorzystywana. Strumienia
wody pod wysokim ciśnieniem
nie wolno kierować na ludzi,
urządzenia elektryczne lub
samą myjkę.
Water dat doorheen de
terugslagklep geleid is,
mag niet als drinkwater
worden gebruikt.
El agua que ha
pasado por la válvula
antirretorno no puede
utilizarse para beber.
A água que passe pela
válvula de re uxo não
pode ser utilizada para
beber.
Wody, która przeszła
przez zawór zwrotny nie
wolno wykorzystywać
do picia.
Wisselstroom Corriente alterna Corrente alternada Prąd przemienny
Gereedschap van
Klasse II Herramienta de Clase II Feramenta de classe II Narzędzie klasy II
Waarschuwing Advertencia Aviso Ostrzeżenie
VVolt Voltios Volts Wolty
AAmpère Amperes Amperes Ampery
Hz Hertz Hertz o hercios Hertz Herce
WWatt Watts o vatios Watts Waty
kg Kilogram Kilogramos Quilogramas Kilogramy
MPa Megapascal Megapascales Megapascais Megapaskale
12
Magyar Türkçe
Jelölések
FIGYELEM
Az alábbiakban a géphez
alkalmazott jelölések
vannak felsorolva. A
gép használata előtt
feltétlel ismerje meg
ezeket a jeseket.
Simgeler
DİKKAT
Aşağıda, bu alet için kullanılan
simgeler gösterilmiştir.
Aleti kullanmadan önce
bu simgelerin ne anlama
geldiğini anladığınızdan emin
olun.
A sérülések
kockázatának
csökkentése érdekében,
a használónak el kell
olvasnia a használati
útmutatót.
A gyelmeztetések
és utasok be nem
tartása áramütést, tüzet
és/vagy súlyos sérülést
eredményezhet.
Kullanıcı yaralanma
riskini azaltmak için
kullanım kılavuzunu
okumalıdır.
Uyarılara ve talimatlara
uyulmaması elektrik
çarpmasına, yangına
ve/ veya ciddi
yaralanmaya neden
olabilir.
Csak EU-országok
számára
Az elektromos
kéziszerszámokat
ne dobja a háztarsi
szemétbe!
A használt villamos
és elektronikai
készülékekről szóló
2012/19/EU irányelv és
annak a nemzeti jogba
való átültetése szerint az
elhasznált elektromos
kéziszerszámokat
n kell gyűjteni, és
környezetbat módon
újra kell hasznosítani.
Sadece AB ülkeleri için
Elektrikli el aletlerini
evdeki çöp kutusuna
atmayınız!
Kullanılmış elektrikli
aletleri, elektrik ve
elektronikli eski cihazlar
hakkındaki 2012/19/AB
Avrupa yönergelerine
re ve bu yönergeler
ulusal hukuk kurallarına
re uyarlanarak, ayrı
olarak toplanmalı ve
çevre şartlarına uygun
bir şekilde tekrar
değerlendirmeye
gönderilmelidir.
A magasnyosú víz
veszélyes lehet, ha
helytelenül használja.
A magasnyomású
vízsugarat nem szabad
közvetlel ember,
elektromos berendezés
vagy maga a mosó felé
irányítani.
Yüksek basınçlı su hatalı
kullanıldığında tehlike
arz edebilir. Yüksek
bacınçlı su püsrtme
işlemi insanlara,
elektrikli ekipmanlara
veya yıkayıcının
kendisi üzerine doğru
uygulanmamalıdır.
A visszafolyó szelepen
áthaladó víz nem iható. Ters akım vanasından
geçen su içme amlı
olarak kullanılamaz.
Váltóáram Alternatif akım
II. osztályú szerszám Sınıf II aracı
Figyelem Dikkat
VVolt Volt
AAmper Amper
Hz Hertz Hertz
WWatt Watt
kg Kilogramm Kilogram
MPa Megapascal Megapaskal
English
13
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
1. Make sure the work area is always kept neat and
tidy.
Failure to observe this may result in accidents.
2. Take the surrounding environment into
consideration when using the washer.
Make sure the work area is brightly lit.
Do not use the washer near ammable liquid or gas.
3. Beware of electric shocks.
Do not touch anything that is earthed (grounded) when
using the High Pressure Washer. (For example, pipes,
heaters, microwave ovens, refrigerators, etc.)
4. Do not use the washer near children.
People other than the person using the washer must not
be allowed to touch the washer or the cord.
People other than the person using the washer must not
come near the work area.
5. Store the washer in a safe place when not in use.
Store the washer in a dry, high location or protected with
a lock out of the reach of children.
6. Do not use the washer in inappropriate ways.
Use the High Pressure Washer within the limits of its
capabilities to ensure safe and e cient results.
Do not use the washer for any purpose other than that for
which it was designed.
7. Wear safe clothing when using the washer.
Use safety boots, gloves, helmets with visors and
earplugs in accordance with necessity.
8. Use protective goggles and dust-protection masks
when using the washer.
There is a chance that splashes and dust may enter the
eyes and mouth when using the washer.
9. Do not handle the power cord roughly.
Do not carry the High Pressure Washer with only the
power cord or pull the plug from the socket while holding
the power cord.
Keep the power cord away from heat, oil and sharp
corners.
10. Make sure the item being cleaned is rmly xed in
place.
There are cases in which the power of the water pressure
will cause light objects to y o . Do not use the washer on
light objects that cannot be xed in place.
11. Maintain a proper stance when using the washer.
Make sure your feet are always placed rmly on the
ground to maintain balance.
12. Pay close attention to maintaining the High Pressure
Washer.
Clean the washer regularly to ensure safe and e cient
use.
Refer to the instruction manual when replacing supplied
parts.
Regularly check the power cord and ask your dealer for
repairs in the event of it being damaged.
If using an extension cord, check it regularly and replace
it in the event of it being damaged.
Make sure the grip is always kept dry and clean, and do
not allow oil of grease to come into contact with it.
13. Switch o and unplug the High Pressure Washer in
the following situations:
When it is not in use and when it is being repaired.
When attaching or detaching supplied or purchased
parts.
In other situations in which risks seem apparent.
14. Always remove equipment used for adjustment
purposes.
Check to make sure that all equipment used for
adjustment purposes has been removed before switching
on the power.
15. Avoid accidentally switching on the power.
Make sure you do not accidentally switch on the power to
the washer when it is plugged in.
Check to make sure that the washer is switched o
before plugging it into the power supply.
16. Inadequate extension cords can be dangerous.
17. Pay attention at all times when using the washer.
Pay attention to the methods of use stipulated in the
instruction manual and the surrounding environment
when using the High Pressure Washer.
Do not use the washer when tired.
18. Only use speci ed accessories and attachments.
Using accessories and attachments other than those
speci ed in the instruction manual or in HiKOKI catalogs
may result in accidents or injuries and must be avoided at
all costs.
19. High Pressure Washer repairs to be performed only
by experts.
The High Pressure Washer conforms to all relevant
safety regulations and must not be modi ed.
All repairs must be requested to HiKOKI authorized
service centers. Attempting to carry out repairs without
the correct skills may result in accidents or injuries.
20. Do not use the machine if a supply cord or important
parts of the machine are damaged, e.g. safety
devices, high pressure hoses, trigger gun.
21. Use a power supply that conforms to the voltage
listed on the name plate.
Failure to observe this may result in the washer operating
at higher speeds than normal, leading to overheating
and the outbreak of smoke and re, which may cause
damage or injuries.
22. Use an independent power socket with a rated value
of 15 A or more.
Sharing a power socket with other equipment may result
in the breaker shutting down.
23. Hold the trigger gun rmly in both hands when
using the washer.
Failure to observe this may result in injury.
24. High-pressure water can be dangerous if used
incorrectly.
High-pressure water jets must not be directed at people,
animals, easily-broken items, electrical equipment or the
washer itself.
25. Do not use gasoline, oil, organic solvents or
other in ammable or toxic liquids, or any other
inappropriate liquid.
Failure to observe this may result in explosions, the
outbreak of re or smoke, or other accidents, which may
cause damage or injury.
(Original instructions)
English
14
33. If the washer is accidently dropped or banged into
something solid, inspect it for damage, cracks and
malformation.
Failure to observe this may result in injury.
34. Do not direct the jet against yourself or others in
order to clean clothes or foot-wear.
35. Always switch o the mains disconnecting switch
when leaving the machine unattended.
CAUTION
1. Purge all of the pressure within the washer before
disconnecting the high-pressure hose.
2. Attach all supplied accessories correctly in
accordance with the instruction manual.
Failure to observe this may result in the accessories
becoming detached or in injury.
3. Check to make sure that no foreign matter is
adhering to the object being washed.
Failure to observe this may result in the matter ying o
and causing unexpected injury.
4. Do not spray a jet of water at the areas surrounding
labels on the object being washed.
Failure to observe this may result in the labels peeling o .
5. Grip the handle rmly when carrying the washer.
6. Do not use any accumulated water other than clean
water from the faucet (water containing dirt, mud,
sand, etc.) when using the auto-suction function.
7. Children should be supervised to ensure that they
don't play with the appliance.
26. When washing automobile tires, make sure that the
tip of the nozzle is kept at least 50cm distant from
the surface being washed.
Failure to observe this may result in damage to the tire or
brakes, which may cause serious accidents.
27. Do not touch the power plug or power socket with
wet hands.
Failure to observe this may result in electric shocks.
28. High pressure cleaners shall not be used by children
or untrained personnel.
29. Water that has own through back ow preventers is
considered to be non-potable.
Make sure that a back ow valve is used without fail when
connecting the washer to a drinking water faucet.
Water that has passed through the back ow valve cannot
be used for drinking.
30. Make sure that water is not splashed onto the High
Pressure Washer, power cord, extension cable,
power plug, power socket or other areas. Also,
neither exposes it to rain nor use it in the rain.
Failure to observe this may result in electric shocks.
31. Do not hold the trigger gun when xing it in place.
32. If the washer is not functioning normally or is
emitting strange noises or vibrations switch it o
immediately and contact HiKOKI authorized service
centers to request inspections or repairs.
Continued use may result in injury.
SPECIFICATIONS
Model AW130
Voltage (by areas)*1Single-phase AC 50/60 Hz
Voltage 220 V to 240 V
Power input*11600 W
Max. discharge pressure (1MPa: 10.2 kgf/cm2) 9.0 MPa
Max permissible pressure 13.0 MPa
Max feed pressure 0.7 MPa
Max water discharge 6.0 L/min
Permissible temperature 40 °C or less
Water feeding method Faucet connection type
Dimensions (Length × Width × Depth) 325 mm × 260 mm × 790 mm
(Including the handle, power cord holder and water feed connector)
Weight*28.3 kg
*1 Be sure to check the nameplate on product as it is subject to change by areas.
*2 Weight: Excluding the power cord, weight consists of trigger gun, high-pressure hose, variable nozzle, water feed connector
and accessory holder.
English
15
STANDARD ACCESSORIES
(1) Trigger gun ..................................................................1
(2) High-pressure hose (10 m) ..........................................1
(3) Variable nozzle ...........................................................1
(4) Turbo nozzle ...............................................................1
(5) Detergent bottle nozzle ...............................................1
(6) One-touch joint (black)
(For use with the strainer hose) ...................................1
(7) Water feed connector ..................................................1
(8) Nozzle cleaner pin .......................................................1
(9) Cord holder .................................................................1
(10)
Handle (with 4 attachment screws) .............................1
(1) (2)
(3) (4)
(5) (6)
(7) (8)
(9) (10)
English
16
OPTIONAL ACCESSORIES (sold separately)
Items shown in are sold separately. Contact HiKOKI authorized service centers for replacements if the standard
accessories become damaged or broken.
Variable nozzle
[Standard accessory]
Turbo nozzle
[Standard accessory]
Cleaning brush
Washes away dirt that has
been dislodged with the
brush.
Rotary brush
The central brush is rotated
by water pressure for cleaning
the windows and other items
with large surfaces.
Angle nozzle (variable)
Used for cleaning di cult-
to-reach places, such as
the underneath of cars and
ceilings, etc.
Pipe cleaning kit
(7.5 mm hose)
High-pressure water jets
from the front of the hose are
reversed to clean the inside
of the pipe.
Trigger gun
[Standard accessory]
High-pressure extension hose
(10 m)
Extends the length of the high-
pressure hose supplied.
High-pressure hose
[Standard accessory]
Water feed connector
[Standard accessory]
One-touch joint (black)
[Standard accessory]
Strainer hose set
Detergent bottle nozzle
[Standard accessory]
Accumulated water
English
17
APPLICATIONS
Cleans screen doors, window glass, oors, walls, etc.
Cleans automobiles, motorbikes, etc.
Cleans mud o gardening equipment and agricultural
equipment.
PRIOR TO OPERATION
1. Installation of an earth leakage circuit breaker
It is recommended that an earth leakage circuit breaker
is connected to the washer to shut o the power if leaking
current exceeds 30 mA for 30 milliseconds in order to
prevent electric shocks.
2. Keep the work area neat and tidy
Dirty water will be sprayed about when using the washer.
It is therefore necessary to check the area to make sure
there are no hindrances, and keep the work area neat
and tidy.
3. Situating the washer
Select at locations where the washer will not be
splashed with water when cleaning.
4. Using extension cords
Make sure the cord is thick enough to provide a constant
supply of electricity, and use cords that are as short as
possible.
Acceptable cord thicknesses (Nominal cross sectional
area cable) and cord length are indicated in the table
below.
Cord Thickness (mm2) Cord Length (m)
1 12.5
1.5 20
2.5 30
5. Prepare a water feed hose (Fig. 1)
Prepare the following when using water feed hoses:
Hoses that can withstand pressure (equipped with
meshes)
Hoses with an inner diameter of 14 to 15 mm.
Hoses with an outer diameter of 20 mm or less.
6. Attaching the cord holder (Fig. 2)
Align the groove on the cord holder with the protrusion on
the washer and insert it as far as it will go.
7. Attaching the handle (Fig. 3)
Use a Phillips screwdriver to rmly tighten all four screws.
INSPECTIONS PRIOR TO USE
WARNING
Check the following before using the washer. Check the
items listed in 1 and 2 before plugging into the power
socket.
1. Check to make sure the switch is at the “OFF”
position (Fig. 4)
Plugging the washer into the power socket with the
switch set at “ON” will cause the washer to immediately
begin operating, which may result in unexpected injuries.
2. Check the power supply
Only use a rated voltage.
Do not use motor engines are direct current. Failure to
observe this will not only result in damage to the washer,
it is also very dangerous.
3. Check the power socket
If the power socket is loose or the plug is easily dislodged,
it needs to be repaired.
It is dangerous to use it in this condition. Consult with
your local electrical engineering outlet.
ATTACHING PARTS
Make sure all parts are correctly attached in the following
sequence in order to guarantee safe usage.
WARNING
Switch o the washer and disconnect it from the power
socket without fail to prevent unexpected accidents.
1. Attach the water feed connector to the water feed
inlet on the washer (Fig. 5)
Remove the cap on the washer’s water feed inlet and
rmly attach the water feed connector.
Loose connections may result in water leaks.
2. Attaching the high-pressure hose to the washer’s
water outlet (Fig. 6)
Both ends of the high-pressure hose have the same
con guration, so either end may be connected.
Remove the water outlet cap from the washer, insert the
high-pressure hose into the water outlet and then rotate
the high-pressure hose ring to x it in place.
NOTE
Moisten the O-ring with water if it is di cult to insert the
hose.
If it is not possible to tighten the ring, it means that the
high-pressure hose has not been inserted far enough.
3. Attach the high-pressure hose to the trigger gun.
(Fig. 7)
Grip the thick end of the high-pressure hose, insert it into
the connector on the trigger gun, and then rotate the ring
on the hose to x it in place.
NOTE
Moisten the O-ring with water to facilitate the connection
if it is di cult to insert the hose.
If the ring cannot be tightened, it means that the end of
the high-pressure hose has not been su cient inserted.
4. Attach the nozzle to the trigger gun.
<Attachment (Fig. 8)>
(1) Align the protrusion on the nozzle with the entry hole on
the trigger gun and press it into place.
NOTE
Remove all dirt, mud and other matter from the trigger
gun’s entry hole and the protrusion on the nozzle.
Moisten the O-ring with water to facilitate the connection
if it is di cult to insert the nozzle.
(2) Press down rmly on the nozzle and then rotate it in the
direction of the arrow until it stops (half rotation.)
(3) Check to make sure that the nozzle cannot be pulled out
once it has been attached.
<Detachment (Fig. 9)>
Press down rmly on the nozzle and then rotate it counter-
clockwise until it stops. The nozzle can be withdrawn at
that position.
USING DIFFERENT NOZZLES
Variable nozzle (Fig. 10)
The variable nozzle can be used to alternation between
“Jet” and “Spray”.
Rotate the end on the nozzle clockwise for “Jet”, and
counter-clockwise for “Spray”.
• Jet washer
A water jet is discharged in a direct line to remove
stubborn mud and other dirt from agricultural machinery,
etc.
English
18
• Spray washer
The water is discharged in a wide fan for cleaning walls,
motorbikes and automobiles, etc.
The entire nozzle can be rotated by approximately 90
degrees to change the shape of the spray between
horizontal and vertical.
NOTE
Set the spray adjustment to “Jet” rst of all, and then
gradually move it to the “Spray” position while pulling the
trigger.
Note that there is a chance of the water being sprayed
horizontally over a wide area if this is rotated fully to the
“Spray” position.
Note that the nozzle may be damaged if it is forced to
move past the stop position when alternating between
“Jet” and “Spray”.
Turbo nozzle
The turbo nozzle rotates as it sprays high-pressure jets of
water for e cient washing.
NOTE
The turbo nozzle only discharges powerful jets of water
when set at the “Jet” mode.
Avoid using this on items that are easily broken or for
which coatings are easily peeled.
Detergent bottle nozzle (Fig. 11 and 12)
Sprays water mixed with detergent.
Uses neutral detergents available on the open market.
(1) Insert the water feed pipe into the detergent nozzle.
(2) Pour an undiluted neutral detergent into the bottle and
then screw the bottle onto the detergent nozzle.
(3) Attaching and removing the detergent bottle nozzle is the
same as explained for other nozzles.
When inserting the detergent bottle, make sure that
the trigger gun is pointing in the direction shown in the
illustration on the right.
(4) Aim the detergent nozzle at the article to be washed and
pull the trigger on the trigger gun to spray a mixture of
water and detergent at low pressure.
WARNING
Do not use acidic or alkali detergents. Use only neutral
detergents available on the open market.
Using detergents other than neutral detergents or
chemical agents may result in accidents or malfunctions.
NOTE
Moisten the O-ring with water if it is di cult to insert the
nozzle.
USING THE STRAINER HOSE SET (sold
separately)
The separately-sold strainer hose set is equipped with a
function that will automatically suck water from a water tank,
etc., when attached to the AW130.
The maximum height of suction (lifting range) is
approximately 0.5 m.
Attach this correctly in accordance with conditions.
Suction height when the height of the water feed outlet is
lower than the maximum height of the suction hose: From
the maximum height of the suction hose to the surface of
the water.
Less than 50 cm
Water surface
Water
feed inlet
Maximum height of the
suction hose
Suction height when the height of the water feed outlet is
the same as the maximum height of the suction hose: From
the water feed outlet to the surface of the water.
Less than 50 cm
Water surface
Water feed inlet
(maximum height of
the suction hose)
1. Attaching the strainer to the suction hose (Fig. 13)
(1) Pass the suction hose through the hose band supplied
and then gently moisten the inside of the suction hose
with water.
(2) Insert the strainer as far as it will go, and then rmly
tighten the hose band with a at-headed screwdriver.
2. Attaching the one-touch joint (black) to the suction
hose (Fig. 14)
Attach the one-touch joint (black) supplied as a standard
accessory to the suction hose.
3. Starting the suction hose water suction process
(Fig. 15)
Sink the strainer hose set into a container lled with
water.
Start o the suction process (introduce water to the
suction hose.)
NOTE
Do not use anything other than clean water (river or pond
water, muddy water containing sand granules.)
Failure to observe this may result in malfunctions.
Set the switch at “ON” without the nozzle attached.
Failure to observe this may result in dry operations,
leading to malfunctions.
4. Insert the one-touch joint into the water feed
connector (Fig. 16)
Withdraw the one-touch joint from the accumulated water
and insert it into the water feed connector on the washer
while making sure that the water inside the hose does not
escape.
English
19
5. Check to make sure the water is owing out
(Fig. 17)
(1) Connect the trigger gun from which the nozzle has been
removed to the high-pressure hose.
(2) Plug in the power socket and set the switch to “ON”.
(3) Pull the trigger gun’s trigger, and then set the switch to
“OFF” after checking that su cient water is owing out.
6. Attach the nozzle.
NOTE
Set the switch at “OFF” if water does not ow out within
two minutes.
Failure to observe this may result in malfunctions (dry
operations.)
7. Washing
Set the switch at “ON” and pull the trigger gun’s trigger to
commence washing.
8. Cleaning
Remove all dirt from the strainer’s grill, wash it with water
and store it after it has dried.
WASHING
WARNING
Do not switch the washer on while the trigger is being
pulled.
Failure to observe this may result in high-pressure water
being sprayed immediately, leading to unexpected
accidents.
Do not point the nozzle at people or animals.
Failure to observe this may result in injury.
CAUTION
Set the switch to “OFF” immediately if the hose becomes
detached from the faucet or washer, and if water is no
longer being fed to the washer.
Failure to observe this may result in immediate
malfunctions (dry operations.)
Set the switch to “OFF” without fail when temporarily
suspending operations.
Failure to observe this may result in the motor
automatically starting up.
Place your nger in the center of the trigger during
operations (Fig. 18)
Failure to observe this may result in injury from pinched
ngers.
Grip the gun and nozzle rmly with both hands.
The trigger gun may kick back when water is discharged.
NOTE
Do not use the water hose when it is wound onto the reel.
Failure to observe this may result in insu cient water
feed.
Commence initial washing approximately 2 to 3 meters
away from the targeted item, and then move gradually
closer while checking the level of cleaning until you reach
a distance in which soiling is e ectively washed away.
The pressure of the spray from the washer is
approximately 20-times greater than tap water. High-
pressure water jets may therefore damage or peel the
coating from the items being washed.
There are cases when the water spray will appear
unstable owing to the fact that air that has built up in
the pump and hose is purged together with the water
immediately after use. In this event, allow the water to
ow out until it stabilizes.
Leave two or more seconds gap between pulling and
releasing the trigger.
Failure to observe this may result in the pressure switch
malfunctions.
Do not use the washer for more than thirty consecutive
minutes without giving it a break.
1. Open the faucet to its fullest.
Point the nozzle in a safe direction and then fully open the
faucet. Check to make sure no water is leaking from the
joints.
Release the trigger stopper with the washer switched o ,
pull the trigger on the trigger gun to discharge a small
amount of water from the nozzle with just the pressure
from the tap water. Check to make sure that no water is
leaking.
NOTE
Do not switch the washer on with the faucet turned o .
Failure to observe this may result in malfunctions.
2. Set the switch to the “ON” position (Fig. 19)
The motor will start operating when the washer is
switched on. The motor will automatically switch o once
su cient water pressure has built up inside the washer.
3. Pull the trigger (Fig. 20)
Hold the trigger gun rmly in both hands, point the nozzle
at the item to be washed, and then pull the trigger.
The high-pressure water jet will spray out.
Adjust the nozzle between “Jet” and “Spray” in
accordance with need.
Trigger stopper (Fig. 21)
The trigger gun is tted with a trigger stopper to prevent
the trigger from being pulled.
The trigger is locked and released by pressing the
stopper in the direction shown by the arrows.
NOTE
Lock the trigger with the trigger stopper during pauses
and after washing has been completed.
ON COMPLETION OF USE
Once the targeted item has been washed, drain the residual
water from the washer and store it in a well-ventilated
location to dry.
There are cases in which water left in the hose may freeze
during the winter, so drain as much water as possible and
store it indoors.
WARNING
Make sure all residual water is drained from the washer,
the trigger gun and the hose, etc., after use.
Failure to observe this may result in freezing, leading to
malfunctions.
1. Draining water from the washer
(1) Stop the water supply.
(2) Set the switch to “ON” and pull the trigger on the trigger
gun to drain the water from the inside of the washer.
Continue this until water is no longer discharged
(approximately 30 to 60 seconds.)
(3) Press the trigger stopper on the trigger gun to lock it in
place.
2. Set the switch to “OFF”.
(1) Switch o the washer.
(2) Unplug the power cord from the mains socket.
NOTE
Leaving the washer switched on may result in dry
operations, leading to malfunctions.
3. Removing the high-pressure hose (Fig. 22)
(1) Loosen the ring.
(2) Remove the high-pressure hose from the washer’s water
outlet.
(3) Drain all residual water from the high-pressure hose.
English
20
4. Drain the water from the washer (Fig. 23)
(1) Tilt the washer to drain out the residual water.
(2) Wipe away all moisture with a dry cloth.
CAUTION
Water left in the washer may freeze in the winter, which
could result in damage to the pump.
SAFETY MECHANISMS
The washer is equipped with the following safety mechanisms
to ensure safe usage.
Power switch
This prevents the washer from being unintentionally
operated.
Trigger gun equipped with a lock
This prevents the trigger from being pulled, unintentionally
operating the washer.
Pressure switch
This prevents the pressure inside the washer from
exceeding permissible levels. Releasing the lever on the
trigger gun causes the valve operated by water pressure
to halt pump operations, which allows the pressure to be
released through the water feed. The pump is started
again when the lever is pulled.
Thermal protector
This protects the motor by halting operations when
abnormal heat is detected in the motor. It will start
operating again when the motor cools down.
MAINTENANCE AND INSPECTION
WARNING
Switch o the washer and disconnect the plug from the
power socket without fail when inspecting and cleaning it.
1. Inspecting the washer and hoses (Fig. 24)
Check to make sure that there is no damage, cracks or
malformations.
Make sure you clean the hole on the nozzle with the
nozzle cleaner pin supplied on a regular basis.
NOTE
Detach the trigger gun and clean the nozzle hole.
2. Inspecting the strainer (Fig. 25)
Wash all blockages out of the grid with water on a regular
basis.
NOTE
Withdraw the strainer from the water feed inlet with the
use of at radio pliers.
3. Clean the washer
Squeeze the excess moisture from a cloth soaked in
soap and water and wipe the washer.
Do not use gasoline, thinner, benzene, kerosene, etc.
Failure to observer this may result in malformations.
4. Check for loose screws.
Check for loose screws on a regular basis and tighten
any screws that are loose. Failure to observe this could
be dangerous.
5. Tidying up and storing the washer after use
(Fig. 26)
The accessories can be stored inside the washer as
shown in Fig. 26 when not in use and when being carried
around.
Avoid the following environments and store the washer
and accessories in a safe, dry location when not in use.
Do not store within the reach of children, or in locations
where children can use it.
Do not store in location where rain can reach it, such as in
front of the house, or in locations with high humidity.
Do not store in locations that are subject to drastic
changes in temperature or direct sunlight.
Do not store in locations containing volatile substances
that may ignite or explode.
6. Replacing supply cord
If the replacement of the supply cord is necessary, it has
to be done by a HiKOKI Authorized Service Center to
avoid a safety hazard.
7. Service parts list
CAUTION
Repair, modi cation and inspection of HiKOKI Power
Tools must be carried out by a HiKOKI Authorized
Service Center.
This Parts List will be helpful if presented with the tool to
the HiKOKI Authorized Service Center when requesting
repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
HiKOKI Power Tools are constantly being improved
and modi ed to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without prior
notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

Hikoki AW130 Kullanım kılavuzu

Tip
Kullanım kılavuzu