Nilfisk-Advance 56601016 Hızlı başlangıç ​​Kılavuzu

Kategori
Zemin Makinası
Tip
Hızlı başlangıç ​​Kılavuzu
BR 755, BR 755C, BR 855
Quick Start Guide
Hızlı Başlangıç Rehberi
12/08
FORM NO. 56041781
Printed in USA
Nil sk Models: 56601014, 56601015, 56601016
A-English
B-Türkçe
A-2 / ENGLISH
A-2 - FORM NO. 56041781 - BR 755 series
TABLE OF CONTENTS
Page
Introduction ......................................................................A-3
Cautions and Warnings ...................................................A-4
Know Your Machine ................................................A-5 – A-6
Control Panel ...................................................................A-7
Prepare the Machine for Use
Install the Batteries ..........................................................A-8
Install the Squeegee ........................................................A-9
Fill the Solution Tank .......................................................A-9
Detergent (EDS™) System ................................A-10 – A-11
Operating the Machine
Scrubbing ...........................................................A-12 – A-13
Wet Vacuuming .............................................................A-13
After Use ........................................................................A-14
Maintenance Schedule ..................................................A-14
ENGLISH / A-3
FORM NO. 56041781 - BR 755 series - A-3
INTRODUCTION
WARNING!
REFER TO THE ELECTRONIC PRODUCT MANUAL FOR ADDITIONAL OPERATION INSTRUCTIONS AND INFORMATION.
Note: Bold numbers and letters in parentheses indicate an item illustrated on pages 5-7 unless otherwise noted.
GUIDE PURPOSE AND CONTENTS
The purpose of this Quick Start Guide is to provide the operator with all basic information to use the machine properly. For information
about technical characteristics, operation, machine inactivity, maintenance, spare parts and safety conditions refer to the User Manual
on the supplied CD-ROM. Before performing any procedure on the machine, the operators and quali ed technicians must read the User
Manual on the supplied CD-ROM. Contact Nil sk in case of doubts regarding the interpretation of the instructions and for any further
information.
HOW TO KEEP THIS GUIDE
This guide must be kept near the machine, inside an adequate case, away from liquids and other substances that can cause damage to
it.
CONTENT OF THE CD-ROM
The supplied CD-ROM contains an Index, pdf les of all instructions for use manuals, parts lists, service manuals and Adobe Reader®
software installers.
SYSTEM REQUIREMENTS
Windows® - Intel® Pentium® III processor or equivalent.
Microsoft® Windows® Vista, Windows XP Professional, Windows XP Home Edition, Windows Tablet PC Edition with Service Pack 2,
Windows 2000 with Service Pack 4, Windows 2003 Server.
Minimum 512 MB RAM recommended.
Microsoft® Internet Explorer 6.0 or 7.0, Firefox® 1.5, 2.0 or 3.0.
Macintosh® - PowerPC® G3, G4, G5 or Intel® Processor.
Mac OS X version 10.4.3 to version 10.4.9.
Minimum 512 MB RAM recommended.
Safari 2.0.2.
NAMEPLATE
The Model Number and Serial Number of your machine are shown on the Nameplate on the machine. This information is needed when
ordering repair parts for the machine. Use the space below to note the Model Number and Serial Number of your machine for future
reference.
Model Number _____________________________________
Serial Number ______________________________________
CONVENTIONS
Forward, backward, front, rear, left or right are intended with reference to the operator’s position.
SAFETY
The following symbols indicate potentially dangerous situations. Always read this information carefully and take all necessary precautions
to safeguard people and property.
The operators cooperation is essential in order to prevent injury. No accident prevention program is effective without the cooperation of
the person responsible for the machine operation. Most of the accidents that may occur in a factory, while working or moving around, are
caused by failure to comply with the simplest rules for exercising prudence. A careful and prudent operator is the best guarantee against
accidents and is essential for successful completion of any prevention program.
A-4 / ENGLISH
A-4 - FORM NO. 56041781 - BR 755 series
CAUTIONS AND WARNINGS
SYMBOLS
Nil sk uses the symbols below to signal potentially dangerous conditions. Always read this information carefully and take the necessary
steps to protect personnel and property.
DANGER!
Is used to warn of immediate hazards that will cause severe personal injury or death.
WARNING!
Is used to call attention to a situation that could cause severe personal injury.
CAUTION!
Is used to call attention to a situation that could cause minor personal injury or damage to the machine or other property.
Read all instructions before using.
GENERAL SAFETY INSTRUCTIONS
Speci c Cautions and Warnings are included to warn you of potential danger of machine damage or bodily harm.
WARNING!
This machine shall be used only by properly trained and authorized persons.
While on ramps or inclines, avoid sudden stops when loaded. Avoid abrupt sharp turns. Use low speed down hills. Clean only while
ascending (driving up) the ramp.
Keep sparks, ame and smoking materials away from batteries. Explosive gases are vented during normal operation.
Charging the batteries produces highly explosive hydrogen gas. Charge batteries only in well-ventilated areas, away from open
ame. Do not smoke while charging the batteries.
Remove all jewelry when working near electrical components.
Turn the key switch off (O) and disconnect the batteries before servicing electrical components.
Never work under a machine without safety blocks or stands to support the machine.
Do not dispense ammable cleaning agents, operate the machine on or near these agents, or operate in areas where ammable
liquids exist.
Do not clean this machine with a pressure washer.
Only use the brushes provided with the appliance or those speci ed in the instruction manual. The use of other brushes may impair
safety.
CAUTION!
This machine is not approved for use on public paths or roads.
This machine is not suitable for picking up hazardous dust.
Do not use scari er discs and grinding stones. Nil sk will not be held responsible for any damage to oor surfaces caused by
scari ers or grinding stones (can also cause damage to the brush drive system).
When operating this machine, ensure that third parties, particularly children, are not endangered.
Before performing any service function, carefully read all instructions pertaining to that function.
Do not leave the machine unattended without rst turning the key switch off (O), removing the key and applying the parking brake.
Turn the key switch off (O) and remove the key, before changing the brushes, and before opening any access panels.
Take precautions to prevent hair, jewelry, or loose clothing from becoming caught in moving parts.
Use caution when moving this machine in below freezing temperature conditions. Any water in the solution, recovery or detergent
tanks or in the hose lines could freeze, causing damage to valves and ttings. Flush with windshield washer uid.
The batteries must be removed from the machine before the machine is scrapped. The disposal of the batteries should be safely
done in accordance with your local environmental regulations.
Do not use on surfaces having a gradient exceeding that marked on the machine.
All doors and covers are to be positioned as indicated in the instruction manual before using the machine.
SAVE THESE INSTRUCTIONS
ENGLISH / A-5
FORM NO. 56041781 - BR 755 series - A-5
KNOW YOUR MACHINE
As you read this manual, you will occasionally run across a bold number or letter in parentheses - example: (2). These numbers refer
to an item shown on these pages unless otherwise noted. Refer back to these pages whenever necessary to pinpoint the location of an
item mentioned in the text. NOTE: Refer to the service manual for detailed explanations of each item illustrated on the next 3 pages.
1 Operators Seat
2 Solution Tank Drain Hose
3 Drive Pedal, Directional/Speed
4 Drive Wheel
5 Drive Wheel Circuit Breaker (70 Amp)
6 Control Circuit Circuit Breaker (10 Amp)
7 Emergency Stop
8 Scrub Deck
9 Rear Wheel
10 Battery Compartment (under seat)
11 Squeegee Assembly
12 Detergent Cartridge Access Cover (EDS models only)
13 Detergent Cartridge (EDS models only)
14 Deck Skirt Height Adjustment Knob
15 Deck Skirt Removal Knobs
16 Battery Charger Access Door
17 Battery Charger (optional)
18 Seat Adjustment Knob
19 Front Roller Bumper
A-6 / ENGLISH
A-6 - FORM NO. 56041781 - BR 755 series
KNOW YOUR MACHINE
21 Solution Shutoff Valve
22 Solution Filter
23 Steering Wheel Tilt Adjust Knob
24 Control Panel
25 Solution Tank Fill Cover
26 Recovery Tank Cover
27 Vacuum Motor Filter Housing
28 Strainer Basket
29 Recovery Tank Shutoff Float
30 Squeegee Storage Hook
31 Recovery Tank Drain Hose
32 Squeegee Tilt Adjustment Knob
33 Seat Prop-Rod
34 Machine Battery Connector
35 Rear Squeegee Blade Removal Latch
36 Hopper (Cylindrical models only)
37 Recovery Hose
38 Solution Solenoid Valve
39 Front Squeegee Blade Removal Thumb Nut
ENGLISH / A-7
FORM NO. 56041781 - BR 755 series - A-7
CONTROL PANEL
A Key Switch
B Solution Increase Switch
C Solution ON/OFF Switch
C1 Solution Flow Indicators (Normal, Heavy & Extreme)
D Solution Decrease Switch
E EDS ON/OFF Switch
F Display
F1 Hour Meter
F2 Solution Tank Level Indicator
F3 Fault Codes
F4 EDS Indicator (if so equipped)
F5 Detergent Percentage Indicator
F6 Battery Indicator
F7 Recovery Tank FULL Indicator
F8 Battery Low Indicator
G Scrub Pressure Increase Switch
H Scrub ON/OFF Switch
H1 Scrub Pressure Indicators (Normal, Heavy and
Extreme)
I Scrub Pressure Decrease Switch
J EverGreen Switch
K Horn Switch
L Vacuum/Wand Switch
!
!
F
F7
F8
A
C
B
C1
D
J
E
G
H
H1
I
K
L
FF1 F2 F3
F4 F5 F6
A-8 / ENGLISH
A-8 - FORM NO. 56041781 - BR 755 series
BATTERIES
If your machine shipped with batteries installed do the following:
Check that the batteries are connected to the machine  (34).
Turn ON the Key Switch  (A) and check the Battery Indicator (F6). If the gauge is completely lled, the batteries are ready for use. If
the gauge is less than full, the batteries should be charged before use. See the “Charging The Batteries” section.
IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR
INSTRUCTIONS REGARDING SETTING THE CHARGER FOR BATTERY TYPE.
See TSBUS2008-984 for the latest battery charger algorithms.
If your machine shipped without batteries installed do the following:
Consult your Authorized Nil sk dealer for recommended batteries.
Install the batteries by following the instructions below.
DO NOT install two 12 volt batteries in your machine. This affects the stability of the machine.
IMPORTANT!: IF YOUR MACHINE HAS AN ONBOARD BATTERY CHARGER REFER TO THE OEM PRODUCT MANUAL FOR
INSTRUCTIONS REGARDING SETTING THE CHARGER FOR BATTERY TYPE.
See TSBUS2008-984 for the latest battery charger algorithms.
INSTALL THE BATTERIES
WARNING !
Use extreme caution when working with batteries. Sulfuric acid in batteries can cause severe injury if allowed to contact the skin or eyes.
Explosive hydrogen gas is vented from inside the batteries through openings in the battery caps. This gas can be ignited by any electrical
arc, spark or ame.
When Servicing Batteries...
Remove all jewelry.
Do not smoke.
Wear safety glasses, a rubber apron and rubber gloves.
Work in a well-ventilated area.
Do not allow tools to touch more than one battery terminal at a time.
ALWAYS disconnect the negative (ground) cable rst when
replacing batteries to prevent sparks.
ALWAYS connect the negative cable last when installing batteries.
CAUTION!
Electrical components in this machine can be severely damaged if the
batteries are not installed and connected properly. Batteries should be
installed by Nil sk or by a quali ed electrician.
1 Turn the Key Switch (A) off (O) and remove the key. Then swing
open the Battery Compartment Cover (10) and set the Prop-Rod
(33).
2 Using (2) people and an appropriate lifting strap, carefully lift the
batteries into the compartment tray exactly as shown. Refer to
decal 56601589 battery cable layout.
3 See Figure 1. Install battery cables as shown and tighten the nuts
on the battery terminals.
4 Install the battery boots and secure tightly to the battery cables with
the supplied tie straps.
5 Connect the battery pack connector to the machine connector (34)
and close the battery compartment cover.
CAUTION !
Before changing batteries consult TSBUS2008-984 or visit http://www.
nil sk-advance.com
FIGURE 1
ENGLISH / A-9
FORM NO. 56041781 - BR 755 series - A-9
INSTALL THE SQUEEGEE
1 See Figure 2. Slide the Squeegee Assembly (11) onto the squeegee mount bracket and tighten the Squeegee Mount Thumb Nuts
(AA).
2 Connect the Recovery Hose (AB) to the squeegee inlet.
3 Lower the squeegee, move the machine ahead slightly and adjust the squeegee tilt and height using the Squeegee Tilt Adjust Knob
(32) and Squeegee Height Wheel (AC) so that the rear squeegee blade touches the oor evenly across its entire width and is bent
over slightly as shown in the squeegee cross section.
FIGURE 2
FILL THE SOLUTION TANK
Read the cleaning chemical label and calculate the proper amount of chemical to mix for a tank that holds 28 US gallons (106 liters).
Open the Solution Tank Cover (2), then ll the tank 1/3 full of water, add the cleaning chemical, then ll up the tank the remainder of the
way. NOTE: EDS machines can either be used conventionally with detergent mixed in the tank or the EDS system can be used. When using the EDS detergent
dispensing do not mix detergent in the tank, plain water should be used.
CAUTION!
Use only low-foaming, non- ammable liquid detergents intended for automatic scrubber machine applications. Water temperature should
not exceed 130 degrees Fahrenheit (54.4 degrees Celsius).
A-10 / ENGLISH
A-10 - FORM NO. 56041781 - BR 755 series
DETERGENT SYSTEM PREPARATION AND USE (EDS
MODELS ONLY)
COMMON INSTRUCTIONS:
Pressing and releasing the Detergent Switch (E) while the
solution system is active will cause the detergent system to
alternately turn on and off. The system should be purged of
previous detergent when switching to a different detergent.
SERVICE NOTE: Move machine over oor drain before purging
because a small amount of detergent will be dispensed in the
process.
To Purge When Changing Chemicals:
1 Disconnect and remove the detergent cartridge.
2 Turn the Key Switch (A) ON. Press and hold the Solution
Switch (C) and the Detergent Switch (E) down for 3
seconds. NOTE: Once activated the purge process takes
20 seconds. See illustration on next page for Detergent
System indicators. Normally one purge cycle is adequate to
purge the system.
To Purge Weekly:
1 Disconnect and remove the detergent cartridge. Install and
connect a Cartridge lled with clean water.
2 Turn the Key Switch (A) ON. Press and hold the Solution
Switch (C) and the Detergent Switch (E) down for 3
seconds. NOTE: Once activated the purge process takes
20 seconds. See illustration on next page for Detergent
System indicators. Normally one purge cycle is adequate to
purge the system.
When the Detergent Cartridge is almost empty a Display Panel
(F4) indicator will come on. The “Low Detergent” indicator will
remain on until you reset the system. Once this indicator comes
on you should be able to simply pour an entire gallon bottle
of detergent into the Cartridge to re ll without worrying about
measuring. NOTE: Only reset the system when the cartridge is
full. When switching cartridges, the “Low Detergent” indicator is
only accurate if the replacement cartridge is at the same level as
the cartridge being replaced.
To Reset:
1 Turn the Key Switch (A) ON. Press and hold the Solution
Increase Switch (B) and the Solution Decrease Switch
(D) down for 3 seconds. See illustration on next page for
Detergent System indicators.
Detergent Percentage:
1 The detergent percentage default is 0.25%. To change the
percentage, the detergent system must be OFF, then press
and hold the Detergent ON/OFF Switch (E) for 2 seconds.
The detergent indicator will ash and each press of the
switch will cycle through the available percentages (3%, 2%,
1.5%, 1%, 0.8%, 0.66%, 0.5%, 0.4%, 0.3%., 0.25%). Once
the desired percentage is displayed on the screen (F5), stop
and it will lock in after 5 seconds.
CARTRIDGE INSTRUCTIONS:
The Detergent Cartridge (13) is located behind the Detergent
Cartridge Access Door (12) in the operator’s compartment. Fill the
detergent cartridge with a maximum of 1.25 gallons (4.73 Liters) of
detergent. SERVICE NOTE: Remove the detergent cartridge from
the detergent box prior to lling to avoid spilling detergent on the
machine.
It is recommended that a separate cartridge be used for each
detergent you plan to use. The detergent cartridges have a white
decal on them so you can write the detergent name on each cartridge
to avoid mixing them up. When installing a new cartridge, remove the
Cap (AA) and place the cartridge in the detergent box. Install the Dry
Break Cap (BB) and detergent hose as shown.
FIGURE 3
ENGLISH / A-11
FORM NO. 56041781 - BR 755 series - A-11
DETERGENT SYSTEM PREPARATION AND USE (EDS MODELS ONLY)
DETERGENT ENABLED
DETERGENT DISABLED
FULL (RESET)
Press and hold (B) & (D) for 3
seconds to Reset.
LOW DETERGENT
PURGE
Press and hold (C) & (E) for 3
seconds to Purge.
Detergent system is ON when indicator is ON.
A-12 / ENGLISH
A-12 - FORM NO. 56041781 - BR 755 series
OPERATING THE MACHINE
WARNING!
Be sure you understand the operator controls and their functions.
While on ramps or inclines, avoid sudden stops when loaded.
Avoid abrupt sharp turns. Use low speed down hills. Clean only
while ascending (driving up) the ramp.
To Scrub...
Follow the instructions in “preparing the machine for use” section
of this manual.
1 See Figure 4. While seated on the machine, adjust the
steering wheel to a comfortable position using the Steering
Wheel Tilt Adjust Knob (23). The seat can be adjusted if
necessary by tipping up the seat and using the adjustment
knob (18).
2 Turn the Master Key Switch (A) ON (I). This will display
the control panel indicator lights. Reference the Battery
Condition Indicator (F6) and Hour Meter (F1) before
proceeding.
3 To transport the machine to the work area, apply even
pressure with your foot on the front of the Drive Pedal (3)
to go forward or the rear of the pedal for reverse. Vary the
pressure on the foot pedal to obtain the desired speed.
4 Press and hold the Solution Switch (C) to pre-wet the oor,
solution will be dispensed while the switch is held. NOTE:
This will help prevent scarring of the oor surface when
starting to scrub with dry brushes. This must be done prior to
pressing the Scrub ON Switch (H).
5 Press the Scrub ON/OFF Switch (H), the scrub deck and
squeegee will automatically be lowered to the oor. The
scrub, vacuum, solution and detergent (EDS models)
systems all start when the Drive Pedal (3) is activated.
The scrub pressure will default to Normal (one scrub
pressure indicator lit). Use the Scrub Pressure Increase
Switch (G) and Scrub Pressure Decrease Switch (I) to
change between Normal, Heavy and Extreme Scrub modes.
The solution ow rate will automatically adjust to coincide
with the scrub pressure.
NOTE: The solution ow rate can be changed
independently of the scrub pressure by pressing the Solution
Increase Switch (B) or Solution Decrease Switch (D). Any
subsequent scrub pressure adjustments will reset the
solution ow rate to correspond with the scrub pressure.
NOTE: The scrub, solution, vacuum and detergent (EDS
models) systems are automatically enabled when the Scrub
ON/OFF Switch (H) is pressed. Any individual system can
be turned OFF or back ON by simply pressing its switch at
any time during scrubbing.
NOTE: When operating the machine in reverse the
squeegee automatically raises.
6 Begin scrubbing by driving the machine forward in a straight line
at a normal walking speed and overlap each path by 2-3 inches
(50-75 mm). Adjust the machine speed and solution ow when
necessary according to the condition of the oor.
CAUTION!
To avoid damaging the oor, keep the machine moving while the
brushes are turning.
7 When scrubbing, check behind the machine occasionally to see
that all of the waste water is being picked up. If there is water
trailing the machine, you may be dispensing too much solution,
the recovery tank may be full, or the squeegee tool may require
adjustment.
8 The machine defaults to the EverGreen cleaning mode
(EverGreen Switch Indicator is lit GREEN) conserving solution
and detergent. Press the EverGreen Switch (J) to override
the EverGreen cleaning mode and temporarily increase scrub
pressure, solution ow and the detergent percentage. This will
cause the indicator to ash yellow for one minute, solution ow
rate will increase to the next level, scrub pressure will increase to
the next level and the detergent percentage will increase to the
next larger percentage.
9 For extremely dirty oors, a one-pass scrubbing operation may
not be satisfactory and a “double-scrub” operation may be
required. This operation is the same as a one-pass scrubbing
except on the rst pass the squeegee is in the up position (press
the Vacuum/Wand Switch (L) to raise the squeegee). This
allows the cleaning solution to remain on the oor to work longer.
The nal pass is made over the same area, with the squeegee
lowered to pick up the accumulated solution.
10 The recovery tank has a shut-off oat (29) that causes ALL
systems to turn OFF except the drive system when the recovery
tank is full. When this oat is activated, the recovery tank must
be emptied. The machine will not pick up water or scrub with the
oat activated.
NOTE: All other indicators vanish and a “Recovery Tank FULL”
Indicator (F7) appears on the Display Panel when the oat is
activated.
11 When the operator wants to stop scrubbing or the recovery
tank is full, press the Scrub ON/OFF Switch (H) once. This will
automatically stop the scrub brushes and solution ow and the
scrub deck will raise up. The squeegee will raise up after a brief
delay and the vacuum will stop after a brief delay (this is to allow
any remaining water to be picked up without turning the vacuum
back on).
12 Drive the machine to a designated waste water “DISPOSAL
SITE” and empty the recovery tank. To empty, pull the Drain
Hose (31) from its rear storage area, then unscrew the cap (hold
the end of the hose above the water level in the tank to avoid
sudden, uncontrolled ow of waste water). Re ll the solution
tank and continue scrubbing.
NOTE: Make sure the Recovery Tank Cover (26) and the Recovery
Tank Drain Hose (31) cap are properly seated or the machine will not
pick-up water correctly.
ENGLISH / A-13
FORM NO. 56041781 - BR 755 series - A-13
3
18
37
26
29
31
11
!
!
23
L
I
H
G
A
J
D
C
B
F
F7
F8
F1
F5 F6
When the batteries require recharging the Battery LOW Indicator (F8) will come on. Then the scrub brushes and solution ow will stop
and the scrub deck will raise up. The squeegee will raise up after a brief delay and the vacuum will stop after a brief delay. Transport the
machine to a service area and recharge the batteries according to the instructions in the Battery section of this manual.
WET VACUUMING
Steps to follow in tting the machine with optional attachments for wet vacuuming.
1 Disconnect the Recovery Hose (37) from the Squeegee (11). Connect the coupler and hose from the wand kit to the recovery hose.
2 Attach suitable wet pick-up tools to the hose. (An optional Wand Kit PN56601087 is available from Nil sk).
3 Turn the Master Key Switch (A) ON and press the Wand Switch (L). NOTE: The operator cannot be in the seat for the vacuum motor
to run. The vacuum motor will run continuously until the switch is pressed again to turn it OFF. NOTE: The “Recovery Tank FULL”
indicator is disabled when the wand mode is activated. The oat will stop the ow into the recovery tank.
SERVICE NOTE: Refer to the service manual for detailed functional descriptions of all controls and optional programmability.
FIGURE 4
A-14 / ENGLISH
A-14 - FORM NO. 56041781 - BR 755 series
AFTER USE
1 When nished scrubbing, press the Scrub ON/OFF Switch (H), this will automatically raise, retract and stop all the machine systems
(brush, squeegee, vacuum, solution and detergent (EDS models)). Then drive the machine to a service area for daily maintenance
and review of other needed service up keep.
2 To empty the solution tank, remove the Solution Drain Hose (2) from its storage clamp. Direct the hose to a designated “DISPOSAL
SITE” and remove the plug. Rinse the tank with clean water.
3 To empty the recovery tank, pull the Recovery Tank Drain Hose (31) from its storage area. Direct the hose to a designated
“DISPOSAL SITE” and unscrew the plug (hold the end of the hose above the water level in the tank to avoid sudden, uncontrolled
ow of waste water). Rinse the tank with clean water.
4 Remove the brushes or pad holders. Rinse the brushes or pads in warm water and hang up to dry.
5 Remove the squeegee and rinse it with warm water. Open the Recovery tank cover and hang the squeegee from the recovery tank
using the Squeegee Storage Hook (30).
6 Remove the hopper on cylindrical systems and clean thoroughly. Remove from either side of the machine by removing the skirt and
tilting the hopper up and away from housing, then pull out.
7 Check the maintenance schedule below and perform any required maintenance before storage.
MAINTENANCE SCHEDULE
MAINTENANCE ITEM Daily Weekly Monthly Yearly
Charge Batteries X
Check/Clean Tanks & Hoses X
Check/Clean/Rotate the Brushes/Pads X
Check/Clean the Squeegee X
Check/Clean Vacuum Shut-Off Float X
Check/Clean the vacuum motor foam lter(s) X
Empty/Clean Strainer Basket in Recovery Tank X
Clean Hopper on Cylindrical System X
Check Each Battery Cell(s) Water Level X
Inspect Scrub Housing Skirts X
Inspect and clean Solution Filter X
Clean Solution Trough on Cylindrical System X
Purge Detergent System (EDS only) X
Lubrication of Machine X
* Check Carbon Brushes X
* Have Nil sk check the vacuum motor carbon motor brushes once a year or after 300 operating hours. The brush and drive motor
carbon brushes check every 500 hours or once a year.
NOTE: Refer to the Service Manual for more detail on maintenance and service repairs.
8 Store the machine indoors in a clean dry place. Keep from freezing. Leave the tanks open to air them out.
9 Turn the Master Key Switch (A) OFF (O) and remove the key.
B-2 / TÜRKÇE
B-2 - FORM NO. 56041781 - BR 755 series
İÇİNDEKİLER
Sayfa
Giriş ..................................................................................B-3
Önlemler ve Uyarılar .........................................................B-4
Makinenizi Tanıyın ..................................................B-5 – B-6
Kontrol Paneli ...................................................................B-7
Makinenin Kullanıma Hazırlanması
Bataryaların Takılması ......................................................B-8
Lastik Sileceğin Takılması ..............................................B-19
Çözelti Deposunun Doldurulması ...................................B-19
Deterjan (EDS™) Sistemi ................................... B-10 – B-11
Makinenin Çalıştırılması
Ovma ..................................................................B-12 – B-13
Islak Vakumlama ............................................................B-13
Kullanım Sonrası ............................................................B-14
Bakım Çizelgesi ..............................................................B-14
TÜRKÇE / B-3
FORM NO. 56041781 - BR 755 series - B-3
GİRİŞ
UYARI!
EK KULLANIM TALİMATLARI VE BİLGİ İÇİN ELEKTRONİK ÜRÜN KILAVUZUNA BAKINIZ.
Not: Parantez içinde verilen koyu numaralar ve har er, aksi belirtilmedikçe 5-7 arası sayfalarda gösterilen bir parçayı
belirtmektedir.
KILAVUZ AMACI VE İÇİNDEKİLER
Bu Hızlı Başlangıç Kılavuzunun amacı, makinenin doğru kullanılması için operatöre tüm temel bilgileri sağlamaktır. Teknik özellikler,
kullanım, makinenin aktif olmaması, bakım, yedek parçalar ve güvenlik koşullarlı hakkında bilgi için, CD-ROM’da sağlanan Kullanım
Kılavuzuna bakınız. Makinede herhangi bir işlem gerçekleştirmeden önce, operatörler ve yetkili teknisyeler CD-ROM’daki Kullanım
Kılavuzunu okumalıdır. Talimatların yorumlanmasıyla ilgili herhangi bir şüpheniz varsa ve daha ayrıntılı bilgi almak isterseniz, Nil sk ile
irtibat kurun.
BU KILAVUZ NASIL SAKLANMALIDIR
Bu kılavuz makinenin yanında, yeterli bir muhafazada, hasar görmeyecek şekilde sıvılardan ve diğer maddelerden uzak tutulmalıdır.
CD-ROM İÇERİĞİ
Sağlanan CD-ROM’de bir Dizin, kullanım kılavuzlarının tüm talimatlarının pdf dosyaları, yedek parça listeleri, servis kitapçıkları ve Adobe
Reader® yazılımı yükleme programları bulunmaktadır.
SİSTEM GEREKSİNİMLERİ
Windows® - Intel® Pentium® III işlemci veya eşdeğeri.
Microsoft® Windows® Vista, Windows XP Professional, Windows XP Home Edition, Windows Tablet PC Edition with Service Pack 2,
Windows 2000 with Service Pack 4, Windows 2003 Server.
Minimum 512 MB RAM önerilir.
Microsoft® Internet Explorer 6.0 veya 7.0, Firefox® 1.5, 2.0 veya 3.0.
Macintosh® - PowerPC® G3, G4, G5 veya Intel® İşlemci.
Mac OS X sürümü 10.4.3 – sürüm 10.4.9.
Minimum 512 MB RAM önerilir.
Safari 2.0.2.
TANITMA LEVHASI
Makinenizin Model Numarası ve Seri Numarası, makine üzerinde bulunan Tanıtma Levhasında gösterilir. Bu bilgiler, makinenin onarım
parçalarını sipariş ederken gereklidir. Gelecekte gerektiğinde kullanmak üzere makinenizin Model Numarası ve Seri Numarasını yazmak
için aşağıdaki boş alanları kullanın.
Model Numarası ____________________________________
Seri Numarası ______________________________________
STANDARTLAR
İleri, geri, ön, arka, sol veya sağ, operatörün konumuna göredir.
GÜVENLİK
Aşağıdaki simgeler olası tehlikeli durumları belirtir. Her zaman bu bilgileri dikkatlice okuyun ve can ve mal güvenliğini korumak için gerekli
önlemleri alın.
Yaralanmayı önlemek için operatör işbirliği gereklidir. Makinenin kullanımından sorumlu kişinin işbirliği olmadan kaza önleme programı
geçerli olmayacaktır. Bir fabrikada çalışma veya hareket sırasında görülebilecek kazaların çoğuna, en basit kurallara uyulmaması neden
olmaktadır. Dikkatli ve tedbirli bir operatör, kazalara karşı en büyük garantidir ve önleme programının başarılı bir şekilde önlenmesi için
hayati önem taşır.
B-4 / TÜRKÇE
B-4 - FORM NO. 56041781 - BR 755 series
UYARI VE ÖNLEM
SEMBOLLERİ
Nil sk potansiyel tehlikelerin ikazı olarak aşağıdaki sembolleri kullanır. Bu bilgileri dikkatlice okuyup insanların ve eşyaların koruması için
gerekli önlemleri alın.
TEHLİKE!
Ciddi yaralanma ve ölüm tehlikesini belirtir.
UYARI!
Ciddi yaralanma ve ölüm tehlikesine yol açabilecek durumları belirtir.
DİKKAT!
İnsanların, makine veya diğer eşyaların maruz kalabileceği ha f yaralanma ya da hasar oluşturabilecek durumları belirtir.
Kullanmadan önce bütün talimatları dikkatlice okuyunuz.
GENEL GÜVENLİK TALİMATLARI
İnsanlara ve makinelere yönelik potansiyel zararlarla ilgili özel uyarılar ve dikkat edilmesi gereken hususlar aşağıda belirtilmektedir.
UYARI!
Bu makine sadece kali ye ve yetkili personel tarafından kullanılmalıdır.
Yokuş çıkış veya inişlerde, yüklü iken ani duruşlardan kaçının. Ani keskin dönüşler yapmaktan kaçının. Yokuş aşağı inişleri düşük 
hızlarda yapın. Yalnızca yokuş yukarı çıkarken temizlik yapın.
Kıvılcım, çıplak alev ve duman çıkaran maddeleri akülerden uza tutunuz. Normal kullanım esnasında patlayıcı gazlar salınır. Akülerin 
şarj edilmesi oldukça patlayıcı olan hidrojen gazı çıkmasına neden olur. Aküleri, yalnızca iyi havalandırılan, çıplak alevden uzak
yerlerde şarj edin. Aküleri şarj ederken sigara içmeyin.
Elektrik aksamına yakın bölgelerde çalışırken tüm mücevher takılarınızı çıkarın.
Elektrikli aksama bakım yaparken anahtarı kapalı (0) konumuna getirin ve akü bağlantılarını sökün.
Makinenin üstünde duracağı payanda veya takoz olmadan makinenin altında asla çalışmayın.
Yanıcı temizlik maddeleri kullanmayın, makineyi bu gibi maddelerin yanında veya yanıcı sıvıların bulunduğu alanlarda çalıştırmayın.
Bu makineyi basınçlı yıkama cihazları ile yıkamayın.
Bu makineyi %2 den daha yüksek eğimlerde veya yokuşlarda kullanmayın
Yalnızca donanım ile verilmiş olan veya kullanma talimatlarında belirtilen fırçaları kullanın. Diğer fırçaların kullanılması güvenli 
olmayabilir.
D İKKAT!
Bu makine tra ğe açık yollarda kullanıma uygun değildir.
Bu makine tehlikeli tozların toplanması için uygun değildir.
Tırmıklı diskleri ve taş öğütücüleri kullanırken dikkatli olun. Tırmıkların ve taş öğütücülerin kullanılmasından doğabilecek zemin 
hasarlarından Nil sk sorumlu tutulamaz.
Bu makineyi kullanırken üçüncü şahısların, özellikle çocukların tehlike altında kalmamsına dikkat edin.
Herhangi bir bakım ve tamir işlemi gerçekleştirmeden önce talimatları tamamen ve dikkatlice okuyun. 
Kontak Anahtarını (0) konumuna getirip anahtarı çıkartmadan ve aracı emniyete almadan yanından ayrılmayın.
Fırçaları değiştirirken ve panelleri açarken önce Kontak Anahtarını (0) konumuna getirip anahtarı çıkartın.
Saçların, mücevherlerin ve bol giysilerin makinenin hareket eden parçalarına takılmamalarını engellemek için gerekli bütün önlemleri 
alın.
Donma noktasının altındaki sıcaklık şartlarında makineyi hareket ettirirken dikkatli olun. Solüsyon, geri kazanım veya deterjan 
tanklarındaki veya hortumlardaki tüm sular donarak val ara veya armatürlere zarar verebilir. Cam yıkama sıvısı ile yıkayın.
Makine çalışmaz hale gelmeden aküler çıkarılmalıdır. Akülerin imhası yerel yönetmeliklere uygun olarak güvenli bir şekilde 
yapılmalıdır.
Makineyi belirtilenden daha dik yokuşlarda kullanmayın.
Bu makine kullanılmadan önce tüm kapılar ve kapaklar kullanım talimatlarında belirtildiği konumda olmalıdır.
BU TALİMATLARI SAKLAYINIZ
TÜRKÇE / B-5
FORM NO. 56041781 - BR 755 series - B-5
MAKİNENİZİ TANIYIN
Bu kılavuzu okurken, parantez içinde koyu har e yazılmış bir numara veya harf göreceksiniz- örnek: (2). Bu numaralar, aksi
belirtilmedikçe, bu sayfada gösterilen bir bileşene atıf yapmaktadır. Metinde bahsedilen bir bileşenin yerini tam olarak belirlemek için
gerekli olduğunda bu sayfaya bakınız. NOT: Takip eden 3 sayfada gösterilen her bir bileşene ait ayrıntılııklamalar için servis el
kitabına bakınız.
1 Sürücü Koltuğu
2 Çözelti Deposu Akıtma Hortumu
3 Sürme Pedalı, Yön/Hız
4 Tahrik Tekerleği
5 Tahrik Tekerleği Devre Kesicisi (70 Amp)
6 Kontrol Devresi Devre Kesicisi (10 Amp)
7 Acil Durdurma
8 Fırçalama Güvertesi
9 Arka Tekerlek
10 Batarya Bölmesi (koltuk altında)
11 Lastik Silecek Tertibatı
12 Deterjan Kartuş Erişim Kapağı (sadece EDS modelleri)
13 Deterjan Kartuşu (sadece EDS modelleri)
14 Güverte Etekliği Yükseklik Ayar ğmesi
15 Güverte Etekliği Sökme Düğmeleri
16 Batarya Şarj Cihazı Erişim Kapağı
17 Batarya Şarj Cihazı (isteğe bağlı)
18 Koltuk Ayar ğmesi
19 Ön Makaralı Tampon
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Nilfisk-Advance 56601016 Hızlı başlangıç ​​Kılavuzu

Kategori
Zemin Makinası
Tip
Hızlı başlangıç ​​Kılavuzu