16 ENGLISH
3. During operation, never stand on an unstable
or slippery surface or a steep slope. During
the cold season, beware of ice and snow and
always ensure secure footing.
4. During operation, keep bystanders or animals
at least 15 m away from the tool. Stop the tool
as soon as someone approaches.
5. Never operate the tool while people, especially
children, or pets are nearby.
6. Before operation, examine the work area for
stones or other solid objects. They can be
thrown or cause dangerous kickback and result in
7. WARNING: Use of this product can create
dust containing chemicals which may cause
respiratory or other illnesses. Some examples
of these chemicals are compounds found in
pesticides, insecticides, fertilizers and herbi-
cides. Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed
Electrical and battery safety
1. Do not expose the tool to rain or wet condi-
tions. Water entering the tool will increase the risk
of electric shock.
2.
Do not use the tool if the switch does not turn it
Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
3.
Prevent unintentional starting. Ensure the switch
pack, picking up or carrying the tool. Carrying the
tool that have the switch on invites accidents.
4.
The cell may explode. Check with local codes for
possible special disposal instructions.
5. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
6. Do not charge battery in rain, or in wet
locations.
Putting into operation
1. Before assembling or adjusting the tool,
remove the battery cartridge.
2. Before handling the cutter blade, wear protec-
tive gloves.
3.
Before installing the battery cartridge, inspect
the tool for damages, loose screws/nuts or
improper assembly. Sharpen blunt cutter blade.
If the cutter blade is bent or damaged, replace
it. Check all control levers and switches for
easy action. Clean and dry the handles.
4. Never attempt to switch on the tool if it is dam-
aged or not fully assembled. Otherwise serious
5. Adjust the shoulder harness and hand grip to
suit the operator's body size.
6.
When inserting a battery cartridge, keep the cutting
attachment clear of your body and other object,
including the ground. It may rotate when starting and
7.
Remove any adjusting key, wrench or blade cover
before turning the tool on. An accessory left attached
8. The cutting tool has to be equipped with the
guard. Never run the tool with damaged guards
or without guards in place!
9. Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
Operation
1.
tool immediately.
2.
If you feel any unusual condition (e.g. noise,
and remove the battery cartridge. Do not use the
tool until the cause is recognized and solved.
3. The cutting attachment continues to rotate for
rush to contact the cutting attachment.
4. During operation, use the shoulder harness.
5.
Do not overreach. Keep proper footing and balance
at all times. Watch for hidden obstacles such as tree
stumps, roots and ditches to avoid stumbling.
6. Always be sure of your footing on slopes.
7. Walk, never run.
8.
Never work on a ladder or tree to avoid loss of control.
9.
If the tool gets heavy impact or fall, check the
condition before continuing work. Check the
controls and safety devices for malfunction. If
there is any damage or doubt, ask our authorized
service center for the inspection and repair.
10. Take a rest to prevent loss of control caused
by fatigue. We recommend taking a 10 to 20-min-
ute rest every hour.
11. When you leave the tool, even if it is a short
time, always remove the battery cartridge. The
unattended tool with the battery cartridge installed
may be used by unauthorized person and cause
serious accident.
12.
If grass or branches get caught between the
cutting attachment and guard, always turn the
cleaning. Otherwise the cutting attachment may
13.
Never touch moving hazardous parts before the
moving hazardous parts have come to a com-
plete stop and the battery cartridge is removed.
14. If the cutting attachment hits stones or other
Then remove the battery cartridge and inspect
the cutting attachment.
15. Check the cutting attachment frequently
during operation for cracks or damages.
Before the inspection, remove the battery
cartridge and wait until the cutting attachment
stops completely. Replace damaged cutting
attachment immediately, even if it has only