Dolmar DUR189 El kitabı

DUR189

EN

Cordless Grass Trimmer INSTRUCTION MANUAL 7

FR

Coupe herbe sans l MANUEL D’INSTRUCTIONS 17

DE

Akku-Rasentrimmer BETRIEBSANLEITUNG 28

IT

Tagliabordi a batteria ISTRUZIONI PER L’USO 39

NL

Accugrastrimmer GEBRUIKSAANWIJZING 50

ES

Cortador Inalámbrico de

Pasto

MANUAL DE

INSTRUCCIONES

61

PT

TESOURA PARA GRAMA A

BATERIA

MANUAL DE INSTRUÇÕES 72

DA

Akku græstrimmer BRUGSANVISNING 82

EL

Φορητό κουρευτικό γκαζόν ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ 92

TR

Akülü Yan Tırpan KULLANMA KILAVUZU 103

Fig.1

Fig.2

Fig.3

2

3

1

6

7

8

9

10

11

12

13

12

4

5

Fig.4

2

1

2

3

Fig.5

1

2

Fig.6

1

Fig.7

2

1

Fig.8

1

Fig.9

1

Fig.10

1

Fig.11

1

2

Fig.12

3

1

2

3

45

Fig.13

Fig.14

1

3

1

4

2

4

3

2

Fig.15

1

2

1

Fig.16

Fig.17

1

2

Fig.18

4

Fig.19

6

5

1

2

3

4

Fig.20

1

2

3

4

5

Fig.21

1

Fig.22

Fig.23

2

1

Fig.24

1

Fig.25

5

1

2

Fig.26

1

80 mm (3-1/8”)

Fig.27

100 mm (3-15/16”)

Fig.28

2

1

3

Fig.29

Fig.30

Fig.31

1

2

Fig.32

6

7 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: DUR189

No load speed

(without cutting tool)

4,000/5,000/6,000 min

-1

Overall length

(without cutting tool)

1,510 - 1,610 mm

Nylon cord diameter 2.0 - 2.4 mm

Applicable cutting tool and

cutting diameter

Nylon cutting head

(P/N 198971-4 / 198972-2)

300 mm

Plastic blade

(P/N 198383-1 / 198384-9)

255 mm

Rated voltage D.C. 18 V

Net weight 3.0 - 3.4 kg

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydifferfromcountrytocountry.

• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-

est combination, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /

BL1840B / BL1850 / BL1850B / BL1860B

Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

andchargersmaycauseinjuryand/orre.

Noise

Applicable standard : EN50636

Model Type Sound pressure level average

L

PA

(dB(A)) Uncertainty K (dB(A))

DUR189 Nylon cutting head 78 2.0

Plastic blade 78 3.7

• Even if the sound pressure level listed above is 80 dB (A) or less, the level under working may exceed 80 dB

(A). Wear ear protection.

Vibration

Applicable standard : EN50636

Model Type Left hand Right hand

a

h,W

(m/s

2

)

Uncertainty K (m/s

2

)

a

h,W

(m/s

2

)

Uncertainty K (m/s

2

)

DUR189 Nylon cutting head

2.5

0.4

2.5

0.1

Plastic blade

2.5

0.6

2.5

0.3

NOTE: The declared vibration emission value has been measured in accordance with the standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration emission value may also be used in a preliminary assessment of exposure.

8 ENGLISH

WARNING: The vibration emission during actual use of the power tool can differ from the declared emission

value depending on the ways in which the tool is used.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of

exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when

the tool is switched off and when it is running idle in addition to the trigger time).

Symbols

The following show the symbols used for the equip-

ment. Be sure that you understand their meaning before

use.

Take particular care and attention.

Read instruction manual.

Danger;beawareofthrownobjects.

The distance between the tool and

bystanders must be at least 15 m.

360°

Keep bystanders away.

15m(50FT)

Keep distance at least 15 m.

Wear a helmet, goggles and ear protection.

Wear protective gloves.

Wear sturdy boots with nonslip soles.

Steeltoed safety boots are recommended.

Do not expose to moisture.

Never use metal blade.

Ni-MH

Li-ion

Only for EU countries

Do not dispose of electric equipment or

battery pack together with household

waste material! In observance of the

European Directives, on Waste Electric

and Electronic Equipment and Batteries

and Accumulators and Waste Batteries and

Accumulators and their implementation

in accordance with national laws, electric

equipment and batteries and battery

pack(s) that have reached the end of

their life must be collected separately and

returned to an environmentally compatible

recycling facility.

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

IMPORTANT SAFETY

INSTRUCTIONS

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and

instructionsmayresultinelectricshock,reand/or

seriousinjury.

Save all warnings and instruc-

tions for future reference.

1. Be familiar with the controls and proper use of

the equipment.

2. Cutting elements continue to rotate after the

motor is switched off.

3. Never allow children or people unfamiliar with

the instructions to use the machine. Local reg-

ulations may restrict the age of the operator.

4. Stop using the machine while people, espe-

cially children, or pets are nearby.

5. Only use the machine in daylight or good

articial light. Avoid using the machine in bad

weather conditions especially when there is a

risk of lightning.

6. Before using the machine and after any

impact, check for signs of wear or damage and

repair as necessary.

7. Take care against injury from any device

tted for trimming the lament line length.

After extending new cutter line always return

the machine to its normal operating position

before switching on.

8. Never t metal cutting elements.

9. This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with

the appliance.

10.

Use the tool with the utmost care and attention.

11. Operate the tool only if you are in good phys-

ical condition. Perform all work calmly and

carefully. Use common sense and keep in mind

that the operator or user is responsible for

accidents or hazards occurring to other people

or their property.

12. Never operate the tool when tired, feeling ill or

under the inuence of alcohol or drugs.

13. The tool should be switched off immediately if

it shows any signs of unusual operation.

9 ENGLISH

14. Keep ngers away from switch trigger when

not operating the tool and when moving from

one operating position to another.

Intended use of the tool

1. Use right tool. The cordless grass trimmer is

only intended for cutting grass, light weeds. It

should not be used for any other purpose such

as hedge cutting as this may cause injury.

Personal protective equipment

►Fig.1

►Fig.2

1. Dress Properly. The clothing worn should be

functional and appropriate, i.e. it should be

tight-tting but not cause hindrance. Do not

wear either jewelry or clothing which could

become entangled with high grass. Wear pro-

tective hair covering to contain long hair.

2. When using the tool, always wear sturdy shoes

with a non-slip sole. This protects against

injuries and ensures a good footing.

3. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA, EN 166 in Europe, or AS/NZS 1336

in Australia/New Zealand. In Australia/New

Zealand, it is legally required to wear a face

shield to protect your face, too.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Electrical and battery safety

1. Avoid dangerous environment. Don't use the

tool in damp or wet locations or expose it to

rain. Water entering the tool will increase the

risk of electric shock.

2. Recharge only with the charger specied by

the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of

re when used with another battery pack.

3. Use power tools only with specically desig-

nated battery packs. Use of any other battery

packs may create a risk of injury and re.

4. When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another. Shorting the battery termi-

nals together may cause burns or a re.

5.

Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ush with water. If liquid

contacts eyes, seek medical help. Liquid ejected

from the battery may cause irritation or burns.

6. Do not dispose of the battery(ies) in a re. The

cell may explode. Check with local codes for

possible special disposal instructions.

7. Do not open or mutilate the battery(ies).

Released electrolyte is corrosive and may

cause damage to the eyes or skin. It may be

toxic if swallowed.

8. Do not charge battery in rain, or in wet

locations.

Starting up the tool

►Fig.3

1. Make sure that there are no children or other

people within a working range of 15 meters

(50 ft), also pay attention to any animals in the

working vicinity. Otherwise stop using the tool.

2. Before use always check that the tool is safe

for operation. Check the security of the cutting

tool and the guard and the switch trigger/lever

for easy and proper action. Check for clean

and dry handles and test the on/off function of

the switch.

3.

Check damaged parts before further use of

the tool. A guard or other part that is damaged

should be carefully checked to determine

that it will operate properly and perform its

intended function. Check for alignment of mov-

ing parts, binding of moving parts, breakage of

parts, mounting, and any other condition that

may affect its operation. A guard or other part

that is damaged should be properly repaired

or replaced by our authorized service center

unless indicated elsewhere in this manual.

4. Switch on the motor only when hands and feet

are away from the cutting tool.

5. Before starting make sure that the cutting

tool has no contact with hard objects such as

branches, stones etc. as the cutting tool will

revolve when starting.

6. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the tool.

Method of operation

1. Never operate the machine with damaged

guards or without the guards in place.

2. Only use the tool in good light and visibility.

During the winter season beware of slippery

or wet areas, ice and snow (risk of slipping).

Always ensure a safe footing.

3. Take care against injury to feet and hands from

the cutting tool.

4. Keep hands and feet away from the cutting

means at all times and especially when switch-

ing on the motor.

5. Never cut above waist height.

6. Never stand on a ladder and run the tool.

7. Never work on unstable surfaces.

8. Don't overreach. Keep proper footing and

balance at all times.

10 ENGLISH

9. Remove sand, stones, nails etc. found within

the working range. Foreign particles may

damage the cutting tool and can cause to be

thrown away, resulting in a serious injury.

10. Should the cutting tool hit stones or other hard

objects, immediately switch off the motor and

inspect the cutting tool.

11. Before commencing cutting, the cutting tool

must have reached full working speed.

12. During operation always hold the tool with

both hands. Never hold the tool with one hand

during use. Always ensure a safe footing.

13. All protective equipment such as guards

supplied with the tool must be used during

operation.

14. Except in case of emergency, never drop

or cast the tool to the ground or this may

severely damage the tool.

15. Never drag the tool on the ground when mov-

ing from place to place, the tool may become

damaged if moved in this manner.

16. Always remove the battery cartridge from the

tool:

— whenever leaving the tool unattended;

— before clearing a blockage;

— before checking, cleaning or working on

the tool;

— before making any adjustments, chang-

ing accessories or storing;

— whenever the tool starts vibrating

unusually;

— whenever transporting the tool.

17. Don't force the tool. It will do the job better and

with less likelihood of a risk of injury at the

rate for which it was designed.

18. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

19. Take a rest to prevent loss of control caused

by fatigue. We recommend to take a 10 to

20-minute rest every hour.

20. Do not use the tool on steep slopes.

21. The shoulder harness must be used during

operation, if supplied with the tool.

Maintenance instructions

1. The condition of the cutting tool, protec-

tive devices and shoulder harness must be

checked before commencing work.

2. Turn off the motor and remove the battery

cartridge before carrying out maintenance,

replacing the cutting tool and cleaning the

tool.

3. After use, disconnect the battery cartridge

from the tool and check for damage.

4. Check for loose fasteners and damaged parts

such as nearly halfway cut-off state in the

cutting tool.

5. When not in use store the equipment in a dry

location that is locked up or out of children's

reach.

6. Use only the manufacturer's recommended

replacement parts and accessories.

7. Always ensure that ventilation openings are

kept clear of debris.

8. Inspect and maintain the tool regularly, espe-

cially before/after use. Have the tool repaired

only by our authorized service center.

9. Keep handles dry, clean and free from oil and

grease.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery char-

ger, (2) battery, and (3) product using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11 ENGLISH

11. Follow your local regulations relating to dis-

posal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

PARTS DESCRIPTION

►Fig.4

1 Battery cartridge 2 Lock-off lever 3 Switch trigger 4 Speed indicator

5 Auto speed control

indicator

6 Power lamp 7 Main power button 8 Reverse button

9 Hanger 10 Lock sleeve 11 Handle 12 Protector (cutting tool

guard)

13 Shoulder harness - - - - - -

* The shape of the protector varies depending on the country.

FUNCTIONAL

DESCRIPTION

WARNING: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Failure to switch off and remove the battery cartridge

mayresultinseriouspersonalinjuryfromaccidental

start-up.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoffyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►Fig.5: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Status Indicator lamps

On Off Blinking

Overload

Overheat

Over

discharge

12 ENGLISH

Overload protection

If the tool is overloaded by entangled weeds or other

debris, and the middle indicators start blinking and

the tool automatically stops.

In this situation, turn the tool off and stop the application

that caused the tool to become overloaded. Then turn

the tool on to restart.

Overheat protection for tool or

battery

There are two types of overheating; tool overheating

and battery overheating. When the tool over heating

occurs, all speed indicators blink. When the battery over

heating occurs, indicator blinks.

If the overheating occurs, the tool stops automatically.

Let the tool and/or battery cool down before turning the

tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically and indicator blinks.

If the tool does not operate even when the switches are

operated, remove the batteries from the tool and charge

the batteries.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.6: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Power switch action

WARNING: Before installing the battery car-

tridge on the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released. Operating a tool

with a switch that does not actuate properly can lead

tolossofcontrolandseriouspersonalinjury.

CAUTION: Never put your nger on the

switch when carrying. The tool may start uninten-

tionallyandcauseinjury.

Press and hold the main power button for some sec-

onds to turn on the tool.

To turn off the tool, press and hold the main power

button again.

►Fig.7: 1. Main power button

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided.

To start the tool, grasp the handle (the lock-off lever is

released by the grasp) and then pull the switch trigger.

To stop the tool, release the switch trigger.

►Fig.8: 1. Lock-off lever 2. Switch trigger

NOTE: The tool is automatically turned off after the

tool is left one minute without any operations.

Speed adjusting

Youcanadjustthetoolspeedbytappingthemain

power button.

Each time you tap the main power button, the level of

speed will change.

►Fig.9: 1. Main power button

Indicator Mode Rotation speed

Auto 4,000 - 6,000 min

-1

High 6,000 min

-1

Medium 5,000 min

-1

Low 4,000 min

-1

13 ENGLISH

Reverse button for debris removal

WARNING: Switch off the tool and remove

the battery cartridge before you remove entan-

gled weeds or debris which the reverse rotation

function can not remove. Failure to switch off and

remove the battery cartridge may result in serious

personalinjuryfromaccidentalstart-up.

This tool has a reverse button to change the direction of

rotation. It is only for removing weeds and debris entan-

gled in the tool.

To reverse the rotation, tap the reverse button and pull

the trigger when the tool’s head is stopped. The power

lamp starts blinking, and the tool's head rotates in

reverse direction when you pull the switch trigger.

To return to regular rotation, release the trigger and wait

until the tool's head stops.

►Fig.10: 1. Reverse button

NOTE: During the reverse rotation, the tool operates

only for a short period of time and then automatically

stops.

NOTE: Once the tool is stopped, the rotation returns

to regular direction when you start the tool again.

NOTE: If you tap the reverse button while the tool's

head is still rotating, the tool comes to stop and to be

ready for reverse rotation.

Nylon cutting head

Optional accessory

NOTICE: The bump feed will not operate properly if

the head is not rotating.

►Fig.11: 1. Most effective cutting area

The nylon cutting head is a dual string trimmer head

provided with a bump & feed mechanism.

To feed out the nylon cord, tap the cutting head against

the ground while rotating.

NOTE:

If the nylon cord does not feed out while tap-

ping the head, rewind/replace the nylon cord by follow-

ing the procedures described under “Maintenance”.

Adjusting the shaft length

WARNING: Before adjusting the shaft length,

release the switch trigger and remove the battery

cartridge from the tool. Failure to release the trig-

ger and removing the battery cartridge may cause a

personalinjury.

CAUTION: Make sure to tighten the lock

sleeve before operation. Otherwise the tool may

losecontrolandresultinpersonalinjury.

Toadjustthelengthoftheshaft,turnthelocksleeve

counterclockwise until the arrow mark on the lock

sleeve indicates the unlock mark on the housing, and

pull out or push in the shaft to the desired length.

Afteradjustment,tightenthelocksleeveuntilthearrow

mark on the lock sleeve indicates the lock mark on the

housing.

►Fig.12: 1. Shaft 2. Lock sleeve

ASSEMBLY

WARNING: Always be sure that the tool is

switched off and battery cartridge is removed

before carrying out any work on the tool. Failure to

switch off and remove the battery cartridge may result

inseriouspersonalinjuryfromaccidentalstart-up.

WARNING: Never start the tool unless it is

completely assembled. Operation of the tool in a

partially assembled state may result in serious per-

sonalinjuryfromaccidentalstart-up.

Installing the handle

Fit the handle onto the shaft and secure it with the bolt

and the knob.

►Fig.13: 1. Handle 2. Bolt 3. Knob 4. Cutting tool

side 5. Battery cartridge side

Make sure that the handle is located in the straight area

oftheshaftasshowninthegure.

►Fig.14

Installing the protector

WARNING: Never use the tool without the

protector illustrated in place. Failure to do so can

causeseriouspersonalinjury.

CAUTION: Take care not to injure yourself on

the cutter for cutting the nylon cord.

NOTE: The shape of the protector varies depending

on the country.

1. Attach the protector and the protector holder to the

motorhousingasillustrated.Besuretottheprojec-

tions and grooves on them to their counter parts.

►Fig.15: 1. Protector 2. Groove 3.Projection

4. Protector holder

2. Tighten the hex socket head bolts securely to

fasten the protector and the protector holder.

►Fig.16: 1. Hex socket head bolt 2. Hex wrench

Installing the wire guard

CAUTION: Before adjusting the wire guard,

wait for the cutting head comes to standstill. Do

not adjust the wire guard with your foot.

►Fig.17

Toreducetheriskdamagingtheobjectsinfrontofthe

cutting head, insert the wire guard so that it controls the

cutting range of the mowing line.

Slightly expand the wire guard outward and then insert

it into the holes on the protector.

►Fig.18: 1. Wire guard 2. Hole (on both sides)

NOTICE: Do not expand the wire guard outward too

much. Otherwise it may break.

When wire guard is not in use, lift it for the idle position.

►Fig.19

14 ENGLISH

Installing nylon cutting head

Optional accessory

CAUTION: If the nylon cutting head acciden-

tally impacts a rock or hard object during oper-

ation, stop the tool and inspect for any damage.

If the nylon cutting head is damaged, replace it

immediately. Use of a damaged cutting tool could

resultinseriouspersonalinjury.

CAUTION: Be sure to remove the hex wrench

after installation.

NOTICE: Be sure to use genuine Makita nylon

cutting head.

►Fig.20: 1. Nylon cutting head 2. Metal guard

3. Spindle 4. Hex wrench 5. Tighten

6. Loosen

1. Turn the tool upside down so that you can replace

the cutting tool easily.

2. Insert the hex wrench through the hole on the

motor housing and rotate the spindle until the spindle is

locked.

3. Place the nylon cutting head onto the threaded

spindle directly and tighten it by turning in the tightening

directionasshowninthegure.

4. Remove the hex wrench.

To remove the nylon cutting head, turn it in the opposite

direction while locking the spindle with the hex wrench.

Installing plastic blade

Optional accessory

CAUTION: If the plastic blade accidentally

impacts a rock or hard object during operation,

stop the tool and inspect for any damage. If the

plastic blade is damaged, replace it immediately.

Use of a damaged cutting tool could result in serious

personalinjury.

CAUTION: Be sure to remove the hex wrench

after installation.

NOTICE: Be sure to use genuine Makita plastic

blade.

►Fig.21: 1. Plastic blade 2. Metal guard 3. Hex

wrench 4. Tighten 5. Loosen

1. Turn the tool upside down so that you can replace

the cutting tool easily.

2. Insert the hex wrench through the hole on the

motor housing and rotate the spindle until the spindle is

locked.

3. Place the plastic blade onto the threaded spindle

directly and tighten it by turning in the tightening direc-

tionasshowninthegure.

4. Remove the hex wrench.

To remove the plastic blade, turn it in the opposite direc-

tion while locking the spindle with the hex wrench.

Hex wrench storage

CAUTION: Be careful not to leave the hex

wrench inserted in the tool head. It may cause

injuryand/ordamagetothetool.

When not in use, store the hex wrench as shown in the

guretokeepitfrombeinglost.

►Fig.22: 1. Hex wrench

OPERATION

Correct handling of tool

WARNING: Always position the tool on your

right-hand side. Correct positioning of the tool allows

for maximum control and will reduce the risk of seri-

ouspersonalinjurycausedbykickback.

WARNING:

Be extremely careful to maintain

control of the tool at all times. Do not allow the tool

to be deected toward you or anyone in the work

vicinity. Failure to keep control of the tool could result

inseriousinjurytothebystanderandtheoperator.

WARNING:

To avoid accident, leave more than 15m

(50 ft) distance between operators when two or more oper-

ators work in one area. Also, arrange a person to observe

the distance between operators. If someone or an animal

enter the working area, immediately stop the operation.

►Fig.23

Attachment of shoulder harness

CAUTION:

Always use the shoulder harness

attached. Before operation, adjust the shoulder har-

ness according to the user size to prevent fatigue.

Connect the clasp of the shoulder harness to the hanger

part of the housing. Put the shoulder harness on. Be

sure that the buckles are locked completely in place.

►Fig.24: 1. Clasp 2. Hanger

Detachment

The buckle is provided with a means of quick release.

Simply squeeze the sides of the buckle to release the tool.

►Fig.25: 1. Buckle

MAINTENANCE

WARNING:

Always be sure that the tool is

switched off and battery cartridge is removed before

attempting to perform inspection or maintenance on the

tool. Failure to switch off and remove the battery cartridge

mayresultinseriouspersonalinjuryfromaccidentalstart-up.

NOTICE:

Never use gasoline, benzine, thinner, alcohol

or the like. Discoloration, deformation or cracks may result.

15 ENGLISH

Replacing the nylon cord

WARNING: Use nylon cord with diameter

specied in “SPECIFICATIONS” only. Never use

heavier line, metal wire, rope or the like. Use rec-

ommended nylon cord only, otherwise it may cause

damage to the tool and result in serious personal

injury.

WARNING: Make sure that the cover of the

nylon cutting head is secured to the housing

properly as described below. Failure to properly

secure the cover may cause the nylon cutting head to

yapartresultinginseriouspersonalinjury.

1. Press on the housing latches inward to lift off the

cover, then remove the spool.

►Fig.26: 1. Latch 2. Cover

2. Prepare approximately 3 m (9 ft) of new nylon

cord. Fold the new nylon cord with one end become

approximately80mm(3-1/8″)longerthantheother

end. Then hook the new nylon cord into the notch in the

center of the spool.

Windbothendsrmlyaroundthespoolinthedirection

of the head rotation (right-hand direction indicated by

RH on the side of the spool).

►Fig.27: 1. Spool

3. Windallbutabout100mm(3-15/16″)ofthe

cords, leaving the ends temporarily hooked through a

notch on the side of the spool.

►Fig.28

4.

Mount the spool in the housing so that the grooves and

protrusions on the spool match up with those in the housing.

Keep the side with letters on the spool visible on the top. Now,

unhook the ends of the cord from their temporary position and

feed the cords through the eyelets to come out of the housing.

►Fig.29: 1. Spool 2. Housing 3. Eyelet

5. Align the protrusion on the underside of the cover

withtheslotsoftheeyelets.Thenpushthecoverrmly

onto the housing to secure it.

►Fig.30

Replacing the plastic blade

Replace the blade if it is worn out or broken.

►Fig.31

When installing the plastic blade, align the direction of

the arrow on the blade with that of the protector.

►Fig.32:

1. Arrow on the protector 2. Arrow on the blade

To maintain product SAFETY and RELIABILITY,

repairs,anyothermaintenanceoradjustmentshould

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

TROUBLESHOOTING

Beforeaskingforrepairs,conductyourowninspectionrst.Ifyoundaproblemthatisnotexplainedinthemanual,

do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-

ment parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Motor does not run. Battery cartridge is not installed. Install the battery cartridge.

Battery problem (under voltage) Recharge the battery. If recharging is not effective,

replace battery.

The drive system does not work correctly.

Ask your local authorized service center for repair.

Motor stops running after a little use. Battery's charge level is low. Recharge the battery. If recharging is not effective,

replace battery.

Overheating. Stop using of tool to allow it to cool down.

It does not reach maximum RPM. Battery is installed improperly. Install the battery cartridge as described in this

manual.

Battery power is dropping. Recharge the battery. If recharging is not effective,

replace battery.

The drive system does not work

correctly.

Ask your local authorized service center for repair.

Cutting tool does not rotate:

stop the machine immediately!

Foreignobjectsuchasabranchis

jammedbetweentheprotectorandthe

cutting tool.

Removetheforeignobject.

The drive system does not work

correctly.

Ask your local authorized service center for repair.

Abnormal vibration:

stop the machine immediately!

One end of the nylon cord has been

broken.

Tap the nylon cutting head against the ground while

it is rotating to cause the cord to feed.

Plastic blade(s) is broken. Replace broken plastic blade(s) with new one(s).

The drive system does not work

correctly.

Ask your local authorized service center for repair.

Cutting tool and motor cannot stop:

Remove the battery immediately!

Electric or electronic malfunction. Remove the battery and ask your local authorized

service center for repair.

16 ENGLISH

OPTIONAL

ACCESSORIES

WARNING: Do not mount a metal blade on

this tool and only use the recommended accesso-

ries or attachments indicated in this manual. The

use of a metal blade or any other accessory or attach-

mentmayresultinseriouspersonalinjury.

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual. The use of any other

accessories or attachments might present a risk of

injurytopersons.Onlyuseaccessoryorattachment

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Nylon cutting head

• Nylon cord (cutting line)

• Plastic blade

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

differ from country to country.

17 FRANÇAIS

FRANÇAIS (Instructions originales)

SPÉCIFICATIONS

Modèle : DUR189

Vitesse à vide

(sans outil de coupe)

4 000/5 000/6 000 min

-1

Longueur totale

(sans outil de coupe)

1 510 - 1 610 mm

Diamètre du cordon en nylon 2,0 à 2,4 mm

Outil de coupe applicable et

diamètre de coupe

Têtedecoupeàlnylon

(P/N 198971-4 / 198972-2)

300 mm

Lame en plastique

(P/N 198383-1 / 198384-9)

255 mm

Tension nominale 18 V CC

Poids net 3,0 - 3,4 kg

• Étantdonnél’évolutionconstantedenotreprogrammederechercheetdedéveloppement,lesspécications

contenuesdanscemanuelsontsujettesàmodicationsanspréavis.

• Lesspécicationspeuventvariersuivantlespays.

• Le poids peut être différent selon les accessoires, notamment la batterie. Les associations la plus légère et la

plus lourde, conformément à la procédure EPTA 01/2014, sont indiquées dans le tableau.

Batterie et chargeur applicables

Batterie BL1815N / BL1820 / BL1820B / BL1830 / BL1830B / BL1840 /

BL1840B / BL1850 / BL1850B / BL1860B

Chargeur DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF

• Certains chargeurs et batteries répertoriés ci-dessus peuvent ne pas être disponibles selon la région où vous

résidez.

AVERTISSEMENT : N’utilisez que les batteries et les chargeurs répertoriés ci-dessus. L’utilisation

d’autres batteries et chargeurs peut provoquer des blessures et/ou un incendie.

Bruit

Norme applicable : EN50636

Modèle Type Niveau de pression sonore moyenne

L

PA

(dB(A)) Incertitude K (dB(A))

DUR189 Têtedecoupeàlnylon 78 2,0

Lame en plastique 78 3,7

• Même si le niveau de pression sonore indiqué ci-dessus est inférieur ou égal à 80 dB (A), le niveau en fonction-

nement peut dépasser 80 dB (A). Portez un serre-tête antibruit.

Vibration

Norme applicable : EN50636

Modèle Type Main gauche Main droite

a

h,W

(m/s

2

)

Incertitude K (m/s

2

)

a

h,W

(m/s

2

)

Incertitude K (m/s

2

)

DUR189

Têtedecoupeàlnylon

2,5

0,4

2,5

0,1

Lame en plastique

2,5

0,6

2,5

0,3

NOTE : La valeur d’émission de vibrations déclarée a été mesurée conformément à la méthode de test standard

et peut être utilisée pour comparer les outils entre eux.

NOTE : La valeur d’émission de vibrations déclarée peut aussi être utilisée pour l’évaluation préliminaire de

l’exposition.

18 FRANÇAIS

AVERTISSEMENT : L’émission de vibrations lors de l’usage réel de l’outil électrique peut être différente de

la valeur d’émission déclarée, suivant la façon dont l’outil est utilisé.

AVERTISSEMENT : Les mesures de sécurité à prendre pour protéger l’utilisateur doivent être basées sur

une estimation de l’exposition dans des conditions réelles d’utilisation (en tenant compte de toutes les compo-

santes du cycle d’utilisation, comme par exemple le moment de sa mise hors tension, lorsqu’il tourne à vide et le

moment de son déclenchement).

Symboles

Vous trouverez ci-dessous les symboles utilisés pour

l’appareil.Veillezàcomprendreleursignicationavant

toute utilisation.

Veuillez être prudent et rester attentif.

Lire le mode d’emploi.

Danger;prendregardeauxprojections

d’objets.

La distance entre l’outil et les badauds doit

être d’au moins 15 m.

360°

Tenir les personnes à l’écart.

15m(50FT)

Maintenez une distance d’au moins 15 m.

Portez un casque, des lunettes à coques et

un serre-tête antibruit.

Portez des gants de protection.

Portez des bottes robustes à semelles anti-

dérapantes. Il est conseillé de porter des

chaussures avec embout de sécurité.

Ne pas exposer à l’eau.

N’utilisezjamaisdelamemétallique.

Ni-MH

Li-ion

Uniquement pour les pays européens

Nejetezpaslesappareilsélectriquesou

les batteries avec vos ordures ménagères !

Conformément aux directives européennes

relatives aux déchets d’équipements

électriques et électroniques et aux piles

et accumulateurs ainsi qu’aux déchets de

piles et d’accumulateurs et leur mise en

œuvre conformément aux lois nationales,

les équipements électriques et les piles et

batteriesenndeviedoiventfairel’objet

d’unecollectesélectiveetêtreconésà

une usine de recyclage respectueuse de

l’environnement.

Déclaration de conformité CE

Pour les pays européens uniquement

La déclaration de conformité CE est fournie en Annexe

A à ce mode d’emploi.

CONSIGNES DE

SÉCURITÉ

CONSIGNES DE SÉCURITÉ

IMPORTANTES

AVERTISSEMENT : Lisez toutes les

consignes de sécurité et toutes les instructions. Il

y a risque d’électrocution, d’incendie et/ou de graves

blessures si les mises en garde et les instructions ne

sont pas respectées.

Conservez toutes les mises en

garde et instructions pour réfé-

rence ultérieure.

1. Familiarisez-vous avec les commandes et

l’utilisation correcte de l’appareil.

2. Les éléments de coupe continuent de tourner

une fois le moteur coupé.

3. Ne laissez jamais les enfants ou les personnes

qui ne sont pas familiarisées avec ces instruc-

tions utiliser la machine. Les réglementations

locales peuvent limiter l’âge de l’utilisateur.

4. Arrêtez d’utiliser la machine en présence de

personnes, particulièrement les enfants et

animaux domestiques, à proximité.

5. N’utilisez la machine qu’à la lumière du jour ou

sous un bon éclairage articiel. Évitez d’utili-

ser la machine par mauvais temps, particuliè-

rement en cas d’orage.

6. Avant d’utiliser la machine et après un impact,

vériez l’absence d’usure ou de dégât, et répa-

rez au besoin.

7. Prenez garde de ne pas vous blesser avec le

dispositif xé pour la coupe de la longueur du

lament. Après avoir allongé le l de coupe,

ramenez toujours la machine à sa position

de fonctionnement normal avant de la mettre

sous tension.

8.

Ne xez jamais d’éléments de coupe métalliques.

9. Cet appareil n’est pas destiné à être utilisé par

des personnes (y compris les enfants) aux

facultés physiques, sensorielles ou mentales

diminuées ou sans expérience ni expertise, à

moins qu’une personne responsable de leur

sécurité ne leur fournisse la surveillance et les

instructions nécessaires à l’utilisation de cet

appareil. Les enfants doivent être sous la sur-

veillance d’un adulte an de s’assurer qu’ils ne

jouent pas avec l’appareil.

10. Soyez toujours très prudent et attentif lorsque

vous utilisez l’outil.

19 FRANÇAIS

11. N’utilisez l’outil que si vous êtes en bonne

condition physique. Travaillez toujours en

faisant preuve de calme et de prudence. Faites

preuve de bons sens et gardez à l’esprit que

l’opérateur ou l’utilisateur est responsable des

accidents ou risques encourus par les per-

sonnes ou leur propriété.

12. N’utilisez jamais l’outil lorsque vous êtes

fatigué, malade ou sous l’emprise d’alcool, de

drogues ou de médicaments.

13. Si vous remarquez un fonctionnement inhabi-

tuel de l’outil, éteignez-le immédiatement.

14. Éloignez les doigts de la gâchette lorsque

vous n’utilisez pas l’outil et lorsque vous vous

déplacez d’un point à un autre.

Utilisation prévue de l’outil

1. Utilisez le bon outil. Le coupe herbe sans l

est exclusivement conçu pour couper l’herbe

ou les mauvaises herbes à racines nes. Il ne

doit pas être utilisé à d’autres ns, pour tailler

des haies, par exemple, sous peine de provo-

quer des blessures.

Équipement de protection individuelle

►Fig.1

►Fig.2

1. Portez des vêtements adéquats. Les vête-

ments portés doivent être fonctionnels et

adéquats, c’est-à-dire moulants sans être

toutefois gênants. Ne portez ni bijoux ni vête-

ments susceptibles de s’enchevêtrer dans

l’herbe haute. Portez un let à cheveux pour

retenir les cheveux longs.

2. Lorsque vous utilisez l’outil, portez toujours

des chaussures robustes à semelles antidéra-

pantes. Ceci vous protègera des blessures et

garantira un bon appui.

3. Pour protéger vos yeux des blessures lorsque

vous utilisez un outil électrique, portez tou-

jours des lunettes de protection, lesquelles

doivent être conformes à ANSI Z87.1 aux

États-Unis, EN 166 en Europe ou AS/NZS 1336

en Australie/Nouvelle-Zélande. En Australie/

Nouvelle-Zélande, la loi exige également le

port d’un écran facial pour se protéger le

visage.

L’employeur est responsable d’imposer le

port d’équipements de sécurité appropriés

par les utilisateurs de l’outil et par les autres

personnes se trouvant à proximité de la zone

de travail.

Sécurité électrique et sécurité des batteries

1. Évitez les environnements dangereux.

N’utilisez pas l’outil dans un endroit humide, ni

ne l’exposez à la pluie. Le risque d’électrocu-

tion augmente si de l’eau pénètre dans l’outil.

2.

Rechargez la batterie uniquement avec le char-

geur spécié par le fabricant. Un chargeur prévu

pour un type de batterie peut être à l’origine d’un

incendie s’il est utilisé avec une autre batterie.

3. Utilisez l’outil électrique uniquement avec la

batterie spéciquement indiquée. L’utilisation

de toute autre batterie peut présenter un

risque de blessure et d’incendie.

4.

Lorsque vous n’utilisez pas la batterie, tenez-la à

l’écart des objets métalliques, comme des trom-

bones, pièces de monnaie, clés, clous, vis ou

autres petits objets métalliques, susceptibles de

créer une connexion entre deux bornes. Court-

circuiter les bornes d’une batterie entre elles

peut provoquer des brûlures ou un incendie.

5.

Dans des conditions d’utilisation inadéquate, il

peut y avoir une fuite de l’électrolyte de la batterie.

Le cas échéant, évitez tout contact avec ce liquide.

En cas de contact accidentel, rincez à l’eau. Si le

liquide entre en contact avec les yeux, consultez

un médecin. Le liquide s’échappant de la batterie

peut provoquer une irritation ou des brûlures.

6. Ne jetez pas la ou les batteries au feu.

L’élément de la pile pourrait exploser.

Consultez les codes locaux pour de possibles

instructions de mise au rebut spéciales.

7. N’ouvrez ni ne manipulez la ou les batteries.

L’électrolyte qui s’échappe de la batterie est

corrosif et peut irriter la peau ou les yeux. Il

peut être toxique en cas d’ingestion.

8. Ne chargez pas la batterie sous la pluie ou

dans un endroit mouillé.

Mise en marche de l’outil

►Fig.3

1. Assurez-vous qu’il n’y a pas d’enfants ou

d’autres personnes dans un rayon de 15 m

autour de la zone de travail. Faites également

attention aux animaux à proximité. Autrement,

arrêtez d’utiliser l’outil.

2.

Avant de l’utiliser, vériez toujours la sécurité de

l’outil. Vériez la sécurité de l’outil de coupe, du

carter de protection et de la gâchette ou du levier

pour un fonctionnement facile et correct. Vériez

que les poignées sont propres et sèches et testez

la fonction de marche/arrêt de la gâchette.

3. Vériez qu’aucune pièce n’est endommagée

avant de continuer à utiliser l’outil. Vériez

soigneusement le carter de protection ou toute

autre pièce endommagés pour vous assurer

qu’ils fonctionnent bien et remplissent leurs

fonctions respectives. Assurez-vous que les

pièces en mouvement ne sont pas désalignées

ou coincées, qu’aucune pièce ou xation n’est

cassée ou la présence de toute autre condition

pouvant affecter le bon fonctionnement. Si le

carter de protection ou toute autre pièce sont

endommagés, ils doivent être réparés ou rem-

placés de manière adéquate par notre centre

de service après-vente agréé sauf indication

contraire dans ce manuel.

20 FRANÇAIS

4. Démarrez le moteur uniquement lorsque les

mains et les pieds sont éloignés de l’outil de

coupe.

5. Avant la mise en marche, assurez-vous que

l’outil de coupe n’entre pas en contact avec

des objets durs comme des branches, des

pierres ou autres, car l’outil de coupe tourne

au démarrage.

6. Assurez-vous qu’il n’y a pas de câbles élec-

triques, de conduites d’eau, de conduites

de gaz, etc., présentant un risque s’ils sont

endommagés suite à l’utilisation de l’outil.

Utilisation

1. N’utilisez jamais la machine si le carter de

protection est endommagé ou n’est pas posé.

2. N’utilisez l’outil qu’avec une bonne visibilité

et un bon éclairage. En hiver, faites attention

aux sols glissants ou aux zones humides,

à la glace et à la neige (risque de glissade).

Assurez-vous toujours d’avoir une bonne

assise.

3. Prenez garde de ne pas vous blesser les pieds

et les mains avec l’outil de coupe.

4. Éloignez les mains et les pieds du mécanisme

de coupe en tout temps et particulièrement au

démarrage du moteur.

5. Ne réalisez jamais de coupe plus haut que

votre taille.

6. N’utilisez jamais l’outil en vous tenant sur une

échelle.

7. Ne travaillez jamais sur des surfaces instables.

8. Ne vous penchez pas trop loin. Maintenez

constamment une bonne assise et un bon

équilibre.

9. Enlevez le sable, les pierres, les clous ou

autres se trouvant dans le rayon d’utilisation

de l’outil. Les corps étrangers peuvent endom-

mager l’outil de coupe et être projetés, provo-

quant de graves blessures.

10. Si l’outil de coupe heurte des pierres ou

d’autres objets durs, coupez immédiatement le

moteur et inspectez l’outil de coupe.

11. Attendez que l’outil de coupe atteigne sa

pleine vitesse pour commencer la coupe.

12. Tenez toujours l’outil à deux mains pendant

le fonctionnement. Ne tenez jamais l’outil

d’une seule main pendant le fonctionnement.

Assurez-vous toujours d’avoir une bonne

assise.

13. L’ensemble des dispositifs de protection

comme les carters de protection fournis avec

l’outil doivent être utilisés pendant le fonction-

nement de l’outil.

14. Sauf en cas d’urgence, ne laissez jamais tom-

ber l’outil, ni ne le lancez au sol sous peine de

gravement l’endommager.

15. Ne traînez pas l’outil au sol en vous déplaçant

d’un endroit à l’autre sous peine d’endomma-

ger l’outil.

16. Retirez toujours la batterie de l’outil :

— chaque fois que vous devez laisser l’outil

sans surveillance ;

— avant de débloquer l’outil ;

— avant d’effectuer la vérication, le net-

toyage ou l’entretien de l’outil ;

— avant d’effectuer tout réglage, de rempla-

cer des accessoires ou de ranger l’outil ;

— chaque fois que l’outil se met à vibrer de

manière inhabituelle ;

— chaque fois que vous transportez l’outil.

17. Ne forcez jamais sur l’outil. Si vous respectez

le régime pour lequel il a été conçu, il réalisera

un travail de meilleure qualité et avec moins de

risque de blessures.

18. N’utilisez pas un outil électrique dans un envi-

ronnement explosif, en présence de liquides,

gaz ou poussières inammables par exemple.

Les outils électriques produisent des étincelles

quipeuventenammerlapoussièreoules

émanations.

19. Reposez-vous régulièrement pour empêcher la

perte du contrôle due à la fatigue. Nous recom-

mandons de faire une pause de 10 à 20 minutes

toutes les heures.

20. N’utilisez pas l’outil dans les pentes trop

abruptes.

21. La bandoulière doit être utilisée pendant l’utili-

sation, si elle est fournie avec l’outil.

Instructions d’entretien

1. Vériez l’état de l’outil de coupe, des disposi-

tifs de protection et de la bandoulière avant de

commencer la tâche.

2. Coupez le moteur et retirez la batterie avant

d’effectuer l’entretien, de remplacer l’outil de

coupe ou de nettoyer l’outil.

3. Après utilisation, déconnectez la batterie de

l’outil et vériez les dégâts.

4. Assurez-vous qu’il n’y a pas de xations mal

serrées ni de pièces endommagées, comme

des chutes à moitié découpées dans l’outil de

coupe.

5. Rangez l’appareil dans un endroit sec fermé

ou hors de portée des enfants lorsque vous ne

l’utilisez pas.

6. N’utilisez que les pièces de rechange et acces-

soires recommandés par le fabricant.

7. Assurez-vous toujours que les bouches d’aé-

ration ne sont pas obstruées par des débris.

8. Procédez régulièrement à l’inspection et à

l’entretien de l’outil, particulièrement avant/

après son utilisation. Faites réparer l’outil

uniquement par notre centre de service après-

vente agréé.

9. Gardez toutes les poignées sèches, propres et

sans trace d’huile ou de graisse.

CONSERVEZ CES INSTRUCTIONS.

AVERTISSEMENT : NE vous laissez PAS

tromper (au l d’une utilisation répétée) par un

sentiment d’aisance et de familiarité avec le

produit, en négligeant le respect rigoureux des

consignes de sécurité qui accompagnent le pro-

duit en question. La MAUVAISE UTILISATION de

l’outil ou l’ignorance des consignes de sécurité

indiquées dans ce mode d’emploi peut entraîner

de graves blessures.

Sayfa yükleniyor ...

Dolmar DUR189 El kitabı

Dolmar DUR189 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler