Franke Consumer Products FPL 907 I XS 645H Kullanım kılavuzu

FPL 607 I

FPL 907 I

FPL 457 I XS 645H

FPL 607 I XS 645H

FPL 907 I XS 645H

IT

FR

DE

TR

HR

PL

GB

EN

2

IT

3

FR

4

DE

5

TR

6

HR

7

PL

8

!

! !

"

EN

9

650 mm min.

EN

1

0

10

*

**

*

**

EN

1

11

23

22

12h

11

15

24

1

12f

2

7.1

7.1b

7.1a

21

12g

12w

14

26

12c

13

9

25

EN

1

2

12

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the

template is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm(immediately insert

the Dowels 11 supplied).

• For wooden beam ceilings, drill according to the wood screws used.

• For wooden shelf, drill ø 7 mm.

• For the power supply cable feed, drill ø 10 mm.

• For the air outlet (Ducted Version), drill according to the diameter of the external air ex-

haust duct connection.

• Insert two screws of the following type, crossing them and leaving 4-5 mm from the ceiling:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• for Cavity ceiling with inner space, with wall thickness of approx. 20 mm, Screws 12h,

supplied.

• For wooden beam ceilings, use 4 wood screws (not provided).

• For wooden shelf, use 4 screws 12g with washers 22 and nuts 23, provided.

EN

1

3

13

If you wish to adjust the height of the frame, proceed

as follows:

• Unfasten the metric screws joining the two columns,

located at the sides of the frame.

• Adjust the frame to the height re

quired, then

replace all the screws removed as above.

• Fix the Fixing Part of the Upper Chimney 26 to the

hanging kit using the 2 screws 12w (M3 x 8).

• Lift up the frame, fit the frame slots onto the screws

up to the slot end positions.

• Tighten the two screws and fasten the other two

screws provided; before locking the screws com-

pletely, it is possible to adjust the frame by turning it,

making sure that the screws do not come out of their

housing in the adjustment slot.

• It is now possible to place and tighten the 4 safety

screws, Proceed as follows:

• drill the ceiling with a 10 mm ø bit taking as refer-

ence the holes of the side parts of the upper chim-

ney fixing part.

• insert the 4 dowels (provided).

• insert the washers (provided) to the screws and

tighten the screws

• The Frame must be securely fastened so as to support

both the weight of the Hood and the stress caused by

occasional axial pressure against the fitted Appli-

ance. After fixing, make sure that the base is stable

even when the Frame is subjected to lateral stress.

• If the Ceiling is not strong enough in the area where

the hood is to be fixed, the Installer must strengthen

the area using suitable plates and counterplates an-

chored to resistant structures.

2

1

12w

26

EN

1

4

14

When installing the ducted version, connect the hood to the

chimney using either a flexible or rigid pipe ø 150 or 120 mm,

the choice of which is left to the installer.

• To install a ø 120 mm air exhaust connection, insert the re-

ducer flange 9 on the hood body outlet.

• Fix the pipe using the pipe clamps 25 provided.

• Remove any activated charcoal filters.

9

ø 150

ø 120

25

• Insert the reducer flange 9 on the air outlet of the extractor.

• Attach the adhesive Novastik gasket 13 to the air outlet con-

nection 15 and fix this to the upper frame using the 2 knobs 24.

• Fix the air outlet connection extension piece 14 to the air outlet

connection 15.

• Connect the hood air outlet to the flange in the lower part of

the junction using a rigid or flexible ø 120 tube (by installer’s

choice).

14

15

24

15

14

15

9

EN

1

5

15

• Insert the upper duct and fix it on the top of the upper duct

connection using the 12c screws (2.9 x 9.5) supplied with the

appliance.

Recirculation version

• It is necessary to make sure that the air outlet connection 15 is

placed correctly so that the air outlet grid in it corresponds to

that of the chimney.

• If the grids of the two parts are not corresponding to each

other, it will be necessary to remove the chimney and to adjust

the position of the air outlet connection 15, and at last to as-

sembly the parts again by following the earlier indications.

Before fixing the hood body to the frame:

• Open the suction panel by turning the specific knob.

• Disconnect the panel from the hood canopy by sliding the fix-

ing pin lever.

• Remove the grease filters from the hood body.

• Remove any activated charcoal filters.

• From below, use the 4 screws 12f (M6 x 10) provided to fix the

hood body to the frame.

12c

12f

• Connect the Hood to the mains power supply, inserting a two-

pole cut-out switch with contact aperture of at least 3 mm

along the line.

• Pull the Comfort Panel to open it, ensure that the supply cable

connector is properly inserted into the Suction device socket

• Join the connectors.

• Install the odour filter and the charcoal filter in case the hood is

to be used in recycling version.

• Install the grease filter again, and successively the suction

panel.

EN

1

6

16

A B C D E F G H

Key Function Display

A

Switches the extractor motor on and off at the

latest selected speed

Indicates the selected speed.

B

Decreases the suction speed.

C

Increases the suction speed.

D

By pressing this key it is possible to activate

the intensive speed from any previously se-

lected speed. The intensive speed can be acti-

vated even when the motor is OFF. This speed

has been timed at 10 minutes. After that time

the system activates automatically the latest

selected speed. This function is suitable for

cooking conditions when vapours and smells

are of the utmost emission.

HI appears. The spot down on the right side

flashes once a second.

E

By pressing this key it is possible to set up the

motor to a suction speed at 100 m

3

/h lasting 10

minutes every hour. After this the motor

switches off automatically.

When the filter saturation is going on it is pos-

sible to reset the alarm by pressing this key for

about 3 seconds. The indication is visible only

when the motor is off.

Indicates the 24-function. The spot down on

the right side flashes and the motor is on.

Once the process is finished the previous indi-

cation disappears:

FF Indicates that the metal grease filters

saturation alarm has been triggered, and

the filters need to be washed. The alarm

is triggered after 100 working hours.

EF Indicates that the charcoal filter satura-

tion alarm has been triggered, and the fil-

ter has to be replaced; the metal grease

filters must also be washed. The charcoal

filter is triggered after 200 working hours.

F

By pressing this key it is possible to set the

delayed shutdown of the appliance to 30 min-

utes. This function is suitable for a complete

elimination of the residual smells. It can be

activated at any position, and it is deactivated

by pressing the key again or by switching off

the motor.

Indicates alternately the selected speed of the

hood and the time left before the hood shut-

down. The spot down on the right side flashes.

G

Turns light on and off .

H

Turns light on and off at reduced intensity.

EN

1

7

17

The appliance can be controlled using a remote control powered

by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-

AAA type.

• Do not place the remote control near to heat sources.

• Used batteries must be disposed of in the proper manner.

• Pull the Comfort Panel to open it.

• Disconnect the panel from the hood canopy by sliding the fix-

ing pin lever.

• The comfort panel must never be washed in a dishwasher.

• Clean the outside using a damp cloth and neutral liquid deter-

gent.

• Clean the inside as well using a damp cloth and neutral deter-

gent; do not use wet cloths or sponges, or jets of water; do not

use abrasive substances.

• When the above operation has been completed, hook the panel

back to the hood canopy and close it by turning the knob in the

opposite direction.

EN

1

8

18

Filters can be washed in the dish machine. They need to

be washed when FF-sign appears on the display or in

any case every 2 months, or even more frequently in

case of particularly intensive use of the hood.

Alarm reset

• Switch off the hood and the lights. If the 24h-

function has been activated this has to be deactivated.

• Press the E-key till the display is unlit.

Cleaning the filters

• Pull the comfort panels to open them.

• Remove the filters one by one pushing them towards

the back side of the hood unit and simultaneously

pulling downwards.

• Any kind of bending of the filters has to be avoided

when washing them. Before fitting them again into

the hood make sure that they are completely dry.

(The colour of the filter surface may change through-

out the time but this has no influence to the filter ef-

ficiency).

• When fitting the filters into the hood pay attention

that they are mounted in correct position the handle

facing outwards.

• Close the comfort panel.

EN

1

9

19

• This filter cannot be washed or regenerated. It must be replaced when the EF appears on the

display or at least once every 4 months.

Activation of the alarm signal

• In the recycling version hoods the filter saturation alarm must be activated during the instal-

lation or later.

• Switch off the hood and the lights.

• Disconnect the hood from the mains supply.

• When restoring the connection press and hold B-key.

• When releasing the key two rotating rectangles appear on the display.

• Within 3 seconds press the B-key until a flashing confirmation appears on the dispaly:

• 2 flashes with EF - charcoal filter saturation alarm ACTIVATED

• 1 flash with EF - charcoal filter saturation alarm DEACTIVATED.

Reset of the alarm signal

• Switch off the hood and the lighting. If the 24h-function has

been activated this has to be deactivated.

• Press the E-key until the display is unlit.

Replacing of the filter

• Open the comfort panels pulling them downwards.

• Remove the metal grease filters.

• Remove the saturated charcoal filter by releasing the fixing

hooks

• Fit the new filter and fasten it in its correct position.

• Put the metal grease filters in their seats.

• Close the comfort panels.

20 W halogen light.

• Remove the snap-on lamp cover by levering it from under the

metal ring, supporting it with one hand.

• Remove the halogen lamp from the lamp holder by pulling

gently.

• Replace the lamp with a new one of the same type, making

sure that you insert the two pins properly into the housings on

the lamp holder.

• Replace the snap-on lamp cover.

IT

2

0

20

650 mm min.

Sayfa yükleniyor...

Franke Consumer Products FPL 907 I XS 645H Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Franke Consumer Products FPL 907 I XS 645H Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler